Cisco Wireless :: 1200 DAS Mobile Access 2000 Doesn't Support
Apr 2, 2012
The client currently has DAS solution integrates with cisco ap1200 which has been eos. As per my knowledge DAS mobile access 2000 doesn't support. 802.11n, is this correct? We are planning to separate the dad environment with cisco. Basically positioning new 3600 n indoor AP to replace existing eos 1200. What are the pro and cons of separating two brands and solutions? Other cabling.The client having coverage issue and adding an amplifier and cable loss may add more issues to existing environment.
Also, based on experience 80211n AP are required is higher density vs 1200.What are your thoughts or best design option to separate das from WLAN environment?
I need to change providers from Verizon to AT&T. This modem came with the AT&T Sim card installed in my notebook. The software (Dell Mobile Broadband Utility Help) says " Choose Network Selection from the Settings Menu. Select AT&T and click Load." Unfortunately, Network selection is not an option.
How do I do it? This modem is compatible with Verizon, AT&T and Sprint networks.
We just upgraded to ASA 8.4.4.1 and the latest CSD image, 3.6.6203. We currently have a DAP set up to scan one group policy for a secific AV but wanted to start implementing this for all group policies and including several different flavors of AV (so anyone could connect from anywhere as long as a pre-approved AV is installed). We are going to allow about 20 different versions of different AV's and I've tested a couple already and they're successful.
My issue right now is trying to allow (or deny) AV that is installed on an Android tablet (and potentially Apple devices). The tablet has avast Mobile Security installed, and even if I select Vendor: Alwil as a whole, it still does not recognize it and denies the user. I have tested on a PC and it works fine. Is there something that I am missing or are mobile AV programs not included in the DAP policies? Is this going to be considered for future versions of CSD or ASA or are we going to continue to consider Android and Apple devices "secure" and not in need of an AV?
if vPC is supported between a single 2232PP FEX and two 7000 switches running 6.0(1)? I have been researching this for an implementation I am doing for a client and was able to determine it was not supported with earlier versions of 5.0 when the FEX is connected via vPC as I described above, but I can't find anything related to version 6.0(1). I have done this for other clients with 5000 and 2000 switches, but I don't have too much experience with 7000 switches.
I've got an iPad2, which works without issue at home (1130 AP/ASA5505), but at my office, we have a 1200 series AP. It's hit and miss, but other people who bring iPads in have noticed the same issue--our internal SSID is non-broadcast. Even though the SSID is previously configured and works on occassion, there are times where it won't even see the SSID at all to connect.
This happens with iPad and iPad2, iOS4 and iOS5...
LIke i said, works fine on my non-broadcast SSID at my home on an 1130 AP...
Is it possible to setup a Cisco 1200 AP with 802.1x to drop users into the corprate network if they have a certificate or if not to put them on the guest network?
I recently purchased a Ciso 1200 Series WAP and I want to bridge this to my existing Cisco Wireless Router So I can extend my coverage. I have done some research but keep coming up short as to where I need to start. Note*(I do not want a physical connection to the WAP, I simply want to be able to bridge the connection from my existing Wireless router to my WAP.
I have a cable broadband installed in my home i just bought cisco 1200 series access point...now how to configure my access point. I believe I have to plugged fastethernet cable coming out of my cable modem to access point after that? What I have to do ....do I have to configure the cable modem as wlel or not???
We recently acquired a 4404 Cisco controller for our network and have been adding our 1200 and 1130 Access points to the controller.This was accomplished by upgrading the APs to LWAPP and then they would automatically be discovered by the controller and then join. Lately, new 1131 APs that have undergone the same process, are not joining the controller. They are discovered but then the close the connection. We are running a flat network so all devices are in the same subnet.Software Version of the controller 6.0.188.0. [code]
I has 4 VLANs and I want a MAC address has access to a VLAN, but not to another.
I used ACLs, but this will block the access to the access point, How to get the mac address will have access to a VLAN, eg no other Vlan? I has 4 VLANs and I want a MAC address has access to a VLAN, but not to another.
I used ACLs, but this will block the access to the access point, How to get the mac address will have access to a VLAN, eg no other Vlan?
What's the best design and configuration to deploy some fixed access points (wired) and others on a mobile truck (no wired)?I was thinking about configure the Wireless network using Mesh, but could not find much information about the convergence time when MAP (access point on the mobile truck) finds a better RAP signal, not sure if the clients would keep the conection up when the MAP converge.The customer have 11 3502e access points and 1 2504 WLC.Found out that 3502e does not support autonomous mode, so can not use autonomous bridge mode that has some mobile station configuration available.
The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
I'd like to configure ASDM access to ASA-SM using RSA SecurID authentication.I've followed instructions in this documen [URL]When I test access from CLI everything looks fine:
asa-vss/admin/act# test aaa-server authentication RSA Server IP Address or name: xx.xx.xx.xx Username: testuser Password: ********** INFO: Attempting Authentication test to IP address <xx.xx.xx.xx> (timeout: 12 seconds) INFO: Authentication Successful
[code]....
When I try to use ASDM, I'm unable to login and I can see lot of authentication error (Token reuse) messages on RSA server monitor window.It looks like ASDM 6.5(1) for ASA-SM doesn't support RSA/SDI authentication.
I have decided to buy a new wireless N enabled wireless router after my house was cleaned out by some robbers. After a long investigation I decided on the D-link DIR 655 as it suited my basic needs the best and since I haven't decided on a broadband supplier yet this should sort any and all possibilities no matter what I choose...
After an equal amount of investigation I decided on a HSPA+ USB dongle only to find that the router does not support the network I have purchased it on. It thenalso seems that it doesn't support the E1820 Huawei dongle either... so fine... I go and buy a Huawei D105 tht should technically be able to connect via the WAN port and would act as an internet gateway. Brilliant.
Now I have tried everything.... static IP on the D105 with a static IP setup on the 655. Connects fine... according to the web interface but NO INTERNET. When I connect my laptop directly to the 105 via CAT5 it works beautifully. DHCP on the D105 with the same on the 655. Connecting... Establishing Link (Please Wait...) FOREVER without ever getting an IP on the 655 (according to the web interface again) ... must be the D105 thats faulty so again plug in the laptop and within milliseconds the IP is assigned and Internet is blazing along again.... The D105 is not Wireless N so I cannot use it as my primary AP and only allows 5 simultaneous wireless connections (that is reserved for my cellphones). Why should I anyway?? the DIR655 should work fine....
Even after having taken it to D-link support at huge cost and effort I still don't have a working rig.... Seems the consultant plugged the D105 straight into the LAN on the 655 and then set his laptop to the same static range to get it to work... SURPRISE - I know that works since plugging the laptop straight into the 105 does the same thing.... But this is not what I want... I want my 655 to be the primary DHCP server for my network and control the allowed workstations that are allowed access to the internet with a working gateway. Bridging is apparently also not an option as that option has been removed so I cannot even bridge my main subnet onto the D105's internet sbnet... What am I to do....
If the 655 3G setup supported more than 2 dongles I might hve been able to use that and not spend anouther R600 on the D105, if the WAN port actually worked in either static or DHCP modes with the D105 that also would have solved the problem and lastly if all else fails and there was still bridging I could hack my own setup together to do what I want. Seems like I was wrong in selecting the D-link product.
Then to make matters worse I find another product with double the features online for half the price that integrates the 3G capability into the route and support more than 2 different models. including all the new Huawei dongles....
I've discovered that the DDNS update client in the RV042G does not support passwords that contains spaces. This is the first router I've run into that didn't like it.
There is a vlan Finance in my office. The requrement : Vlan Finance is allow to access internet and selected host/network and not allow to access internal network. But from internal network can access to Vlan Finance (Full access). I want to configure using Reflexive ACL, but from Datasheet 4500 doesn't support Reflexive ACL. Intervlan routing is in 4500. Is there any ACL configuration to support my requirement without using Reflexive ACL?
I just bought a Netgear Router WNR 2000 v3 and installed it. I got inside the router and could set up a Network Name and security key. However, I can not access the internet when I chose a security password using WPA 2, WPA-PSK + WPA 2 PSK, or WPA/WPA 2. It only accesses the internet when I chose None.( no secured ).At this time, my network is unsecured because there isn't way I can access the internet when I create a security key using the 3 options the router offers.
Note : I have tried the 3 security options creating a key number and my computer connect to the wireless network but don't access the internet. It only access the internet when I select None ( no secured )
We have 10 ADSL lines and 5 of them goes in the load balancer (One gateway) and the rests are used as default gateways for internet access. We use ADSL routers as access points for internet, but those routers should be part of our network and should be given an address in order for them to act as default gateways for internet access. I'm facing a real prob with the ADSL routers Linksys WAG54G2 because they doesn't support a subnet mask 255.255.0.0 Any recommendation for an ADSL router model that support a netmask 255.255.0.0 ?
My cisco 2811 router interface configuration ip address: 172.20.0.1 255.255.254.0.Load balancer output lan ip address: 172.20.0.5.My ADSL routers will be in the following range : 172.20.0.6 - 172.20.0.10
If switches on a network doesn't support remote port mirroring and only local port mirroring, What are the options to still capture all the traffic from all switches on 1 single core switch?
Region : Finland Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : 3.14.2 Build 120822 rel.577775n ISP : saunalahti
dosen't support my huawei E392 4G modem. if possible would you make bin for this. there is not other modems that you can get for 4G connections from the service provider so it would be nice if there was more compatibility than some old ancient modems. starts to feel like this is been sold as 4G router and dosen't actually support that at all.
We have a customer that has a fiber rum between 2 building. They want to have 2 seperate fibers active that terminate into the same switch on each end. (redundancy).
In building A they have an extreme networks black diamond switch that does not support STP.In bulding B they have a Cisco 4507.
We will ahve to use a layer 3 routed connection due to the fact their switch in building A does not support STP.Our tech does not want to use static route becuase he does not want to setup IP SLA for the redundant connection.
Will RIPv2 work for this scenario and failover to the other fiber if needed? The hop count is the same for each fiber path..
My client has a PC that can use a SIM card to gain access to the internet. They have an ASA5540 and are running IPsec VPN.
When accessing the VPN while the PC connects to the internet via use of the SIM card, he connects successfully to the VPN but is unable to access anything on the internal network. If he connects to the internet using wireless or wired, he connects successfully to the VPN and is able to access everything on the internal network.
Is this a limitation of the Cisco VPN Client? Perhaps something missing in the configuration? Or do they still require the mobility license (though I thought that was only for AnyConnect)?
I have a WLC 4402 on my network. Recently mobile phones can connect to the wireless network and obtain a valid IP address. This IP is pingable from a workstation anywhere else on the network. However, these phones will not display web pages. They come up page cannot be displayed. I even tried putting Google's IP address in the phone's browser and it still did not display. I can connect through the same WLAN via a laptop or iPad. These devices have no problem displaying web pages. I even went ahead and created a new TESTWLAN with no encyption but to no avail. Same results: laptops connect and display web pages and smart phones connect, gain IP but do not display web pages. Comes up page cannot be displayed. This matters not whether its an iPhone or Android platform.
I want to use my PC for internet access in my office (shed)Shed does not have phone line or cable points.PC does not have wireless capability.Moile phone can be used as Access Point (but PC can't detect it- no wireless capability)What is the methods to provide plug-in/ bolt-on wireless capability for my PC so that it can use my mobile Access Point to connect to the internet?
We have a 1200 Aironet just go down hard for no reason through out the day, we replaced the Power Injector with a C2960 POE Switch, we also replaced the cabiling. When it goes down hard all three lights are still green as if the AP is still up. We verified the IOS with other stores and everything is the same on the configurations, versions, and IOS.
I got my final assignment from school, and my teacher asked me to configure 2 Access Points (1200 series) directly on a Wireless Controler (Cisco 2106). I can't ask my teacher for any questions, cause he doesn't know how to configure it also, THAT's why he's asking me to do it.I've learned a lot of things about the default static interfaces (the "management" and "ap_manager" interface), but i can't seem to fully understand how to configure it.I want to use the Internal DHCP server of the WLC. How I can get those 2 Access Points working on the WLC. I only seem to get DHCP issues.
This is what i've done:
- Leave the configuration of the "management" and the "ap_manager" default (172.16.1.30 and 172.16.1.30). Bound to port 1
- Made a new interface "AP1" with IP-Address 10.0.0.10 (/24), default gateway 10.0.0.1. Primary DHCP server: 172.167.1.30
- Made a new interface "AP2" with IP-Address 192.168.1.10 (/24), default gateway 192.168.1.1. Primary DHCP server: 172.167.1.30
- Made 2 DHCP scopes within the 192.168.1.0 and 10.0.0.0 networks.
For some reason, when i boot up both AP's, the won't get any DHCP address.
I am looking at deploying a Cisco Virtual Wireless LAN Controller (vWLC 7.3).Do I need Prime Infrastructure to manage the environment, or can I manage my AP's (1200 series) using the vWLC alone?
I want to disable the MAC authentication that is configured in my Aironet 1200 Cisco Access Point, now set to "Local list only". I want that any wireless device can connect if the user knows the wep password.
I cannot find the option to disable the MAC authentication.
