I have an issue where I cannot get clients to change SSID. I have two SSID, one WPA2 secure, one open guest. The secure is locally switched via Flexconnect and the guest is centrally switched. Both of them work. I have been able to test this and both work as intended. The problem is that once you connect to one of them, either secure or guest, you cannot then change to the other. The only way to change is to delete the dhcp entry from the scope and then do it.
Fast SSID change is enabled. I also have debug client output from when the client fails when you try to switch which I will include below. I also pulled some wireshark captures and those show me that the DHCP ack packets are trying to give the client the ip address from the incorrect/previous scope. So basically it's like FAST SSID change is not working and the client is never being disassociated properly??
I am totally stumped and even though the client will most likely not be switched between SSID that often I would still like to know the solution.
Cisco 5508 running 7.2.110.0
Cisco 3502 LWAPP
windows server 2008 dhcp server
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
I have an issue where I have an AP in one room and another in another.When I walk from one room to the other, I lose signal but manages to see the SSID and join.But, I cannot seem to surf the Internet, I have to manually disconnect and reconnect. Normal wireless routers I reconnect seamlessly without any manual disconnect & reconnect.Currently using cisco 5508 and ap2600.
we have two offices in same city at different location however we are planning to bring both the office at same location.Now lets say site A has controller 5508 configured with 24 AP's with 10.10.10.x subnet for internal SSID and Site B which is shifting to Site A campus has different subnet ( 10.10.20.x ) for same SSID.Site B has no controller since they had connection with H-reap and they were using different subnet for internal SSID ( 10.10.20.x ) .....Now i need to add their AP's in Site A controller which will be extended wireless LAN however we would like to keep same subnet ( 10.10.20.x ) what Site B has for wireless clients which is really confusing me ....I have already client subnet for site A with 10.10.10.x /24 subnet and nearly 200 users are already using this wireless client subnet.... How do i add their ( Site B ) subnet / 10.10.20.x with same SSID configured which is globally only one SSID ?
limitations :I can not create new SSID for site B since same will be broadcasting even in Site A AP's ?Is this possible to map one more subnet of site B to existing SSID with already different subnet ( 10.10.10.x ) ?
I have Internal DHCP Server configured on the Cisco WLC 5508 and all is working fine. DHCP Range is 192.168.1.100 to 192.168.1.245. Now I created another SSID but I want clients connecting to this SSID get specific IP's or from a specific range. WLC has no option to bind a DHCP pool to a specific IP so what I did I checked the option to "Override DHCP" and added the IP of my firewall WLC is connected to and setup a DHCP Pool on that firewall as 192.168.1.89 to 192.168.1.94 (192.168.1.88/29).
Client can connect to the second SSID but can't grab and IP address, what am I missing ?
I am setting up a Cisco 5508 wireless controller and was looking for some feedback or assistance. Basically I already have my guest SSID configured and functioning. Created an interface group containing my vlans and applied the created ACL "Guest Policy - internet only", which is also working.I want to setup a second SSID called "staffstudent" and use RADIUS for authentication. I have already created two separate network policies on the radius server: staff and student. Each only allows certain user groups. I want to be able to differentiate on the controller side which profile they are logging in on and then apply the correct ACL. I have two currently configured: one for staff and one for student. It appears to me that since you have to apply the ACL at the interface level I cannot use both since my interface is accepting both staff and students. Is there a way I can filter them using RADIUS so that when they login RADIUS can return a "student" value and then apply the correct ACL? Same for staff?
setup a WEP SSID on my 5508 controllers. THat being said, I have multiple sites with extremely old scan guns that only do 104bit wep. I plan on locally switching this SSID and using static WEP 104bit key with MAC authentication, and then ACLing to limit my inherent security issues/exposure once someone compromises my WEP key. [code]
On a wlc 5508-7.0.116, can I set up 2 ssids that map to one wlan/vlan/subnet. I thought you could but I don't have the means to test without breaking production.
I have Build a 5508-HA Cluster (7.4.100.0) , hat to reboot this cluster due to Licens install.After the reboot atleast one of the SSIDs was not broadcasting anymore, even the checkbox was checked.
What did I do:
Installed the Licenses @ Freiday 12:00 @17:15 reload active WLC, wait till controller is up again (a few minutes pingable) @17:25 force failover to first controller. check a few SSIDs but not all, those who where check are ok. @monday 07:00 clients complaining not seeing the SSID (some where connected)
on a 5508 WLC can we create new SSID for I PAD / IPHONE Users without having ISE, only I phone / I PAD are allowed to be authenticated rest all should be denied. IS this possible?
I have a wireless lan controller (5508) broadcasting 2 SSID's, once is a secure vlan grabbing an ip address from a local dhcp server and getting access to the internal network, and the other ssid is for a guest vlan where the dhcp server is in a remote site and internet access is off a circuit in our data center which is accessed over a wan. The secure ssid's vlan is defined on the local switch, but the guest vlan is not defined on the local switch.the ap's in the respective sites are trunked to the core switch and the switchport config is : [code] it's trunked b/c we have both vlans going across this physical connection.I would like get the guest vlan a wired connection, ie. off a switchhub, but not sure how to do that as this guest vlan is not defined on our local network.
I have an open SSID on 5508 controllers - configured as anchors and need to redirect wireless clients to the wireless help page automatically once they have connected and opened their browser.I've read all through the web auth and pass through discussions on here but nothing seems to be quiet right for me - unless I am completely missing something.
I have two WLC-5508 for 50 AP's deployed. One is primary controller & other is secondary.Recently noticed an unknown "authorization failed, no sufficient privileges for user" message poping up while making configuration changes in WLC. Specificly when trying to create an new SSID. WLC Authentication is local. This message poped up earlier once or twice but it didnt prevent from making changes that time.
I have a 5508 WLC controller at the HQ with the employee ssid ,the dhcp scope on the ssid is 10.120.0.0/16 network.
However,I want this same ssid to be brodcasted to a remote site using HREAP access point but with different dhcp scope 10.102.0.0/16.
I have tried creating another interface for the remote site with a different dhcp scope(10.102.0.0) but the controller wont allow me create another wlan with same ssid that existed before to apply the new interface created for.
I need raise a especial configuration to 34 APs LWAPP associated to WLC 5508 with IOS 7.0.220
This is the Scenario:We have 34 APs LWAPP with 2 SSID (Corporative & Guest), with 2 DHCP different. The Guest SSID receive IP to DHCP from WLC while SSID Corporative receive IP from Microsoft DHCP. The AP On Site are Local and the Foreign AP are configured like H-REAP (H-REAP Local switching and Learn Client IP Address are marked)
Here is the thing, I need configure a new WLAN (Pruebas) for add to 34 APs (Local and Foreign) but this new WLAN must be receive IP from a New Microsoft DHCP
Firstly I configured a new Physical interface and linked to New WLAN (Pruebas) however i don't know how configure the AP and the DHCP because I want that the AP deliver IP addresses depending the Locality.The last because the SuperScope from DHCP is divided in various subnets and because the IP from the AP will be in another VLAN
Been using the WRT160N for a while now and it works great except for one issue. Every few weeks the wireless can't be accessed by the other computers unless I change the SSID name. It was frustrating to figure out, but simply changing the name makes it accessible again.
i have two 5508 ver 7.3.0, one is the primary and one is the guest controller. mobility is up and running. i have an exising guest ssid working with wpa2-psk and web authentication and its working fine but i require a second guest ssid that only uses a wpa2-psk for ipod/ipads as i cant use passive client on primary controller. i presently have the one vlan range and dhcp setup on the guest controller to give addressing to either ssid. i know you can have multiple ssid setup on the guest controller but in other sites i have only had one guest connection comming from the primary controller, just a primary controller on each sites was only creating one link to the same guest controler.
Has anyone come accross a problem whereby an SSID becomes unavailable when selecting a Radio Policy of '802.11g Only'? The SSID is configured identically accross multiple controllers, but only works on the WISM's. The same WLAN profile on a 5508 is unavailable unless I select a Radio Policy of 'All'.
All controllers (WISM's and 5508's are running 6.0.188.0)The WLAN profile is using MAC Filtering[WPA2][Auth(802.1X)] as the security policy.
i have a e3000 set up with my network i have guest network set up through the cisco connect but dont see a field to change the guest network broadcast ssid so an ideas?
I had to default my wireless router " Netgear WGR14V6" and since then I haven't been able to connect with my wireless card. I can physically connect to it with a cable but I can't access it with the wireless card. When I look at the properties it says that it is working fine but I can't seem to find where to change the "SSID and the security phrase". Usually when it is up and running it has a status button and when you click on it there is a tab that you click on and it shows you the SSID and the rest, but now since it is not connected there isn't anything that I can find to change this.
I connected the Router to the modem, and all the wired connected PCs were working perfectly.But then, i went to the setup page to configure the Wireless settings, and as soon I changed the SSID name, the connection internet connection droppedThe only way i had to fix this was by making a Hard Reset.after that, I also tryed changing values and settings from all the configuration tabs, and the wired connection was working properly, but as soon i changed any value from the Wireless tab, the internet connection dropped (even, in the diagnostics section, i could not do a ping to google. It says unknown host).
How can i change AP host name for LAP via CLI? I got the error 'command is disabled' when i try to use command 'capwap ap hostname <>'
I try to disconnect LAP from WLC, factory default, clear all private-configure and clear all files in nvram: but not working (still got error). I cannot change via WLC GUI for CAP2602I series. I don't know why.
I checked bug CSCsy17745 but current in use software is fixed.
