Cisco Wireless :: Change SSID Name On Aironet 1200 Currently Used By Network
Jan 25, 2012I'd like to change the SSID name on Aironet 1200 which is currenty used by my wireless network.
View 3 RepliesI'd like to change the SSID name on Aironet 1200 which is currenty used by my wireless network.
View 3 Replieswe have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies View Related I've got an iPad2, which works without issue at home (1130 AP/ASA5505), but at my office, we have a 1200 series AP. It's hit and miss, but other people who bring iPads in have noticed the same issue--our internal SSID is non-broadcast. Even though the SSID is previously configured and works on occassion, there are times where it won't even see the SSID at all to connect.
This happens with iPad and iPad2, iOS4 and iOS5...
LIke i said, works fine on my non-broadcast SSID at my home on an 1130 AP...
how i can limit the bandwidth for a all my client conect to the AP, i have a Aironet 1200 with the 12.2.15 code.
View 3 Replies View RelatedIs there a way to configure client/user to AP authentication without using encryption for joining to an wireless network? What we need to do here is protect network access at our hotspots by enforcing a password to get connected. The other part is making it compatible with every possible device so we need to have encryption off. We have a mixed environment at this time until everything is upgraded. Aironet 1200 series and some new Aironet 1142 models. No controller, all standand alone AP's
View 2 Replies View RelatedI would like to be able to have a few "guest" users on the Wireless network for visitors. Is there any method to have a prompt for "Username / password"? I would like the user accounts to have different expiry periods if this is possible. My current config is attached. The SSID "test" appears on the network. The SSID "test111" does not appear.
View 1 Replies View RelatedWe had two dozen Aironet 1200 access points and a controller donated to us from a local hospital that no longer needed them. My boss would like me to set one up with 3 VLANs:
- encrypted VLAN for staff
- encrypted VLAN for students
- unencrypted VLAN for guests
Ultimately, we'd like the staff VLAN to have access to all internal network resources, the student VLAN to have access to several pre-defined printers, and the guest VLAN is web-only access. Whether the controller we were given will accommodate that, we won't know until we get one Aironet 1200 programmed and connected to the controller. For the time being, I just want to get this access point programmed with the 3 VLANs.
I'm easily able to get it running a single SSID (non-VLAN) network and confirm that I can use that network fine. However, I need to set up these 3 VLANs. I can connect to it via telnet if that'll let me program it faster.
I have some aironet 1200 AP's. I want to use this with a windows 2008 radius server. I followed the guide on [URL]. Unfortunately I can not get this working. In the securtiy log of the event viewer there is always the message "authenication was not succesful because an unknown username or incorrect password".
- Is it possible to get this working?
- If yes, is there a manual how to configure the AP's and the radius server, or are there any hints?
- Is this the best way to setup a wireless network or is there a better way?
I saw there is also a local radius server inside the 1200. Can all the 1200's work together? I suppose that if I use the built-in radius server than I can't make a connection to my AD database, correct?
I have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap, but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.
View 6 Replies View RelatedI have a Cisco Aironet 1200 series Access point and currently i am using wep with 128 bit . My concern is that i want to change this key with current SSID .
My current SSID is ABtc. My current key is abcdefgh12345. when i try to change the key its give me error :
"encryption key must be 26 hexadecimal characters" .
Is it possible to change one's private network name as well as SSID?
View 1 Replies View Relatedi have a e3000 set up with my network i have guest network set up through the cisco connect but dont see a field to change the guest network broadcast ssid so an ideas?
View 1 Replies View Relatedat one of my Aironet 1200 the update through web interface of the IOS seems failing. THe webpage now looks damaged and not all points are availible.
I now want to update the IOS through telenet. A TFTP server is running and it is sharing the actual TAR-file.
I want to change the SSID on all my APs without it affecting the connected devicesThe users should possible not be affected with the connecttion to the wifi networkHow can I go about it?
View 3 Replies View RelatedI have an established wireless network, using a wired Dell desktop (XP), wireless HP G70-250US notebook (Vista), wireless HP Officejet 650 E709n printer, and Belkin N600 router. To make a long story shorter, both my cable company and Belkin were involved to set up the router a few months ago, and I was assigned an SSID and password that I now want to change. I've received emails from Belkin on changing it at the router - but when it comes to my notebook computer, how to establish a network - I'd like to know how to change the SSID and password in an already-established network, once I've made changes with the router. I'm assuming this is possible? It is my understanding that I don't need to make any changes with my wired desktop, other than to use it when making the router changes? I'm a little familiar with the network configuration setting process with my printer, so am pretty sure I can handle that.
View 7 Replies View RelatedI have a Cisco Aironet 1200 Series Access Point. It takes long time to boot up.
After showing the warning banner message it takes long time before asking for username.
The sh version is given below.
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(7)JA4, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2006 by Cisco Systems, Inc.Compiled Tue 05-Sep-06 14:15
[Code].....
I am using a Aironet 1100 series access point (AIR-AP1142N-N-K9) with IOS version c1140-k9w7-tar.124-21a.JA1. I want to create two seperate SSID's on the access point with WEP encryption. There is no VLAN configured and i want it to be like it. Also I need to broadcast both the SSID's at the same time, so the some of my users need to login with the first SSID and the others to login through the other.
View 2 Replies View RelatedI have configure my AP with to SSID (11 & 12), but I cannot connect to 12. It authenticates, and while trying to acquire IP address from 12, it fails and connects me to 11 (if I have already saved the SSID connection).
The following is my AP status:Product/Model Number:AIR-AP1231G-A-K9 System Software Filename:c1200-k9w7-tar.123-8.JEE System Software Version:12.3(8)JEE Bootloader Version:12.3(2)JA4
The SSID 12 already have 4 clients connected, And I am tring to connect a 5th one (smart phone), but cannot connect to 12, instead coneected to 11. Also tried with a laptop, but cant get the IP address, and give Limited Connectivity error.
I configured the device manually, not even using Express Setup or Express Security setup so... it is possible I missed something.Anyway, here's the problem. Although the SSID is configured as "AP1", this SSID does not appear among available networks on the client laptop.
The connection, configured in Group Policy for the client, should actually happen automatically, based on the SSID, but since the SSID is not being broadcast, that connection is failing as well.
The Aironet does appear among the available networks as "Other Network" and if I click on "connect" I am prompted to enter the SSID -> AP1
Although, unexplicably, an error message displays (Windows cannot connect to the network, or something to that effect), the laptop *does* connect once I close that window. Network access is complete and functional - I can ping other hosts, etc..
I'd post screenshots but not knowing what setting is missing or incorrect, I'd have to print dozens. So here's the sh run output of the AP obtained via telnet (just below). This is a test network so all information is "real" (nothing changed for privacy):
Note: I even changed the hostname to "AP1" (it's still LAB1 below) but that did not resolve the problem (did not think it would).
LAB1#sh runBuilding configuration...
Current configuration : 2321 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname LAB1!logging rate-limit console 9enable secret 5 $1$9EWD$kxrbg8KxikRFypOieKiZh/!aaa new-model!!
[Code]....
We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?
Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies View RelatedI'm facing a problem on vWLC. I configured the vWLC and Aironet 1252, I created 2 SSID with below settings.
1. WPA2 Auth 802.1X
2. Web-Auth
Inside Wireless, I configured this AP Mode as "Local", but all of the client device such as iPhone, Laptop can't find these SSID.
I have an issue where I cannot get clients to change SSID. I have two SSID, one WPA2 secure, one open guest. The secure is locally switched via Flexconnect and the guest is centrally switched. Both of them work. I have been able to test this and both work as intended. The problem is that once you connect to one of them, either secure or guest, you cannot then change to the other. The only way to change is to delete the dhcp entry from the scope and then do it.
Fast SSID change is enabled. I also have debug client output from when the client fails when you try to switch which I will include below. I also pulled some wireshark captures and those show me that the DHCP ack packets are trying to give the client the ip address from the incorrect/previous scope. So basically it's like FAST SSID change is not working and the client is never being disassociated properly??
I am totally stumped and even though the client will most likely not be switched between SSID that often I would still like to know the solution.
Cisco 5508 running 7.2.110.0
Cisco 3502 LWAPP
windows server 2008 dhcp server
[Code].....
I need to configure a Cisco aironet 3602I-K9 because when I connect by the console I can do anything to change the p reconfiguration, this aironet is new and I want to change to autonomous AP, appear errors like:
Translating "CISCO-CAPWAP-CONTROLLER...domain server ()"
CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination . Not in Bound state. I tried to enter to configuration mode but dont valid the configuration terminal command or set command, why happens that?
I cannot find the screen in the interface at 192. Where is this? Please don't say use Cisco Connect disc.
View 1 Replies View RelatedI have a "standart" settings of Cisco Aironet 1240AG with ENABLED broadcasting SSID, encryption is WPA2 (AES). I can see the wifi network (ssid) with windows system but with MAC OS 10.5 and MAC OS 10.7 also with iPhone the wifi is acting like hidden. But If I manually enter the wifi ssid and set the proper encryption the connection work normally. Also I have a separete windows partition on one MACbook and this windows 7 have no problem to see the SSID of my network. But If i Boot to the MAC OS the WIFI is "hidden" until the manually connection. (same problem on iphone, manuall connect with manually entered SSID is working well).
View 2 Replies View RelatedI am working on setting up a new WLAN infrastructure. I have set up different SSIDs connected to different VLANs, in the AP. I also want to use Windows NPS for authenticating users on the different SSIDs, with different authentication methods based on which SSID the user/device is connecting to. To do that, NPS needs to get the SSID, but the Aironet 1240 only sends its MAC address in the Called-Station-Id. I have read a bit about this, and found out that if I have a WLC, it will add the SSID to to the Called-Station-Id. But since we do not have a WLC, I am trying to get this to work anyway. Is it possible to modify the Called-Station-Id to include the SSID on an Aironet 1240? If not, is it possible to send the SSID as a separate attribute that can be read by the NPS?
View 10 Replies View RelatedI have an Aironet 1250 AIR-LAP1252AG-A-K9 I am having issues with, and I am hoping for some direction on how to resolve them. I understand this question has been posted many times many different ways, but i have no luck unfortunately. Here is where I am: I can terminal into the AP, which has been set to factory default, with the username and password and enable password of Cisco. Once I am in the enable mode, I get lost.
Usually there would be an option to go to config. t, and work from there, but this AP does not have that option, Actually if I do a ? at the enable prompt, the commands list only starts with the letter C; but none are config.
I also cannot get into the web interface of the AP. The AP gets a DHCP IP from my DHCP server, (192.1681.128/24) but I cannot get into the web interface using the IP it gets from DHCP. The page never comes up. To add to the confusion, I cannot turn off the CLI event logging, although I enter the command "no debug all". Maybe I am off on what to put in. Nonetheless, it drives me crazy with messages every two seconds as I am trying to type while attempting to figure things out.
Overall, from reading the forums and doing Google searches, I am going on the assumption that the AP is now in lightweight mode, as opposed to autonomous mode, which is where I want it to be. I have tried the method of updating the firmware to the autonomous firmware from Jan 2013 for the AP. I use the TFTP method as I have found here on the forums a few times; I hold the mode button down while applying power to the AP, let the system LED turn red and release the button so the TFTP process can go through, but nothing changes.
I have the AP powered from a gigabit POE switch. The computer I am using for the TFTP is on the same sub net as the AP. I have tried using 10.0.0.6/24 for the computer with the TFTP on it, made sure the view all file extensions option was checked, and renamed the firmware to the .default extension-still nothing updates.
I also noticed that once I hold the mode button down for 20-30 seconds then let it go, the CLI output says the AP it is on the 10.0.0.x sub net, but I cannot ping the computer with the TFTP program on it. If i try to, it get a "Command not supported" message. So I will go on the idea that this is most likely why I cannot do a TFTP update.
About 30 seconds after I release the mode button and the AP boots, it will say it has a 10.0.0.x IP address, then it starts going crazy with messages that it cannot find a DHCP server.
I wonder if there is a way to rename an existing SSID on aironet 1142 without destroying/recreating. I tried downloading configuration/ changing name/ re-uploading however that didn't have desired effect. There doesn't seem to be a way via web-GUI.
View 3 Replies View RelatedWe have three Access Points, two Cisco Aironet 1260 and one 1240AG. Originally, the SSID was hidden on all three AP's and users had to go to Other Networks and type in the SSID and password to access the WAN. About a few months ago, the network started broadcasting to the public. I am trying to make the SSID hidden again. I have tried going to the Security tab, choosing the SSID Manager and setting single guest mode to none but it has not worked.
View 4 Replies View RelatedI have logged into the admin area 192.168.... And I do not see where to change the SSID.
View 2 Replies View RelatedBeen using the WRT160N for a while now and it works great except for one issue. Every few weeks the wireless can't be accessed by the other computers unless I change the SSID name. It was frustrating to figure out, but simply changing the name makes it accessible again.
View 1 Replies View Relatedhow i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?