I have two wireless networks configured in the AP1200, both SSIDs are configured with WPA.
SSID 01: configured whit WPA
SSID 02: configured whit WPA
I have configured the access-list number 700, and I would like to apply to a single network. Achieving the following:
SSID 01 : WPA + Mac Filter, using the ACL number 700.
SSID 02: WPA
How I can apply the list 700 to the first SSID only ??
I have two Cisco 1260 autonomous access point setup with WPA2-PSK. They are up and running. In that configuration it is Personal security since the security is only provided by the shared key. I'd like to add MAC filtering so in my open authentification I just scroll down to "with MAC filtering" and save. Doing that crash everything and switch to Enterprise security which need to have a Radius server (the shared key is not saved anymore and by using a device I now see 802.1x security).
View 1 Replies View RelatedWe have a 1200 Aironet just go down hard for no reason through out the day, we replaced the Power Injector with a C2960 POE Switch, we also replaced the cabiling. When it goes down hard all three lights are still green as if the AP is still up. We verified the IOS with other stores and everything is the same on the configurations, versions, and IOS.
View 35 Replies View RelatedI got my final assignment from school, and my teacher asked me to configure 2 Access Points (1200 series) directly on a Wireless Controler (Cisco 2106). I can't ask my teacher for any questions, cause he doesn't know how to configure it also, THAT's why he's asking me to do it.I've learned a lot of things about the default static interfaces (the "management" and "ap_manager" interface), but i can't seem to fully understand how to configure it.I want to use the Internal DHCP server of the WLC. How I can get those 2 Access Points working on the WLC. I only seem to get DHCP issues.
This is what i've done:
- Leave the configuration of the "management" and the "ap_manager" default (172.16.1.30 and 172.16.1.30). Bound to port 1
- Made a new interface "AP1" with IP-Address 10.0.0.10 (/24), default gateway 10.0.0.1. Primary DHCP server: 172.167.1.30
- Made a new interface "AP2" with IP-Address 192.168.1.10 (/24), default gateway 192.168.1.1. Primary DHCP server: 172.167.1.30
- Made 2 DHCP scopes within the 192.168.1.0 and 10.0.0.0 networks.
For some reason, when i boot up both AP's, the won't get any DHCP address.
I am looking at deploying a Cisco Virtual Wireless LAN Controller (vWLC 7.3).Do I need Prime Infrastructure to manage the environment, or can I manage my AP's (1200 series) using the vWLC alone?
View 6 Replies View RelatedI want to disable the MAC authentication that is configured in my Aironet 1200 Cisco Access Point, now set to "Local list only". I want that any wireless device can connect if the user knows the wep password.
I cannot find the option to disable the MAC authentication.
I am using 5 Cisco 1200 Series APs with both an A and G radio. Is there a benefit/problem to running both simultaneously? I would have one SSID and is setup for Fast Roaming as well.
View 1 Replies View RelatedFor the past week, I've been looking to implement wireless technology at our educational site. We've conducted some tests with an AP1200 and we were satisfied with the performances of 802.11a standards.
Since one of our requirements is bandwidth, we are looking to implement a 802.11g standard for that need. Unfortunately, Cisco does not offer any client access adapter for that 11g standard as opposed of the competition. What kind of client adapter (PCMCIA) can Cisco recommend to work with AP1200 under the 802.11g ?
I have 2 Cisco 1200 G AP's connecting 2 different locations. Location A ( La ) I have a RVO82 router connected to a 50Mbit cable connection. I have an AP setup there using a 1 Watt booster and a 24db wire grid directional antenna. Only one antenna here, the other disabled.
At Location B (Lb ), about 1.5 miles away, with good to excellent line of site, i have the other setup as a WGB with a 15db wire grid directional antenna with a 1 Watt booster. Also only one antenna here, the other disabled.
WGB feeds a simple 8 port switch and in that switch i have a simple belkin wireless router setup as an AP for Lb's wireless access,
The signal strenght between the two locations is -49 to -52 db, depending on what time of day I check it.
I have had this setup for a couple of years now. I recently switched from a 3Mbit DSL connection to the 50Mbit cable connection hoping to increase my bandwidth with no luck.
.
When I first set this up i had a 6Mbit cable connection and it maxxed out at 5 Mbit at Lb. I thought i would be able to add more boosters and antennas as time went on to go from half duplex to full duplex (the way i think of it is one antenna receiving and the other sending, at both locations) so that when our ISP had faster rates available, i could upgrade. I recently read somewhere on the net that it is not possible to run full duplex in the AP to WGB setup i have. Is that true?
My main concern is increasing bandwidth on the WGB side Lb. When i upgraded to 50Mbit, i still only max out at 5mbit at Lb. Before i thought it was due to not being full duplex or weaker signal strengths (I've always had the 1watt booster at Lb, then i added one later to La with no benefit noticed except signal strength is better and uploads seem faster from Lb....)
I have two different LAP 1300 and 1200 in my network and I need to add theme to the WLC,I successes to add one of theme by the option 60 in the DHCP pool at the Core SW,How to use multiple VCI strings for lap 1300 and 1200 (option 60) in one pool?
View 4 Replies View RelatedIs there any detailed documentation on the Site Survey Client mode on the AP 1200?When using this mode I cannot see any indication that it has associated withthe root AP. I would like to be able to pass traffic from the ethernet port to the root AP VIA the AP in client mode. The Ap in client mode shows the radio in blocking when in client mode, is this normal? Is there a way to manually change this to forwarding mode?
View 4 Replies View Related I've got an iPad2, which works without issue at home (1130 AP/ASA5505), but at my office, we have a 1200 series AP. It's hit and miss, but other people who bring iPads in have noticed the same issue--our internal SSID is non-broadcast. Even though the SSID is previously configured and works on occassion, there are times where it won't even see the SSID at all to connect.
This happens with iPad and iPad2, iOS4 and iOS5...
LIke i said, works fine on my non-broadcast SSID at my home on an 1130 AP...
how i can limit the bandwidth for a all my client conect to the AP, i have a Aironet 1200 with the 12.2.15 code.
View 3 Replies View RelatedIs there a way to configure client/user to AP authentication without using encryption for joining to an wireless network? What we need to do here is protect network access at our hotspots by enforcing a password to get connected. The other part is making it compatible with every possible device so we need to have encryption off. We have a mixed environment at this time until everything is upgraded. Aironet 1200 series and some new Aironet 1142 models. No controller, all standand alone AP's
View 2 Replies View RelatedI have a WLAN with 5 1200 Series AP (A/G) configured for Fast Roaming using the Cisco supplied documentation. Can I use one user name for all of my devices to connect to the Internal Radius Server? This would be similar to having a passphrase for WPA.
View 3 Replies View RelatedI would like to be able to have a few "guest" users on the Wireless network for visitors. Is there any method to have a prompt for "Username / password"? I would like the user accounts to have different expiry periods if this is possible. My current config is attached. The SSID "test" appears on the network. The SSID "test111" does not appear.
View 1 Replies View RelatedI have a office network that was setup before I started. We have a 172. subnet and a 10.2 subnet. When users on Wifi get a 10.2 address ( ran out of 172 address ) they are not able to get out to the internet. But if the laptop is connected to a LAN port and get a 10.2 address they are able to get to the Internet. Not sure if its the Aps I need to configure or the Pix seeing that if they get a LAN address of 10.2 everything works. This is becoming a bigger issue now that the company has out grown its main subnet (172.)
APs= AIR-AP1231G-A-K9
Vlan = 172.16.1.XXX
Vlan2= 10.2.0.XXX
Hardware: PIX-515E, 64 MB RAM, CPU Pentium II 433 MHz
We had two dozen Aironet 1200 access points and a controller donated to us from a local hospital that no longer needed them. My boss would like me to set one up with 3 VLANs:
- encrypted VLAN for staff
- encrypted VLAN for students
- unencrypted VLAN for guests
Ultimately, we'd like the staff VLAN to have access to all internal network resources, the student VLAN to have access to several pre-defined printers, and the guest VLAN is web-only access. Whether the controller we were given will accommodate that, we won't know until we get one Aironet 1200 programmed and connected to the controller. For the time being, I just want to get this access point programmed with the 3 VLANs.
I'm easily able to get it running a single SSID (non-VLAN) network and confirm that I can use that network fine. However, I need to set up these 3 VLANs. I can connect to it via telnet if that'll let me program it faster.
I am running the upgrade tool on Aironet AP1230B-A-K9. I can't join the controller by using the upgrade tool. the error is "AP does not have Supported Radio". What radio is the upgrade tool or controller look for on Aironet 1200 series? This AP is running 802.11b. However, I have several APs which the same model is running on the same one controller. The controller is model 4402.
View 8 Replies View RelatedI have cisco aironet 1200 series Acess point i want to configure wep with mac authentcation .
If any document with GUI configuration
Is it possible to setup a Cisco 1200 AP with 802.1x to drop users into the corprate network if they have a certificate or if not to put them on the guest network?
View 3 Replies View RelatedI recently purchased a Ciso 1200 Series WAP and I want to bridge this to my existing Cisco Wireless Router So I can extend my coverage. I have done some research but keep coming up short as to where I need to start. Note*(I do not want a physical connection to the WAP, I simply want to be able to bridge the connection from my existing Wireless router to my WAP.
View 1 Replies View RelatedI have some aironet 1200 AP's. I want to use this with a windows 2008 radius server. I followed the guide on [URL]. Unfortunately I can not get this working. In the securtiy log of the event viewer there is always the message "authenication was not succesful because an unknown username or incorrect password".
- Is it possible to get this working?
- If yes, is there a manual how to configure the AP's and the radius server, or are there any hints?
- Is this the best way to setup a wireless network or is there a better way?
I saw there is also a local radius server inside the 1200. Can all the 1200's work together? I suppose that if I use the built-in radius server than I can't make a connection to my AD database, correct?
I have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap, but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.
View 6 Replies View RelatedI have a Airnet 1600 Series that I want to add as another repeater to our 1200 series 802.11g network. We already have 2 AP's running fine as Repeater and BR, I just need to a this 1600 AP to the existing wirelss. Everytime I try to change the 1600ap as a repeater, I get the below error.
cannot set role in radio network to when another radio is set to one of the above roles
For years I have received occasional complaints about users being dropped from WiF and then reconnecting like a minute or two later. I wondered what tools people on the Forum used to troubleshoot this transient problem. Cisco APs like the 1200 don't seem to inform about why someone left. One thing that has been very useful over time is using Network Sumbler to see what WAPs are in a vicinity and make sure there is not channel overlap. How to troubleshoot transient wireless network drops?
View 1 Replies View RelatedI'd like to change the SSID name on Aironet 1200 which is currenty used by my wireless network.
View 3 Replies View RelatedI have a Cisco Aironet 1200 series Access point and currently i am using wep with 128 bit . My concern is that i want to change this key with current SSID .
My current SSID is ABtc. My current key is abcdefgh12345. when i try to change the key its give me error :
"encryption key must be 26 hexadecimal characters" .
I just got a Linksys 1200 wireless router and wanted to know how (and the best way) I can turn it off (besides unplugging it) when I am out of town?
View 3 Replies View RelatedI have a cable broadband installed in my home i just bought cisco 1200 series access point...now how to configure my access point. I believe I have to plugged fastethernet cable coming out of my cable modem to access point after that? What I have to do ....do I have to configure the cable modem as wlel or not???
View 2 Replies View RelatedThe client currently has DAS solution integrates with cisco ap1200 which has been eos. As per my knowledge DAS mobile access 2000 doesn't support. 802.11n, is this correct? We are planning to separate the dad environment with cisco. Basically positioning new 3600 n indoor AP to replace existing eos 1200. What are the pro and cons of separating two brands and solutions? Other cabling.The client having coverage issue and adding an amplifier and cable loss may add more issues to existing environment.
Also, based on experience 80211n AP are required is higher density vs 1200.What are your thoughts or best design option to separate das from WLAN environment?
I need to setup my Aironet 1231 to connect some remote computers to a Cisco home wifi unit wirelessly. Here is what I need:
CiscoLinksys E1000 provides my wireless Internet connection in building A ----> Cisco Airnet 1231 is in building B and cat5 cable cannot be run between the buildings. Building B can see building A's wifi signal but only on one side. I need to provide wifi Internet to the entire B building. ---> Cisco 3550 PoE switch ----> another Areonet 1231 ---> Laptops via wifi.
OR
CiscoLinksys E1000 ----> Cisco Airnet 1231 ---> Wifi PC's
Either setup will work. My goal is to provide Internet access to one or more laptops via wifi. How would you set up the Areonet?
As a: Root bridge, Non-root bridge, or a Workgroup bridge?
I just brought home an older desktop and my wireless connection seems to disconnect about every 30 seconds to a minute, then reconnects.
The only other devices that we are using wirelessly are our phones, which we never notice a problem with. When it is connected, the signal stength is excellent. It just keeps dropping. Speed 72.0 mbps.
I am using a Linksys E-1200 wireless N router, and a Belkin N150 USB adapter.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: Intel(R) Pentium(R) 4 CPU 2.80GHz, x86 Family 15 Model 4 Stepping 1
[Code].....