I have two different LAP 1300 and 1200 in my network and I need to add theme to the WLC,I successes to add one of theme by the option 60 in the DHCP pool at the Core SW,How to use multiple VCI strings for lap 1300 and 1200 (option 60) in one pool?
View 4 RepliesDoes the pix-501 support multiple SNMP communities? Im trying to add a second one, but the original community string gets removed when I add the new one. If we can have multiple SNMP hosts, then I woud imagine you could have multiple strings. I thought it was like most switches and routers, which can have the following:
snmp-server community STRING1
snmp-server community STRING2
The Pix-501 is currently running on version 6.3(5).
I have two Cisco 1300's acting as bridges only. I have created an infrastructure ssid on VLAN 2 and assigned this to the radio. I am carrying multiple VLANs between the bridges (using subinterfaces on the fastethernet and radio ports).I have enabled WPA-PSK, but how do I check that this is being used between the bridges? Also - I have a switch connected at each end of the bridge. When I make VTP changes, the remote switch does not pick these up - is this because VTP goes over VLAN1 regardless of the Native VLAN (2 in my case)? Do I have to carry VLAN1 over the bridge to get VTP working, or is there an alternative solution?
View 7 Replies View Relatedi need to configure wireless link between my 1300 series, how can i use them like a bridge and access point in the same time?
Do i need static ip for BVI interfacess between them for bridge or its need to be DHCP, is there any example?
I have a Dell Inspiron 1720, that uses a 1300 wireless lan, that keeps crashing. Is there a fix for this, can I replace it with another wireless lan card? Whenever I first start the computer, I would get the error message saying your wireless card had stopped working.
View 4 Replies View RelatedMy wife has a Dell Inspiron 1300 which crashed. I was able to start it again using the Dell Operating System Reinstallation CD for XP Professional but the wifi (wireless) does not work. Before the crash it had a working wireless connection. It appears that I need to reinstall a driver for it. How can I get a driver when I have no internet connection on that computer? I have tried loading on a flash driver from another computer, but it doesn't seem to transfer. What driver do I need and how can I get it to install on her computer?
View 5 Replies View RelatedProduct/Model Number:AIR-BR1310G-A-K9
System Software Filename:c1310-k9w7-tar.123-7.JA
System Software Version:12.3(7)JA
Bootloader Version:12.3(2)JA4 .
We have several of these bridges hanging around; would like to move them one at a time from our 1030WLSE to our 5508WLC (software 7.0.235, so they're compatible).The bridges are all connected to power injectors (AIR-PWRINJ-BLR2). With our 1200's, we apparently just unplug power, hold mode button, plug in power, release mode after about 4 seconds, and they find the new controller (I haven't tried it yet to confirm, but that's what Google...err...Cisco...says will work!). But obviously there's no "mode" or reset button on either the power injector or the bridge itself.
(Other than "shut down the old controller and the bridges and APs will find the new controller". I'll do that at some point, but want to test first with some spare bridges / APs.)
Is it possible to configure two 1300 series bridges at one location, each handling a bridge link to another location to BOTH backup and load balance for each other should one of them fail?
View 5 Replies View RelatedI've been getting warning messages from the event log of a 1300 series bridge, which is set as an Access Point in the network, states: 'Packet to client (mac address) reached max retries, removing the client'; I'm not sure why the client is removed. Does 'reached max retries' mean that the client has tried to many times to connect to the AP/Bridge?
View 1 Replies View RelatedI am trying to install a AIR-BR1310G wireless link between two buildings. I configured the setup in a lab and had everything functioning. Shipped it to the client who is now trying to install it. The radio link is up, but we are having issues with the remote Ethernet connection.The root bridge is connected to a WS-C3560G-24TS (core) switch. The port is setup as a trunk with a native vlan of 2 (our management vlan). [code] if I do a "show power-injector" on the remote radio (no Ethernet link), I get: "Received zero AutoMIB packet from Power Injector, Check to see if CDP is disabled on Fast ethernet" repeating. No other entries. If I do the same command on a unit with a link (root bridge) I get information about "Power Injector Port 0 speed 100Mb/s duplex full link up enabled yes" with a bunch of stats. Similar for "Power Injector Port 1". Power Injector Ports 2-4 as "down" and 5-6 as "disabled". Other than the 3 different patch cables they tried (all straight through) or a crossed cable (try tomorrow when they buy one), is there any other reason the port won't go Up/Up?
View 3 Replies View RelatedMy lap top and pc were both accessing internet fine. Now my laptop has the message windows cannot config. wireless connection. If you have enabled another prog. to manage this connection use that software. Then it says ifI want windows to config., start WZC service. I am a novice and don't understand any of this. I don't think I have done anything to enable another prog to manage the connection. I have tried reloading isp disc and making new network connection but to no avail. the little network logo has a red x constantly.
View 4 Replies View RelatedI have Cisco 1131 & 1300 Light Weight Acces Points and I have 5508 WLAN controller. If i enable the wlan controller internal DHCP Server can this access points will work with this internal DHCP server or do i need to configure DHCP option 43 for these access points? Can these access points works with LWAPP or do i need to configure CAPWAP?
View 4 Replies View RelatedWe have a 1200 Aironet just go down hard for no reason through out the day, we replaced the Power Injector with a C2960 POE Switch, we also replaced the cabiling. When it goes down hard all three lights are still green as if the AP is still up. We verified the IOS with other stores and everything is the same on the configurations, versions, and IOS.
View 35 Replies View RelatedLooking to put a wireless bridge in to connect 2 building about 2000 feet apart. Excellent Line Of Site from rooftop to rooftop. Very little data traffic but will be running Voice over the link. Any have any input on using the 1300 bridges for this application as a permanent install?
View 5 Replies View RelatedI got my final assignment from school, and my teacher asked me to configure 2 Access Points (1200 series) directly on a Wireless Controler (Cisco 2106). I can't ask my teacher for any questions, cause he doesn't know how to configure it also, THAT's why he's asking me to do it.I've learned a lot of things about the default static interfaces (the "management" and "ap_manager" interface), but i can't seem to fully understand how to configure it.I want to use the Internal DHCP server of the WLC. How I can get those 2 Access Points working on the WLC. I only seem to get DHCP issues.
This is what i've done:
- Leave the configuration of the "management" and the "ap_manager" default (172.16.1.30 and 172.16.1.30). Bound to port 1
- Made a new interface "AP1" with IP-Address 10.0.0.10 (/24), default gateway 10.0.0.1. Primary DHCP server: 172.167.1.30
- Made a new interface "AP2" with IP-Address 192.168.1.10 (/24), default gateway 192.168.1.1. Primary DHCP server: 172.167.1.30
- Made 2 DHCP scopes within the 192.168.1.0 and 10.0.0.0 networks.
For some reason, when i boot up both AP's, the won't get any DHCP address.
I have two wireless networks configured in the AP1200, both SSIDs are configured with WPA.
SSID 01: configured whit WPA
SSID 02: configured whit WPA
I have configured the access-list number 700, and I would like to apply to a single network. Achieving the following:
SSID 01 : WPA + Mac Filter, using the ACL number 700.
SSID 02: WPA
How I can apply the list 700 to the first SSID only ??
I am looking at deploying a Cisco Virtual Wireless LAN Controller (vWLC 7.3).Do I need Prime Infrastructure to manage the environment, or can I manage my AP's (1200 series) using the vWLC alone?
View 6 Replies View RelatedI want to disable the MAC authentication that is configured in my Aironet 1200 Cisco Access Point, now set to "Local list only". I want that any wireless device can connect if the user knows the wep password.
I cannot find the option to disable the MAC authentication.
I am using 5 Cisco 1200 Series APs with both an A and G radio. Is there a benefit/problem to running both simultaneously? I would have one SSID and is setup for Fast Roaming as well.
View 1 Replies View RelatedFor the past week, I've been looking to implement wireless technology at our educational site. We've conducted some tests with an AP1200 and we were satisfied with the performances of 802.11a standards.
Since one of our requirements is bandwidth, we are looking to implement a 802.11g standard for that need. Unfortunately, Cisco does not offer any client access adapter for that 11g standard as opposed of the competition. What kind of client adapter (PCMCIA) can Cisco recommend to work with AP1200 under the 802.11g ?
I have 2 Cisco 1200 G AP's connecting 2 different locations. Location A ( La ) I have a RVO82 router connected to a 50Mbit cable connection. I have an AP setup there using a 1 Watt booster and a 24db wire grid directional antenna. Only one antenna here, the other disabled.
At Location B (Lb ), about 1.5 miles away, with good to excellent line of site, i have the other setup as a WGB with a 15db wire grid directional antenna with a 1 Watt booster. Also only one antenna here, the other disabled.
WGB feeds a simple 8 port switch and in that switch i have a simple belkin wireless router setup as an AP for Lb's wireless access,
The signal strenght between the two locations is -49 to -52 db, depending on what time of day I check it.
I have had this setup for a couple of years now. I recently switched from a 3Mbit DSL connection to the 50Mbit cable connection hoping to increase my bandwidth with no luck.
.
When I first set this up i had a 6Mbit cable connection and it maxxed out at 5 Mbit at Lb. I thought i would be able to add more boosters and antennas as time went on to go from half duplex to full duplex (the way i think of it is one antenna receiving and the other sending, at both locations) so that when our ISP had faster rates available, i could upgrade. I recently read somewhere on the net that it is not possible to run full duplex in the AP to WGB setup i have. Is that true?
My main concern is increasing bandwidth on the WGB side Lb. When i upgraded to 50Mbit, i still only max out at 5mbit at Lb. Before i thought it was due to not being full duplex or weaker signal strengths (I've always had the 1watt booster at Lb, then i added one later to La with no benefit noticed except signal strength is better and uploads seem faster from Lb....)
Is there any detailed documentation on the Site Survey Client mode on the AP 1200?When using this mode I cannot see any indication that it has associated withthe root AP. I would like to be able to pass traffic from the ethernet port to the root AP VIA the AP in client mode. The Ap in client mode shows the radio in blocking when in client mode, is this normal? Is there a way to manually change this to forwarding mode?
View 4 Replies View Related I've got an iPad2, which works without issue at home (1130 AP/ASA5505), but at my office, we have a 1200 series AP. It's hit and miss, but other people who bring iPads in have noticed the same issue--our internal SSID is non-broadcast. Even though the SSID is previously configured and works on occassion, there are times where it won't even see the SSID at all to connect.
This happens with iPad and iPad2, iOS4 and iOS5...
LIke i said, works fine on my non-broadcast SSID at my home on an 1130 AP...
how i can limit the bandwidth for a all my client conect to the AP, i have a Aironet 1200 with the 12.2.15 code.
View 3 Replies View RelatedIs there a way to configure client/user to AP authentication without using encryption for joining to an wireless network? What we need to do here is protect network access at our hotspots by enforcing a password to get connected. The other part is making it compatible with every possible device so we need to have encryption off. We have a mixed environment at this time until everything is upgraded. Aironet 1200 series and some new Aironet 1142 models. No controller, all standand alone AP's
View 2 Replies View RelatedI have a WLAN with 5 1200 Series AP (A/G) configured for Fast Roaming using the Cisco supplied documentation. Can I use one user name for all of my devices to connect to the Internal Radius Server? This would be similar to having a passphrase for WPA.
View 3 Replies View RelatedI would like to be able to have a few "guest" users on the Wireless network for visitors. Is there any method to have a prompt for "Username / password"? I would like the user accounts to have different expiry periods if this is possible. My current config is attached. The SSID "test" appears on the network. The SSID "test111" does not appear.
View 1 Replies View RelatedI have a office network that was setup before I started. We have a 172. subnet and a 10.2 subnet. When users on Wifi get a 10.2 address ( ran out of 172 address ) they are not able to get out to the internet. But if the laptop is connected to a LAN port and get a 10.2 address they are able to get to the Internet. Not sure if its the Aps I need to configure or the Pix seeing that if they get a LAN address of 10.2 everything works. This is becoming a bigger issue now that the company has out grown its main subnet (172.)
APs= AIR-AP1231G-A-K9
Vlan = 172.16.1.XXX
Vlan2= 10.2.0.XXX
Hardware: PIX-515E, 64 MB RAM, CPU Pentium II 433 MHz
We had two dozen Aironet 1200 access points and a controller donated to us from a local hospital that no longer needed them. My boss would like me to set one up with 3 VLANs:
- encrypted VLAN for staff
- encrypted VLAN for students
- unencrypted VLAN for guests
Ultimately, we'd like the staff VLAN to have access to all internal network resources, the student VLAN to have access to several pre-defined printers, and the guest VLAN is web-only access. Whether the controller we were given will accommodate that, we won't know until we get one Aironet 1200 programmed and connected to the controller. For the time being, I just want to get this access point programmed with the 3 VLANs.
I'm easily able to get it running a single SSID (non-VLAN) network and confirm that I can use that network fine. However, I need to set up these 3 VLANs. I can connect to it via telnet if that'll let me program it faster.
I am running the upgrade tool on Aironet AP1230B-A-K9. I can't join the controller by using the upgrade tool. the error is "AP does not have Supported Radio". What radio is the upgrade tool or controller look for on Aironet 1200 series? This AP is running 802.11b. However, I have several APs which the same model is running on the same one controller. The controller is model 4402.
View 8 Replies View RelatedI have cisco aironet 1200 series Acess point i want to configure wep with mac authentcation .
If any document with GUI configuration
Is it possible to setup a Cisco 1200 AP with 802.1x to drop users into the corprate network if they have a certificate or if not to put them on the guest network?
View 3 Replies View RelatedI recently purchased a Ciso 1200 Series WAP and I want to bridge this to my existing Cisco Wireless Router So I can extend my coverage. I have done some research but keep coming up short as to where I need to start. Note*(I do not want a physical connection to the WAP, I simply want to be able to bridge the connection from my existing Wireless router to my WAP.
View 1 Replies View Related