I have an open SSID on 5508 controllers - configured as anchors and need to redirect wireless clients to the wireless help page automatically once they have connected and opened their browser.I've read all through the web auth and pass through discussions on here but nothing seems to be quiet right for me - unless I am completely missing something.
View 5 RepliesWe need to create Guest WLAN on WLC 5508 which will be used for internet access only. My questions are:
1. Is it possible to use our external web proxy server to authenticate users?
2. Can we also forward all traffic to the external web proxy to filter the websites that can be accessed (without configuring it on the browser)?
3. Can this be achieved using the L3 webauth?
Our topology:
WLC -- Switch -- ASA Firewall -- Internet -- External Web Proxy
We are using WLC as DHCP server for Guest WLAN with ASA Firewall as the gateway.
I have a problem with a customer of mine. We have deployed two new WLC5508 running r7.0.116.0 and AP1142s, also WCS with r7.0.172. When we setup a "Guest Access" we ran into trouble.The problem is that we can associate to the SSID/AP and get an ip-adress. When we open the web- browser we do not get redirected to the virtual interface but instead the _hostname_ of the WLC. Like this: url...
I we manually replace "cisco6a19c4" with 1.1.1.1 it works as it should, the login page appears, we login and can access the internet.We have tested and disabled web-auth on the ssid an everything works, we can directly go out on the internet, DNS works without any problems. [code]Guest network (VLAN) is transfered from WLC via the trunk to the Cat4503 and then connected on a access-port to a separate broadband-router, then to the inetrnet.DHCP to guest-users from separate broadband-router which is def gwy and "DNS".On the virtual interfaces no hostname is configured.
I have a 5508 WLC running 6.0.202.0. It functions as the Anchor Controller for the guest network. It sits in our Internet DMZ and is isolated from the rest of the network. It does not connect to AD, ACS, etc. The guest wireless WLAN is configured for Web Policy - Authentication. I have a customized login page. Credential management is done by WCS.
Users are connecting to the guest wireless network and entering their creds with no issues using mobile devices (iPad, etc). Then the mobile device goes to sleep / turns off and when they go to use it again, they have to type their creds in again. They dont like retyping their creds throughout the day.
good way mitigate the multiple logins? Something like a 'save password' option on the customized page?
i have a simple router on a stick config which is providing dhcp to a customer SSID. however i don't want employees to stay on it and eat the band width since its open. the lease is set to an hour, is there anyway that i could set it so that once your lease expired it can't be renewed for 4 about 8 hours? I am using a cisco 2600 router in this setup.
View 1 Replies View RelatedIs it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
We’re currently using 5508 WLC’s and leveraging Cisco ISE for radius/authentication rule sets.I’m trying to get a splash page to flash and then redirect to a website after a successful authentication to an SSID. Everything on the wireless side works with no splash page (users connect to SSID,authenticate with AD credentials using 802.1X PEAP to our Cisco ISE box, and gain access to the network).When I enable ‘Splash Page Web Redirect’ on the WLC (under L3 security), I’m unclear on the ISE box where I set this up. When I look in the Cisco documention it says:Splash Page Web Redirect—If you select this option, the user is redirected to a particular web page after 802.1X authentication successfully completes. After the redirect, the user has full access to the network. You can specify the splash web page on your RADIUS server. How I specify this on the ISE box? Or am I totally off base?
View 10 Replies View RelatedI have an issue where I have an AP in one room and another in another.When I walk from one room to the other, I lose signal but manages to see the SSID and join.But, I cannot seem to surf the Internet, I have to manually disconnect and reconnect. Normal wireless routers I reconnect seamlessly without any manual disconnect & reconnect.Currently using cisco 5508 and ap2600.
View 8 Replies View Relatedwe have two offices in same city at different location however we are planning to bring both the office at same location.Now lets say site A has controller 5508 configured with 24 AP's with 10.10.10.x subnet for internal SSID and Site B which is shifting to Site A campus has different subnet ( 10.10.20.x ) for same SSID.Site B has no controller since they had connection with H-reap and they were using different subnet for internal SSID ( 10.10.20.x ) .....Now i need to add their AP's in Site A controller which will be extended wireless LAN however we would like to keep same subnet ( 10.10.20.x ) what Site B has for wireless clients which is really confusing me ....I have already client subnet for site A with 10.10.10.x /24 subnet and nearly 200 users are already using this wireless client subnet.... How do i add their ( Site B ) subnet / 10.10.20.x with same SSID configured which is globally only one SSID ?
limitations :I can not create new SSID for site B since same will be broadcasting even in Site A AP's ?Is this possible to map one more subnet of site B to existing SSID with already different subnet ( 10.10.10.x ) ?
I have an issue where I cannot get clients to change SSID. I have two SSID, one WPA2 secure, one open guest. The secure is locally switched via Flexconnect and the guest is centrally switched. Both of them work. I have been able to test this and both work as intended. The problem is that once you connect to one of them, either secure or guest, you cannot then change to the other. The only way to change is to delete the dhcp entry from the scope and then do it.
Fast SSID change is enabled. I also have debug client output from when the client fails when you try to switch which I will include below. I also pulled some wireshark captures and those show me that the DHCP ack packets are trying to give the client the ip address from the incorrect/previous scope. So basically it's like FAST SSID change is not working and the client is never being disassociated properly??
I am totally stumped and even though the client will most likely not be switched between SSID that often I would still like to know the solution.
Cisco 5508 running 7.2.110.0
Cisco 3502 LWAPP
windows server 2008 dhcp server
[Code].....
I have Internal DHCP Server configured on the Cisco WLC 5508 and all is working fine. DHCP Range is 192.168.1.100 to 192.168.1.245. Now I created another SSID but I want clients connecting to this SSID get specific IP's or from a specific range. WLC has no option to bind a DHCP pool to a specific IP so what I did I checked the option to "Override DHCP" and added the IP of my firewall WLC is connected to and setup a DHCP Pool on that firewall as 192.168.1.89 to 192.168.1.94 (192.168.1.88/29).
Client can connect to the second SSID but can't grab and IP address, what am I missing ?
I am setting up a Cisco 5508 wireless controller and was looking for some feedback or assistance. Basically I already have my guest SSID configured and functioning. Created an interface group containing my vlans and applied the created ACL "Guest Policy - internet only", which is also working.I want to setup a second SSID called "staffstudent" and use RADIUS for authentication. I have already created two separate network policies on the radius server: staff and student. Each only allows certain user groups. I want to be able to differentiate on the controller side which profile they are logging in on and then apply the correct ACL. I have two currently configured: one for staff and one for student. It appears to me that since you have to apply the ACL at the interface level I cannot use both since my interface is accepting both staff and students. Is there a way I can filter them using RADIUS so that when they login RADIUS can return a "student" value and then apply the correct ACL? Same for staff?
View 2 Replies View Relatedis it possible to multicast between 2 different SSID's that are associated to 2 different VLAN's?
View 2 Replies View Relatedsetup a WEP SSID on my 5508 controllers. THat being said, I have multiple sites with extremely old scan guns that only do 104bit wep. I plan on locally switching this SSID and using static WEP 104bit key with MAC authentication, and then ACLing to limit my inherent security issues/exposure once someone compromises my WEP key. [code]
View 4 Replies View RelatedWe created the management interface, an internal DHCP scope in same subnet, and Two SSID tied to the same management interface:
- when we connect to the first SSID we have and IP address
- but when we connect to the secone SSID: impossible to get an ip address - auth and association are OK
On a wlc 5508-7.0.116, can I set up 2 ssids that map to one wlan/vlan/subnet. I thought you could but I don't have the means to test without breaking production.
My goal is this:
Ssid red open
Ssid blue wpa 2
But all clients on the same ip subnet
I have Build a 5508-HA Cluster (7.4.100.0) , hat to reboot this cluster due to Licens install.After the reboot atleast one of the SSIDs was not broadcasting anymore, even the checkbox was checked.
What did I do:
Installed the Licenses @ Freiday 12:00
@17:15 reload active WLC, wait till controller is up again (a few minutes pingable)
@17:25 force failover to first controller.
check a few SSIDs but not all, those who where check are ok.
@monday 07:00 clients complaining not seeing the SSID (some where connected)
on a 5508 WLC can we create new SSID for I PAD / IPHONE Users without having ISE, only I phone / I PAD are allowed to be authenticated rest all should be denied. IS this possible?
View 8 Replies View RelatedI have a wireless lan controller (5508) broadcasting 2 SSID's, once is a secure vlan grabbing an ip address from a local dhcp server and getting access to the internal network, and the other ssid is for a guest vlan where the dhcp server is in a remote site and internet access is off a circuit in our data center which is accessed over a wan. The secure ssid's vlan is defined on the local switch, but the guest vlan is not defined on the local switch.the ap's in the respective sites are trunked to the core switch and the switchport config is : [code] it's trunked b/c we have both vlans going across this physical connection.I would like get the guest vlan a wired connection, ie. off a switchhub, but not sure how to do that as this guest vlan is not defined on our local network.
View 1 Replies View RelatedI have two WLC-5508 for 50 AP's deployed. One is primary controller & other is secondary.Recently noticed an unknown "authorization failed, no sufficient privileges for user" message poping up while making configuration changes in WLC. Specificly when trying to create an new SSID. WLC Authentication is local. This message poped up earlier once or twice but it didnt prevent from making changes that time.
View 3 Replies View RelatedI have a 5508 WLC controller at the HQ with the employee ssid ,the dhcp scope on the ssid is 10.120.0.0/16 network.
However,I want this same ssid to be brodcasted to a remote site using HREAP access point but with different dhcp scope 10.102.0.0/16.
I have tried creating another interface for the remote site with a different dhcp scope(10.102.0.0) but the controller wont allow me create another wlan with same ssid that existed before to apply the new interface created for.
My customer wants to have mapping of WLAN SSID with different authentication protocol as show below .
1: EMP-M for Mschap
2: EMP-G for Peap GTC
3: EMP-T for TLS
For example EMP-M SSID users should be connected with only PEAP(MSCHAPv2) and not on other methods like PEAP-GTC/EAP-TLS .
customer is currently having WLC 5508 and using ISE for AAA . Any tip how we can do the above requirement through WLC .
I have a 4400 and a 5508 WLC in the same location We want to be able to roam between ap joined to both the 4400 and the 5508 using only one ssid
Do I only need to create a mobility group and add both WLC then create only one WLAN on one of the controllers and it will be shared across bot WLC.
I need raise a especial configuration to 34 APs LWAPP associated to WLC 5508 with IOS 7.0.220
This is the Scenario:We have 34 APs LWAPP with 2 SSID (Corporative & Guest), with 2 DHCP different. The Guest SSID receive IP to DHCP from WLC while SSID Corporative receive IP from Microsoft DHCP. The AP On Site are Local and the Foreign AP are configured like H-REAP (H-REAP Local switching and Learn Client IP Address are marked)
Here is the thing, I need configure a new WLAN (Pruebas) for add to 34 APs (Local and Foreign) but this new WLAN must be receive IP from a New Microsoft DHCP
Firstly I configured a new Physical interface and linked to New WLAN (Pruebas) however i don't know how configure the AP and the DHCP because I want that the AP deliver IP addresses depending the Locality.The last because the SuperScope from DHCP is divided in various subnets and because the IP from the AP will be in another VLAN
I'm using a Cisco Wireless LAN Controller 5508, 14x Access Points 1041 and 6x Access Points 1031 in combination with a NCS 1.0.
Is it possible to broadcast SSID'S only on defined Access Points, e.g. AP 1-3,7-10,18? If yes, what have I to do?
i have two 5508 ver 7.3.0, one is the primary and one is the guest controller. mobility is up and running. i have an exising guest ssid working with wpa2-psk and web authentication and its working fine but i require a second guest ssid that only uses a wpa2-psk for ipod/ipads as i cant use passive client on primary controller. i presently have the one vlan range and dhcp setup on the guest controller to give addressing to either ssid. i know you can have multiple ssid setup on the guest controller but in other sites i have only had one guest connection comming from the primary controller, just a primary controller on each sites was only creating one link to the same guest controler.
View 3 Replies View RelatedHas anyone come accross a problem whereby an SSID becomes unavailable when selecting a Radio Policy of '802.11g Only'? The SSID is configured identically accross multiple controllers, but only works on the WISM's. The same WLAN profile on a 5508 is unavailable unless I select a Radio Policy of 'All'.
All controllers (WISM's and 5508's are running 6.0.188.0)The WLAN profile is using MAC Filtering[WPA2][Auth(802.1X)] as the security policy.
I am beginning to get many emails from users who have recently upgraded to OS6 and saying now they cannot connect to our open access wireless network. We use a separate server that users must agree to a user agreement page and they say they get it, but after agreeing, it goes blank and they cannot connect. I am using mostly Cisco 3502's with the 5508 controller using 7.0.112.0 IOS version. Nobody in our IT department has yet to test OS6 yet.
View 9 Replies View RelatedI'm currentlly running Both Wired and Wireless GPO via Win2008r2, on my WIRED connections after clt-alt-del logoff my network connection stays open (pingable)While connected via wireless (WLC 5508 and WCS) Windows AD 2008r2 ;Radius Server 2003.
All Clients authenticate using Network Authen (Wireless Network Connection Properties) WPA2 Data encryp AES EAP type PEAP.Authentication Method (EAP-MSCHAP) I have no problems connecting via SSID etc... my Question is how do I keep the TCP connection open after initiating a logoff from Windows. (Closing network connection) OPEN!
I need to maintain a tcp(pingable) connection open in order to access Manufacturing clients that are connected via WIFI. (WLC).All wireless clients are issued and auto-enrollment cert via IAS .
We have a network of multiple WLCs: 5508, 4402, WISMs in two C6509 all running version 7 software. We have about a dozen SSIDs and we need to provide DHCP to the one public SSID (which like the other SSIDs span across all controllers) and to do so we thought of using a spare router, Linux workstation or DHCP server on the controllers. We are not sure if using the controllers is an option since we have multiple controllers. Is there a way to setup DHCP on a WLC and tell the others to use that WLC for DHCP for the one SSID?
View 3 Replies View RelatedBeen a while since I have conf'd a controller. I believe its WLAN/edit/security/layer2 and below psk format edit the password?
View 2 Replies View RelatedI have a wireless network with LWAPPs and 1 WLC 5508. How to block communication between SSIDs (clients in different SSIDs bassically) and whether that is even possible from the controller? I'd like to mention that communication between clients whithin the same SSID is already blocked.
View 4 Replies View RelatedI am trying to set up a guest SSID which will be separate from other corp SSIDs. I have read about this auto-anchor feature and I have a basic idea. Here are some questions about the network design
1. Can Cisco 5508 with 7.2.111.3 code do NAT? I mean can I use the anchor controller also as a gateway to Internet or do I need another device such as FW or router to do the job?
2. I want the guests to get IP address in 192.168.0.0/24 range. On the anchor controller I will need an interface in this range, correct? However on the internal controller I won't need this interface. The guest ssid will be associated with the management interface on the internal controller, correct?
3. I want the guests to get IP address from general DHCP server. Does DHCP request have to come out of the new interface in the 192.168.0.0/24 range? However this interface will be connecting with the FW. It won't have connection back to the internal network to reach the DHCP server. The management interface will have the route to the DHCP server. Is it possible to use management interface for this SSID but still let traffic to pass through the Guest interface?