I have a Cisco Aironet 1200 series Access point and currently i am using wep with 128 bit . My concern is that i want to change this key with current SSID .
My current SSID is ABtc. My current key is abcdefgh12345. when i try to change the key its give me error :
"encryption key must be 26 hexadecimal characters" .
Is there a way to configure client/user to AP authentication without using encryption for joining to an wireless network? What we need to do here is protect network access at our hotspots by enforcing a password to get connected. The other part is making it compatible with every possible device so we need to have encryption off. We have a mixed environment at this time until everything is upgraded. Aironet 1200 series and some new Aironet 1142 models. No controller, all standand alone AP's
View 2 Replies View Relatedhow i can limit the bandwidth for a all my client conect to the AP, i have a Aironet 1200 with the 12.2.15 code.
View 3 Replies View RelatedI would like to be able to have a few "guest" users on the Wireless network for visitors. Is there any method to have a prompt for "Username / password"? I would like the user accounts to have different expiry periods if this is possible. My current config is attached. The SSID "test" appears on the network. The SSID "test111" does not appear.
View 1 Replies View RelatedWe had two dozen Aironet 1200 access points and a controller donated to us from a local hospital that no longer needed them. My boss would like me to set one up with 3 VLANs:
- encrypted VLAN for staff
- encrypted VLAN for students
- unencrypted VLAN for guests
Ultimately, we'd like the staff VLAN to have access to all internal network resources, the student VLAN to have access to several pre-defined printers, and the guest VLAN is web-only access. Whether the controller we were given will accommodate that, we won't know until we get one Aironet 1200 programmed and connected to the controller. For the time being, I just want to get this access point programmed with the 3 VLANs.
I'm easily able to get it running a single SSID (non-VLAN) network and confirm that I can use that network fine. However, I need to set up these 3 VLANs. I can connect to it via telnet if that'll let me program it faster.
I have some aironet 1200 AP's. I want to use this with a windows 2008 radius server. I followed the guide on [URL]. Unfortunately I can not get this working. In the securtiy log of the event viewer there is always the message "authenication was not succesful because an unknown username or incorrect password".
- Is it possible to get this working?
- If yes, is there a manual how to configure the AP's and the radius server, or are there any hints?
- Is this the best way to setup a wireless network or is there a better way?
I saw there is also a local radius server inside the 1200. Can all the 1200's work together? I suppose that if I use the built-in radius server than I can't make a connection to my AD database, correct?
I have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap, but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.
View 6 Replies View RelatedI'd like to change the SSID name on Aironet 1200 which is currenty used by my wireless network.
View 3 Replies View Relatedwe have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies View RelatedI'm using the Express Security Set-up tab to configure an Aironet 1142 (stand-alone) access point with EAP.
Objective is to make it a RADIUS client and have laptops authenticate through this access point to a Windows 2008 NPS (Network Policy Server) using computer (machine) certificates - EAP-TLS.
When I select "EAP Authentication" under the "SSID Configuration" I was literally floored to see mention of WEP encryption (a security joke) and no possibility to prefer some variant of WPA (well, apparently not with EAP).
WPA2-Enterprise is what I've selected for "Authentication" and "AES" for encryption in Group Policy (so the laptop clients automatically connect to the access point).
WEP? I bought a Aironet 1142 access point for WEP encryption? How can I configure this securely?
These are currently configured settings as displayed under the "SSID Table" heading:
SSID - "MYSSID"
VLAN - none
Encryption - WEP Mandatory !!!
[Code].....
at one of my Aironet 1200 the update through web interface of the IOS seems failing. THe webpage now looks damaged and not all points are availible.
I now want to update the IOS through telenet. A TFTP server is running and it is sharing the actual TAR-file.
I have two cisco airenet 1252 autonamous access point that are configured as point to point bridge. Now I want to confiure AES encryption or WPA2 using a pre-shared key however I do not see the option to do this . The only option I see under ciphers are:
wep 128
wep 40
TKIP
[Code].....
Is it possible to use either AES or WPA2 using a pre-shared key on the 1252 autonamous access point? preferably using the web interface.
Does Cisco 1142n Aironet Access Point support WPA-PSK with AES encryption ?
View 1 Replies View RelatedI have a Cisco Aironet 1200 Series Access Point. It takes long time to boot up.
After showing the warning banner message it takes long time before asking for username.
The sh version is given below.
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(7)JA4, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2006 by Cisco Systems, Inc.Compiled Tue 05-Sep-06 14:15
[Code].....
how to decode hexadecimal codes: For example 404F10005EC4DC
View 1 Replies View RelatedI just got one of these and it works pretty good except I can't get it to take more than a 32 character WPA2 PSK. Tried using Firefox and IE and it doesn't make a difference. This is for my house. I'm retiring an old Cisco 1200 series AP and as well as a Cisco 1130. Using the same PSK and it doesn't work. Even if I just put 32 characters and just try typing more characters, it doesn't accept any more.Running 1.0.0.3 code and don't see anything newer or any firmware for it for that matter.
View 4 Replies View RelatedI am installing my AE1000 in a new computer. During installation I enter my wireless network password which is on 5 characters long but the next tab does not light up to proceed to the next step. It only lights with 8 characters though my password is 5 characters long
View 2 Replies View RelatedI typed confreg 0x2124 and reset my 2811 and now the characters are not recognizable.
View 4 Replies View RelatedI took a SANS 401 class a few years back, and I remember them showing us how you could break PING (buffer- overflow? memory stack?)by pinging things you wouldn't normally.This was on WinXP I can't duplicate this on Win7, and have forgotten what exactly it was we typed in....I think it was some ALT-code characters, or a tick, 0x33 or something....I realize PING can take octal, decimal, and hexadecimal values?
View 5 Replies View RelatedI have 2811 router and tried to login through AUX port. I am using multitech modem to dial. When i try to login i am getting all special characters in the screen. I have changed the cable but still the same result. I have tried with different link speed also.
When i checked the router , it is showing AUX user is logged in at the time if issue(with show user command).But i am getting only junk character and some times blank screen.
After trying for several hours to configure ldap attribute to cisco attribute mapping, I found that special characters are not supported by ldap attribute-map at least on 8.4
Here is the problematic configuration:
ldap attribute-map ldap_memberof_map
map-name memberOf Group-Policy
map-value memberOf
[Code].....
sometimes I let my friends to use my laptop but unfortunately they can see password of my wireless router which my laptop is connected to by going to this wifi network Properties and then to Security and then check in "Show Characters" box..so is there any way to prevent them from seeing my wifi network password in Windows 7?
View 1 Replies View RelatedWe have a 1200 Aironet just go down hard for no reason through out the day, we replaced the Power Injector with a C2960 POE Switch, we also replaced the cabiling. When it goes down hard all three lights are still green as if the AP is still up. We verified the IOS with other stores and everything is the same on the configurations, versions, and IOS.
View 35 Replies View RelatedI got my final assignment from school, and my teacher asked me to configure 2 Access Points (1200 series) directly on a Wireless Controler (Cisco 2106). I can't ask my teacher for any questions, cause he doesn't know how to configure it also, THAT's why he's asking me to do it.I've learned a lot of things about the default static interfaces (the "management" and "ap_manager" interface), but i can't seem to fully understand how to configure it.I want to use the Internal DHCP server of the WLC. How I can get those 2 Access Points working on the WLC. I only seem to get DHCP issues.
This is what i've done:
- Leave the configuration of the "management" and the "ap_manager" default (172.16.1.30 and 172.16.1.30). Bound to port 1
- Made a new interface "AP1" with IP-Address 10.0.0.10 (/24), default gateway 10.0.0.1. Primary DHCP server: 172.167.1.30
- Made a new interface "AP2" with IP-Address 192.168.1.10 (/24), default gateway 192.168.1.1. Primary DHCP server: 172.167.1.30
- Made 2 DHCP scopes within the 192.168.1.0 and 10.0.0.0 networks.
For some reason, when i boot up both AP's, the won't get any DHCP address.
I have two wireless networks configured in the AP1200, both SSIDs are configured with WPA.
SSID 01: configured whit WPA
SSID 02: configured whit WPA
I have configured the access-list number 700, and I would like to apply to a single network. Achieving the following:
SSID 01 : WPA + Mac Filter, using the ACL number 700.
SSID 02: WPA
How I can apply the list 700 to the first SSID only ??
I am looking at deploying a Cisco Virtual Wireless LAN Controller (vWLC 7.3).Do I need Prime Infrastructure to manage the environment, or can I manage my AP's (1200 series) using the vWLC alone?
View 6 Replies View RelatedI want to disable the MAC authentication that is configured in my Aironet 1200 Cisco Access Point, now set to "Local list only". I want that any wireless device can connect if the user knows the wep password.
I cannot find the option to disable the MAC authentication.
I am using 5 Cisco 1200 Series APs with both an A and G radio. Is there a benefit/problem to running both simultaneously? I would have one SSID and is setup for Fast Roaming as well.
View 1 Replies View RelatedFor the past week, I've been looking to implement wireless technology at our educational site. We've conducted some tests with an AP1200 and we were satisfied with the performances of 802.11a standards.
Since one of our requirements is bandwidth, we are looking to implement a 802.11g standard for that need. Unfortunately, Cisco does not offer any client access adapter for that 11g standard as opposed of the competition. What kind of client adapter (PCMCIA) can Cisco recommend to work with AP1200 under the 802.11g ?
I have 2 Cisco 1200 G AP's connecting 2 different locations. Location A ( La ) I have a RVO82 router connected to a 50Mbit cable connection. I have an AP setup there using a 1 Watt booster and a 24db wire grid directional antenna. Only one antenna here, the other disabled.
At Location B (Lb ), about 1.5 miles away, with good to excellent line of site, i have the other setup as a WGB with a 15db wire grid directional antenna with a 1 Watt booster. Also only one antenna here, the other disabled.
WGB feeds a simple 8 port switch and in that switch i have a simple belkin wireless router setup as an AP for Lb's wireless access,
The signal strenght between the two locations is -49 to -52 db, depending on what time of day I check it.
I have had this setup for a couple of years now. I recently switched from a 3Mbit DSL connection to the 50Mbit cable connection hoping to increase my bandwidth with no luck.
.
When I first set this up i had a 6Mbit cable connection and it maxxed out at 5 Mbit at Lb. I thought i would be able to add more boosters and antennas as time went on to go from half duplex to full duplex (the way i think of it is one antenna receiving and the other sending, at both locations) so that when our ISP had faster rates available, i could upgrade. I recently read somewhere on the net that it is not possible to run full duplex in the AP to WGB setup i have. Is that true?
My main concern is increasing bandwidth on the WGB side Lb. When i upgraded to 50Mbit, i still only max out at 5mbit at Lb. Before i thought it was due to not being full duplex or weaker signal strengths (I've always had the 1watt booster at Lb, then i added one later to La with no benefit noticed except signal strength is better and uploads seem faster from Lb....)
I set the password for the router management consisting of 115 characters. Now I can not log into the router.
1. What is the maximum length of passwords to manage the WAG320N router?
2. What are valid characters in a password for this router?
I have been trying to connect a camera to the wifi router at my mother's assisted living facility. The password has a special character, "!".
After hours waiting on the phone with tech support, they confirmed that only letters and numbers are supported. Guess i have to take it back.
Incidentally, the software is changing "!" to "%21", which is the escape sequence used in URL's. The camera software isn't mapping it back. Should be fixable in firmware.
I have two different LAP 1300 and 1200 in my network and I need to add theme to the WLC,I successes to add one of theme by the option 60 in the DHCP pool at the Core SW,How to use multiple VCI strings for lap 1300 and 1200 (option 60) in one pool?
View 4 Replies View Related