Cisco Wireless :: WLC 5508 Multicast Between SSID's And Vlan's
Dec 12, 2012is it possible to multicast between 2 different SSID's that are associated to 2 different VLAN's?
View 2 Replies
ADVERTISEMENT
Cisco Wireless :: To Verify Multicast With WLC 5508
Dec 25, 2012I used the wlc 5508 GUI to enable multicast in the CONTROLLER section, AP Multicast mode "Multicast" with a group address 239.1.1.1. Also in the "Multicast" section enabled Global Multicast Mode and IGMP Snooping.
My wired network is using a bsr and pim sparse-mode all around. My wlc is connected to a core 6513 L3 switch and on a neighbor L3 switch I can see a shared tree mroute entry and a source based entry for the wlc multicast group I created,
sh ip mroute
( *, 239.1.1.1 )
( 192.168.0.1, 239.1.1.1 )
I can't ping 239.1.1.1 though from anywhere, even the wlc's gui using the ping tool.I can do an ip igmp join on a loopback and ping from a neighbor device and get a reply.
In the monitor multicast section of the gui I can see some Layer2 MGID entries and one in the Layer3 MGID section but not for the 239.1.1.1 address.How do I verify my multicast over wireless setup is working correctly?
Cisco Wireless :: 5508 Assign Single Ssid To Multiple Interface Groups By Assigning Ssid To Multiple AP Groups
Aug 26, 2012Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
Cisco Wireless :: WLC 5508 Version 7.0 - Enabling Global Multicast Mode?
Apr 16, 2013I am using WLC 5508 version 7.0 facing issue while enabling global multicast mode .
client machine stops DNS resolution after some time once we enable global multicast mode on WLC .websites are opening with IPs but not with DNS names .
DNS resolution starts working immediately after disabling multicast mode on wlc .
Cisco Wireless :: 5508 Roaming From AP On Same SSID
Feb 12, 2013I have an issue where I have an AP in one room and another in another.When I walk from one room to the other, I lose signal but manages to see the SSID and join.But, I cannot seem to surf the Internet, I have to manually disconnect and reconnect. Normal wireless routers I reconnect seamlessly without any manual disconnect & reconnect.Currently using cisco 5508 and ap2600.
View 8 Replies View RelatedCisco Wireless :: 5508 / How To Map Two Different Subnets To One SSID
Dec 12, 2012we have two offices in same city at different location however we are planning to bring both the office at same location.Now lets say site A has controller 5508 configured with 24 AP's with 10.10.10.x subnet for internal SSID and Site B which is shifting to Site A campus has different subnet ( 10.10.20.x ) for same SSID.Site B has no controller since they had connection with H-reap and they were using different subnet for internal SSID ( 10.10.20.x ) .....Now i need to add their AP's in Site A controller which will be extended wireless LAN however we would like to keep same subnet ( 10.10.20.x ) what Site B has for wireless clients which is really confusing me ....I have already client subnet for site A with 10.10.10.x /24 subnet and nearly 200 users are already using this wireless client subnet.... How do i add their ( Site B ) subnet / 10.10.20.x with same SSID configured which is globally only one SSID ?
limitations :I can not create new SSID for site B since same will be broadcasting even in Site A AP's ?Is this possible to map one more subnet of site B to existing SSID with already different subnet ( 10.10.10.x ) ?
Cisco Wireless :: WLC 5508 Cannot Change SSID
Dec 6, 2012I have an issue where I cannot get clients to change SSID. I have two SSID, one WPA2 secure, one open guest. The secure is locally switched via Flexconnect and the guest is centrally switched. Both of them work. I have been able to test this and both work as intended. The problem is that once you connect to one of them, either secure or guest, you cannot then change to the other. The only way to change is to delete the dhcp entry from the scope and then do it.
Fast SSID change is enabled. I also have debug client output from when the client fails when you try to switch which I will include below. I also pulled some wireshark captures and those show me that the DHCP ack packets are trying to give the client the ip address from the incorrect/previous scope. So basically it's like FAST SSID change is not working and the client is never being disassociated properly??
I am totally stumped and even though the client will most likely not be switched between SSID that often I would still like to know the solution.
Cisco 5508 running 7.2.110.0
Cisco 3502 LWAPP
windows server 2008 dhcp server
[Code].....
Cisco Wireless :: WLC 5508 - Second DHCP Server For Second SSID?
Apr 22, 2012I have Internal DHCP Server configured on the Cisco WLC 5508 and all is working fine. DHCP Range is 192.168.1.100 to 192.168.1.245. Now I created another SSID but I want clients connecting to this SSID get specific IP's or from a specific range. WLC has no option to bind a DHCP pool to a specific IP so what I did I checked the option to "Override DHCP" and added the IP of my firewall WLC is connected to and setup a DHCP Pool on that firewall as 192.168.1.89 to 192.168.1.94 (192.168.1.88/29).
Client can connect to the second SSID but can't grab and IP address, what am I missing ?
Cisco Wireless :: 5508 Single SSID / Two ACLs
Jul 16, 2012I am setting up a Cisco 5508 wireless controller and was looking for some feedback or assistance. Basically I already have my guest SSID configured and functioning. Created an interface group containing my vlans and applied the created ACL "Guest Policy - internet only", which is also working.I want to setup a second SSID called "staffstudent" and use RADIUS for authentication. I have already created two separate network policies on the radius server: staff and student. Each only allows certain user groups. I want to be able to differentiate on the controller side which profile they are logging in on and then apply the correct ACL. I have two currently configured: one for staff and one for student. It appears to me that since you have to apply the ACL at the interface level I cannot use both since my interface is accepting both staff and students. Is there a way I can filter them using RADIUS so that when they login RADIUS can return a "student" value and then apply the correct ACL? Same for staff?
View 2 Replies View RelatedCisco Wireless :: 5508 Best SSID Practices For Really Old Devices On WEP
Jul 26, 2012setup a WEP SSID on my 5508 controllers. THat being said, I have multiple sites with extremely old scan guns that only do 104bit wep. I plan on locally switching this SSID and using static WEP 104bit key with MAC authentication, and then ACLing to limit my inherent security issues/exposure once someone compromises my WEP key. [code]
View 4 Replies View RelatedCisco Wireless :: 5508 - Internal DHCP / Two SSID?
Jun 28, 2012We created the management interface, an internal DHCP scope in same subnet, and Two SSID tied to the same management interface:
- when we connect to the first SSID we have and IP address
- but when we connect to the secone SSID: impossible to get an ip address - auth and association are OK
Cisco Wireless :: WLC 5508-7.0.116 / Multiple SSID To 1 WLan
Sep 26, 2012On a wlc 5508-7.0.116, can I set up 2 ssids that map to one wlan/vlan/subnet. I thought you could but I don't have the means to test without breaking production.
My goal is this:
Ssid red open
Ssid blue wpa 2
But all clients on the same ip subnet
Cisco Wireless :: 5508-HA / SSID Not Broadcasting After Reload
Jan 28, 2013I have Build a 5508-HA Cluster (7.4.100.0) , hat to reboot this cluster due to Licens install.After the reboot atleast one of the SSIDs was not broadcasting anymore, even the checkbox was checked.
What did I do:
Installed the Licenses @ Freiday 12:00
@17:15 reload active WLC, wait till controller is up again (a few minutes pingable)
@17:25 force failover to first controller.
check a few SSIDs but not all, those who where check are ok.
@monday 07:00 clients complaining not seeing the SSID (some where connected)
Cisco Wireless :: 5508 - SSID For IPad / IPhone
Jul 27, 2012on a 5508 WLC can we create new SSID for I PAD / IPHONE Users without having ISE, only I phone / I PAD are allowed to be authenticated rest all should be denied. IS this possible?
View 8 Replies View RelatedCisco Wireless :: AIR-AP1141N-E-K9 / Can Use Multi SSID Without VLAN
Dec 27, 2012I'm using access point AIR-AP1141N-E-K9 and want to use Multi SSID. Based on Cisco document, when I config Multi SSID in access point, each SSID have a separate VLAN, is it a must have ? Can I use multi SSID without VLAN ?
View 5 Replies View RelatedCisco Wireless :: WRVS4400N How To Separate SSID By Vlan
Aug 10, 2011I have a WRVS4400N that broadcasts two different SSIDs. One is a public network and the second is a private network. Right now, both SSIDs are pulling from the same DHCP server, but I would like to separate the public from the private. How can I separate these SSIDs by vlans? I can't seem to get the vlans to route to separate ports.
This is my vlan settings. I have two DHCP servers right now. One is in an isolated network plugged into Port 3 of the WRVS4400N. The other is on the production network, plugged into port 1 of the WRVS4400N. For some reason, whenever I connect to SSID Public, it won't pull an IP from the DHCP on port 1, it only pulls it from the one on port 2.
I know there is three SSIDs here, the Static one is going to be the same network as the EMS one.
Cisco :: 5508 How To Grant Wire Access To A Wireless Ssid
Jul 25, 2011I have a wireless lan controller (5508) broadcasting 2 SSID's, once is a secure vlan grabbing an ip address from a local dhcp server and getting access to the internal network, and the other ssid is for a guest vlan where the dhcp server is in a remote site and internet access is off a circuit in our data center which is accessed over a wan. The secure ssid's vlan is defined on the local switch, but the guest vlan is not defined on the local switch.the ap's in the respective sites are trunked to the core switch and the switchport config is : [code] it's trunked b/c we have both vlans going across this physical connection.I would like get the guest vlan a wired connection, ie. off a switchhub, but not sure how to do that as this guest vlan is not defined on our local network.
View 1 Replies View RelatedCisco Wireless :: 5508 - Any Simple Way To Do URL Redirect On Open SSID
Sep 4, 2012I have an open SSID on 5508 controllers - configured as anchors and need to redirect wireless clients to the wireless help page automatically once they have connected and opened their browser.I've read all through the web auth and pass through discussions on here but nothing seems to be quiet right for me - unless I am completely missing something.
View 5 Replies View RelatedCisco Wireless :: WLC-5508 Authorization Failed To Create SSID
Nov 17, 2011I have two WLC-5508 for 50 AP's deployed. One is primary controller & other is secondary.Recently noticed an unknown "authorization failed, no sufficient privileges for user" message poping up while making configuration changes in WLC. Specificly when trying to create an new SSID. WLC Authentication is local. This message poped up earlier once or twice but it didnt prevent from making changes that time.
View 3 Replies View RelatedCisco Wireless :: 5508 - Same SSID With Different Dhcp Scope On Same Controller
Aug 10, 2011I have a 5508 WLC controller at the HQ with the employee ssid ,the dhcp scope on the ssid is 10.120.0.0/16 network.
However,I want this same ssid to be brodcasted to a remote site using HREAP access point but with different dhcp scope 10.102.0.0/16.
I have tried creating another interface for the remote site with a different dhcp scope(10.102.0.0) but the controller wont allow me create another wlan with same ssid that existed before to apply the new interface created for.
Cisco Wireless :: WLC 5508 - Mapping SSID With Authentication Protocol
Aug 28, 2012My customer wants to have mapping of WLAN SSID with different authentication protocol as show below .
1: EMP-M for Mschap
2: EMP-G for Peap GTC
3: EMP-T for TLS
For example EMP-M SSID users should be connected with only PEAP(MSCHAPv2) and not on other methods like PEAP-GTC/EAP-TLS .
customer is currently having WLC 5508 and using ISE for AAA . Any tip how we can do the above requirement through WLC .
Cisco Wireless :: 5508 - Mobility Group Same Ssid Multiple WLC
Apr 7, 2013I have a 4400 and a 5508 WLC in the same location We want to be able to roam between ap joined to both the 4400 and the 5508 using only one ssid
Do I only need to create a mobility group and add both WLC then create only one WLAN on one of the controllers and it will be shared across bot WLC.
Cisco Wireless :: WLC 5508 - AP LWAPP With 2 SSID / DHCP Differences?
Jul 22, 2012I need raise a especial configuration to 34 APs LWAPP associated to WLC 5508 with IOS 7.0.220
This is the Scenario:We have 34 APs LWAPP with 2 SSID (Corporative & Guest), with 2 DHCP different. The Guest SSID receive IP to DHCP from WLC while SSID Corporative receive IP from Microsoft DHCP. The AP On Site are Local and the Foreign AP are configured like H-REAP (H-REAP Local switching and Learn Client IP Address are marked)
Here is the thing, I need configure a new WLAN (Pruebas) for add to 34 APs (Local and Foreign) but this new WLAN must be receive IP from a New Microsoft DHCP
Firstly I configured a new Physical interface and linked to New WLAN (Pruebas) however i don't know how configure the AP and the DHCP because I want that the AP deliver IP addresses depending the Locality.The last because the SuperScope from DHCP is divided in various subnets and because the IP from the AP will be in another VLAN
Cisco Wireless :: 5508 - Broadcast SSID Only On Defined Access Points?
Jun 13, 2012I'm using a Cisco Wireless LAN Controller 5508, 14x Access Points 1041 and 6x Access Points 1031 in combination with a NCS 1.0.
Is it possible to broadcast SSID'S only on defined Access Points, e.g. AP 1-3,7-10,18? If yes, what have I to do?
Cisco Wireless :: 5508 Second Guest SSID On Controller Not Giving DHCP Out
Feb 28, 2013i have two 5508 ver 7.3.0, one is the primary and one is the guest controller. mobility is up and running. i have an exising guest ssid working with wpa2-psk and web authentication and its working fine but i require a second guest ssid that only uses a wpa2-psk for ipod/ipads as i cant use passive client on primary controller. i presently have the one vlan range and dhcp setup on the guest controller to give addressing to either ssid. i know you can have multiple ssid setup on the guest controller but in other sites i have only had one guest connection comming from the primary controller, just a primary controller on each sites was only creating one link to the same guest controler.
View 3 Replies View RelatedCisco Wireless :: 5508 Cannot Connect To An SSID When Restircting The Radio Policy
Sep 15, 2011Has anyone come accross a problem whereby an SSID becomes unavailable when selecting a Radio Policy of '802.11g Only'? The SSID is configured identically accross multiple controllers, but only works on the WISM's. The same WLAN profile on a 5508 is unavailable unless I select a Radio Policy of 'All'.
All controllers (WISM's and 5508's are running 6.0.188.0)The WLAN profile is using MAC Filtering[WPA2][Auth(802.1X)] as the security policy.
Cisco Wireless :: Configure Multiple VLAN On Single SSID In 1142N
Apr 2, 2013I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
Cisco Switches :: SG300- Use Multicast TV VLAN?
May 10, 2013I want to use Multicast TV VLAN with my SG300-10 to join Multicast Groups in different Data VLAN's. It's working fine, but the problem is that it isn't possible to add all the Multicast Groups to the Multicast VLAN because each TV channel use other groups. For me it's only to handle if I can use wildcards to add a specific range of multicast traffic to the Multicast TV VLAN. Is that possible with that Switch?
View 1 Replies View RelatedCisco Wireless :: 2112 One Ssid To Multiples Vlan Without Hreap Flex Connect
May 22, 2013I have one cisco wlc 2112 with ios 7.0.230.0 with license to support 12 access points. My access points are nine (9) lap1231ag and one (1) lap1310.I just have one wlan (ssid). My scenario of deployment is in layer 3. I have one interface management and ap manager in the WLC. All my Access Points have differents ip address that WLC. I need to configure a unique ssid to associate my six (6) dynamics interfaces (each dymanic interface with different vlan subnet).Each wlan profile (ssid) should have the same security in phase 2 (wpa2/psk). My cisco access points don't support hreap. My wlc support only (4) interface into an interface group, and i need six (6) dynamics interfaces.
View 6 Replies View RelatedCisco Switching/Routing :: Multicast On 886VA VLAN?
Oct 28, 2012I'm trying to configure multicast between 2 VLANs on a Cisco 886VA running IOS 15.2 (3) T1 (advanced security). While I can set the global "ip multicast-routing" I cannot "ip pim sparse-mode" on my interfaces - ip pim is actually unknown and also doesn't appear in the interface's ip subcommand list when using "?".
The feature navigator says pim is supported on my platform and IOS version.
My config looks like this:
interface FastEthernet3
switchport access vlan 103
no ip address
[Code].....
Cisco :: 5508 - Error Messages / Receive Multicast Queue Is Full On Controller
Jan 25, 2012I'm starting to see an error creep up that I havn't seen since 2003/2004 on my brand new 5508 controllers. I'm recieving the following from my WCS: Receive Multicast Queue is full on Controller and then on the controller itself RX Multicast Queue Full. I understand this used to be due to a large influx of ARP requests or CDP packets on older controllers but, this was supposed to be fixed in an update many years ago.
Has seen this on their 5508's. These were advertised as having the horsepower to handle our user loads which arn't really that high at 300 users at any given time max.
Cisco Firewall :: 6513 Switch - Multicast Inside A Single VLAN In FWSM
Dec 6, 2009I am trying to make the multicast working between few hosts inside a single vlan. Host are running mysql cluster and Multicast is used to send master/slave status information to the IP 228.10.10.10 on port 45566.The vlan is defined in FWSM and the host are connected via the core-switch(6513). (hosts-->core-sws--->fwsm)I have tried searching the documentation, but couldn't find specific info to enable multicast between hosts residing in same vlan. FWSM is running code 3.1(4). since the hosts are residing in the same vlan, I am thinking of applying the <multicast-routing> just for that SVI in FWSM.
View 6 Replies View RelatedCisco Wireless :: 5508 WLC In HA Over L2 VLAN
Nov 13, 2012I am very interested in the new 7.3 feature HA.Also I can read that it is recommended to connect the two WLCs directly. How to use a L2-VLAN between them, in fact to bridge a distance between two data centres?
View 3 Replies View Related