Cisco Wireless :: WLC 5508 - AP LWAPP With 2 SSID / DHCP Differences?
Jul 22, 2012
I need raise a especial configuration to 34 APs LWAPP associated to WLC 5508 with IOS 7.0.220
This is the Scenario:We have 34 APs LWAPP with 2 SSID (Corporative & Guest), with 2 DHCP different. The Guest SSID receive IP to DHCP from WLC while SSID Corporative receive IP from Microsoft DHCP. The AP On Site are Local and the Foreign AP are configured like H-REAP (H-REAP Local switching and Learn Client IP Address are marked)
Here is the thing, I need configure a new WLAN (Pruebas) for add to 34 APs (Local and Foreign) but this new WLAN must be receive IP from a New Microsoft DHCP
Firstly I configured a new Physical interface and linked to New WLAN (Pruebas) however i don't know how configure the AP and the DHCP because I want that the AP deliver IP addresses depending the Locality.The last because the SuperScope from DHCP is divided in various subnets and because the IP from the AP will be in another VLAN
View 3 Replies
ADVERTISEMENT
Oct 15, 2012
What is the difference between WIRELESS LAN LWAPP and WIRELESS LAN LWAP RECOVERY images? I believe the RECOVERY is used in the upgade process - but what is the other used for?
View 1 Replies
View Related
Apr 22, 2012
I have Internal DHCP Server configured on the Cisco WLC 5508 and all is working fine. DHCP Range is 192.168.1.100 to 192.168.1.245. Now I created another SSID but I want clients connecting to this SSID get specific IP's or from a specific range. WLC has no option to bind a DHCP pool to a specific IP so what I did I checked the option to "Override DHCP" and added the IP of my firewall WLC is connected to and setup a DHCP Pool on that firewall as 192.168.1.89 to 192.168.1.94 (192.168.1.88/29).
Client can connect to the second SSID but can't grab and IP address, what am I missing ?
View 6 Replies
View Related
Jun 28, 2012
We created the management interface, an internal DHCP scope in same subnet, and Two SSID tied to the same management interface:
- when we connect to the first SSID we have and IP address
- but when we connect to the secone SSID: impossible to get an ip address - auth and association are OK
View 11 Replies
View Related
Aug 10, 2011
I have a 5508 WLC controller at the HQ with the employee ssid ,the dhcp scope on the ssid is 10.120.0.0/16 network.
However,I want this same ssid to be brodcasted to a remote site using HREAP access point but with different dhcp scope 10.102.0.0/16.
I have tried creating another interface for the remote site with a different dhcp scope(10.102.0.0) but the controller wont allow me create another wlan with same ssid that existed before to apply the new interface created for.
View 1 Replies
View Related
Feb 28, 2013
i have two 5508 ver 7.3.0, one is the primary and one is the guest controller. mobility is up and running. i have an exising guest ssid working with wpa2-psk and web authentication and its working fine but i require a second guest ssid that only uses a wpa2-psk for ipod/ipads as i cant use passive client on primary controller. i presently have the one vlan range and dhcp setup on the guest controller to give addressing to either ssid. i know you can have multiple ssid setup on the guest controller but in other sites i have only had one guest connection comming from the primary controller, just a primary controller on each sites was only creating one link to the same guest controler.
View 3 Replies
View Related
May 17, 2011
We have a network of multiple WLCs: 5508, 4402, WISMs in two C6509 all running version 7 software. We have about a dozen SSIDs and we need to provide DHCP to the one public SSID (which like the other SSIDs span across all controllers) and to do so we thought of using a spare router, Linux workstation or DHCP server on the controllers. We are not sure if using the controllers is an option since we have multiple controllers. Is there a way to setup DHCP on a WLC and tell the others to use that WLC for DHCP for the one SSID?
View 3 Replies
View Related
Jul 10, 2012
Clarify some points with capwap implementation, does all data and control traffic tunneled back to the controller and switching packets to the specific vlan will be done by the controller? so if i have 5508 controller, its maximum throughput will be 8 gbps (local mode AP), provided i have done LAG on all its ports to the LAN switch?
View 2 Replies
View Related
Aug 26, 2012
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
View 4 Replies
View Related
Feb 12, 2013
I have an issue where I have an AP in one room and another in another.When I walk from one room to the other, I lose signal but manages to see the SSID and join.But, I cannot seem to surf the Internet, I have to manually disconnect and reconnect. Normal wireless routers I reconnect seamlessly without any manual disconnect & reconnect.Currently using cisco 5508 and ap2600.
View 8 Replies
View Related
Dec 12, 2012
we have two offices in same city at different location however we are planning to bring both the office at same location.Now lets say site A has controller 5508 configured with 24 AP's with 10.10.10.x subnet for internal SSID and Site B which is shifting to Site A campus has different subnet ( 10.10.20.x ) for same SSID.Site B has no controller since they had connection with H-reap and they were using different subnet for internal SSID ( 10.10.20.x ) .....Now i need to add their AP's in Site A controller which will be extended wireless LAN however we would like to keep same subnet ( 10.10.20.x ) what Site B has for wireless clients which is really confusing me ....I have already client subnet for site A with 10.10.10.x /24 subnet and nearly 200 users are already using this wireless client subnet.... How do i add their ( Site B ) subnet / 10.10.20.x with same SSID configured which is globally only one SSID ?
limitations :I can not create new SSID for site B since same will be broadcasting even in Site A AP's ?Is this possible to map one more subnet of site B to existing SSID with already different subnet ( 10.10.10.x ) ?
View 11 Replies
View Related
Dec 6, 2012
I have an issue where I cannot get clients to change SSID. I have two SSID, one WPA2 secure, one open guest. The secure is locally switched via Flexconnect and the guest is centrally switched. Both of them work. I have been able to test this and both work as intended. The problem is that once you connect to one of them, either secure or guest, you cannot then change to the other. The only way to change is to delete the dhcp entry from the scope and then do it.
Fast SSID change is enabled. I also have debug client output from when the client fails when you try to switch which I will include below. I also pulled some wireshark captures and those show me that the DHCP ack packets are trying to give the client the ip address from the incorrect/previous scope. So basically it's like FAST SSID change is not working and the client is never being disassociated properly??
I am totally stumped and even though the client will most likely not be switched between SSID that often I would still like to know the solution.
Cisco 5508 running 7.2.110.0
Cisco 3502 LWAPP
windows server 2008 dhcp server
[Code].....
View 5 Replies
View Related
Mar 28, 2013
I want to know how to configure ACL to have access to dhcp and web only.My router does not support tag vlan.
View 1 Replies
View Related
Jul 16, 2012
I am setting up a Cisco 5508 wireless controller and was looking for some feedback or assistance. Basically I already have my guest SSID configured and functioning. Created an interface group containing my vlans and applied the created ACL "Guest Policy - internet only", which is also working.I want to setup a second SSID called "staffstudent" and use RADIUS for authentication. I have already created two separate network policies on the radius server: staff and student. Each only allows certain user groups. I want to be able to differentiate on the controller side which profile they are logging in on and then apply the correct ACL. I have two currently configured: one for staff and one for student. It appears to me that since you have to apply the ACL at the interface level I cannot use both since my interface is accepting both staff and students. Is there a way I can filter them using RADIUS so that when they login RADIUS can return a "student" value and then apply the correct ACL? Same for staff?
View 2 Replies
View Related
Dec 12, 2012
is it possible to multicast between 2 different SSID's that are associated to 2 different VLAN's?
View 2 Replies
View Related
Jul 26, 2012
setup a WEP SSID on my 5508 controllers. THat being said, I have multiple sites with extremely old scan guns that only do 104bit wep. I plan on locally switching this SSID and using static WEP 104bit key with MAC authentication, and then ACLing to limit my inherent security issues/exposure once someone compromises my WEP key. [code]
View 4 Replies
View Related
Sep 26, 2012
On a wlc 5508-7.0.116, can I set up 2 ssids that map to one wlan/vlan/subnet. I thought you could but I don't have the means to test without breaking production.
My goal is this:
Ssid red open
Ssid blue wpa 2
But all clients on the same ip subnet
View 3 Replies
View Related
Jan 28, 2013
I have Build a 5508-HA Cluster (7.4.100.0) , hat to reboot this cluster due to Licens install.After the reboot atleast one of the SSIDs was not broadcasting anymore, even the checkbox was checked.
What did I do:
Installed the Licenses @ Freiday 12:00
@17:15 reload active WLC, wait till controller is up again (a few minutes pingable)
@17:25 force failover to first controller.
check a few SSIDs but not all, those who where check are ok.
@monday 07:00 clients complaining not seeing the SSID (some where connected)
View 6 Replies
View Related
Jul 27, 2012
on a 5508 WLC can we create new SSID for I PAD / IPHONE Users without having ISE, only I phone / I PAD are allowed to be authenticated rest all should be denied. IS this possible?
View 8 Replies
View Related
Jul 25, 2011
I have a wireless lan controller (5508) broadcasting 2 SSID's, once is a secure vlan grabbing an ip address from a local dhcp server and getting access to the internal network, and the other ssid is for a guest vlan where the dhcp server is in a remote site and internet access is off a circuit in our data center which is accessed over a wan. The secure ssid's vlan is defined on the local switch, but the guest vlan is not defined on the local switch.the ap's in the respective sites are trunked to the core switch and the switchport config is : [code] it's trunked b/c we have both vlans going across this physical connection.I would like get the guest vlan a wired connection, ie. off a switchhub, but not sure how to do that as this guest vlan is not defined on our local network.
View 1 Replies
View Related
Sep 4, 2012
I have an open SSID on 5508 controllers - configured as anchors and need to redirect wireless clients to the wireless help page automatically once they have connected and opened their browser.I've read all through the web auth and pass through discussions on here but nothing seems to be quiet right for me - unless I am completely missing something.
View 5 Replies
View Related
Nov 17, 2011
I have two WLC-5508 for 50 AP's deployed. One is primary controller & other is secondary.Recently noticed an unknown "authorization failed, no sufficient privileges for user" message poping up while making configuration changes in WLC. Specificly when trying to create an new SSID. WLC Authentication is local. This message poped up earlier once or twice but it didnt prevent from making changes that time.
View 3 Replies
View Related
Aug 28, 2012
My customer wants to have mapping of WLAN SSID with different authentication protocol as show below .
1: EMP-M for Mschap
2: EMP-G for Peap GTC
3: EMP-T for TLS
For example EMP-M SSID users should be connected with only PEAP(MSCHAPv2) and not on other methods like PEAP-GTC/EAP-TLS .
customer is currently having WLC 5508 and using ISE for AAA . Any tip how we can do the above requirement through WLC .
View 4 Replies
View Related
Apr 7, 2013
I have a 4400 and a 5508 WLC in the same location We want to be able to roam between ap joined to both the 4400 and the 5508 using only one ssid
Do I only need to create a mobility group and add both WLC then create only one WLAN on one of the controllers and it will be shared across bot WLC.
View 5 Replies
View Related
Sep 25, 2012
Setup a WAP321 with the new 1.0.1.10 firmware. Setup 2 SSIDS:
WIRELESS (vlan:1)
GUEST (vlan:99)
The wap is plugged directly into a port on my router so I configured the port and additional vlan99 port. I have a DHCP scope assigned on the router to both the port and port.99 interfaces.clients on WIRELESS have no problem and work correctly, however when a client joins guest...a packet capture on the router port shows that a dhcp request is being received for the same MAC on both untagged and tagged 99 interfaces....thus it appears the WAP is not handling the vlans properly
16:07:10.566932 PortA, IN: IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 84:c9:b2:78:fc:31, length 331
16:07:10.566947 PortA.99, IN: IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 84:c9:b2:78:fc:31, length 331
View 2 Replies
View Related
Feb 17, 2013
i' ve got 2 cisco 1130 AG AP's , i want both of them to broadcast 2 ssid's per AP, i've done so far but my clients cannot get a ip adress from the dhcp server.
View 19 Replies
View Related
Jun 13, 2012
I'm using a Cisco Wireless LAN Controller 5508, 14x Access Points 1041 and 6x Access Points 1031 in combination with a NCS 1.0.
Is it possible to broadcast SSID'S only on defined Access Points, e.g. AP 1-3,7-10,18? If yes, what have I to do?
View 8 Replies
View Related
Sep 15, 2011
Has anyone come accross a problem whereby an SSID becomes unavailable when selecting a Radio Policy of '802.11g Only'? The SSID is configured identically accross multiple controllers, but only works on the WISM's. The same WLAN profile on a 5508 is unavailable unless I select a Radio Policy of 'All'.
All controllers (WISM's and 5508's are running 6.0.188.0)The WLAN profile is using MAC Filtering[WPA2][Auth(802.1X)] as the security policy.
View 3 Replies
View Related
Feb 24, 2013
I have a cisco wlan controller (2100) running software 7.0.235.0. I have the internal private wlan running off of port 1 and that is working fine with an internal dhcp server.Is it possible to setup another ssid (guest) and have the interface directly linked to a static ip on the WAN and also use the built in cisco internal dhcp server?
View 4 Replies
View Related
Jun 11, 2013
We've encountered problem from the last few days with DHCP on certain SSID's. We have a wireless network with 13 SSID's being managed by a WLC 5508 pair configured as high availability (52 AIR-CAP3502I). Yesterday we encountered an issue with DHCP on a few of the SSID's but not all, and as a last resort a reboot of the controller fixed the problem. Statically assigning addressing allows for traffic to traverse the network out to the web and back so I don't think it's a VLAN configuration issue on the wired side. It's worth mentioning however that the controllers are configured for a LAG to HP switches. DHCP is being handled by an external windows DHCP server and the primary server address points to the gateway which has a relay configuration pointing to the windows server on the other side of it. Again, rebooting the controller fixed the problem and the web traffic traverses fine if statically assigning addressing.
View 1 Replies
View Related
Aug 22, 2011
The two controllers are having two internal DHCP servers with the same range in LAN (enx1,enx2). but i have specified which is primary DHCP server(enx3) in WLAN interface.
Now if a new user added into network, will he get IP address from primary dhcp(WLC) or AP connected WLC.
if two users connected to 2 diff AP's which are connected to 2 WLC will get the same IP address? since having same address pool configured.
View 11 Replies
View Related
Sep 16, 2012
I am having trouble getting DHCP working for a site connected using Flex Connect. Here is my setup. I have a single 5508 Controller at one site using the 10.3.0.0 network. All AP's at that site are in local mode and use the local DHCP server, 10.3.0.2. Everything works fine there. Each site uses a different SSID as well.
At my second site, 10.4.0.0, all AP's there connect back to the controller at the site above and are in Flex Connect mode. The AP's work fine and the clients work fine there but they get an IP address on teh 10.3.0.0 instead of the 10.4.0.0 network. If i setup the SSID at this site to override the DHCP server settings and tell it to use 10.4.0.2, which is our local DHCP server, the clients don't get an address at all.Is this simply a matter of setting an IP Helper address on the router where the WLC is located or is there more to it than that?
View 4 Replies
View Related
Dec 15, 2011
At customer site we have a wireless lan installed with wireless lan controller 5508. This works fine but the customer wants to add wireless bridge WET200 into the network. The problem is that the bridge seems to authenticate and associates with the LWAPP but does not get an ip-address.
View 5 Replies
View Related
