Cisco Wireless :: 3502e Mobile Access Point Using Mesh
Nov 1, 2012
What's the best design and configuration to deploy some fixed access points (wired) and others on a mobile truck (no wired)?I was thinking about configure the Wireless network using Mesh, but could not find much information about the convergence time when MAP (access point on the mobile truck) finds a better RAP signal, not sure if the clients would keep the conection up when the MAP converge.The customer have 11 3502e access points and 1 2504 WLC.Found out that 3502e does not support autonomous mode, so can not use autonomous bridge mode that has some mobile station configuration available.
View 5 Replies
ADVERTISEMENT
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Sep 27, 2011
I mis-ordered some 3502i’s . They came with Mesh image by accident.
Can I just setup DHCP Option 43 TLV to point to my WLC, plug the AP in and have it change from Mesh to LWAP?
How do I switch from Mesh to LWAP without touching console?
View 6 Replies
View Related
Jan 21, 2013
A 1552E has a temperature gauge sensor connected to its power over Ethernet port. the port status shows line protocol as down.The cable from 1552 to the sensor has been changed twice. We can see the 1552E gig1 interface is at 1000full duplex. Is there any chance the speed is causing the problem here. it seems the 1552E doesn't allow to set different speed & remains on 1000.
View 2 Replies
View Related
Sep 28, 2012
I want to use my PC for internet access in my office (shed)Shed does not have phone line or cable points.PC does not have wireless capability.Moile phone can be used as Access Point (but PC can't detect it- no wireless capability)What is the methods to provide plug-in/ bolt-on wireless capability for my PC so that it can use my mobile Access Point to connect to the internet?
View 2 Replies
View Related
May 17, 2012
I have installed 4 of these units in a commercial premises offering free wifi. Since the day they were installed (5Months ago) we had connectivity issues with mobile devices. This was somewhat resolved in the latest FW 1.0.04 but we are still having random disconnections on the units every 2 - 4 days and have to reboot the units. Lately the units have become unresponsive and reset themselves back to factory settings.
What we have done so far:
Changed router models - No change
Changed from Static IPs & DHCP - No change
Turned on isolation - No change
Performed a wifi analysis to pick the best channel for each unit - Slight signal gain but still disconnects
Changed to 20Mhz only (And all other variations) - No change
I think I am left with no option but to return these for some other brand. I'm really regretting buying these units at the minute...
View 8 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Apr 11, 2013
By default, 802/11a/n is set for backhaul communication.Does that mean that if most of my clients are on 5ghz, Mesh network is not a preferred design to go? Reason being:- client communication on a/n radio might disturb the traffic of the whole cell and of all the MAPs that connect to the network through that MAP.
View 6 Replies
View Related
Feb 21, 2013
When I tried to download software for WLC44xx, I noticed both mesh and standard software releases. Do I need to keep seperate controller for mesh APs?.
WLC with standard sw can not handle mesh APs?
View 6 Replies
View Related
Aug 21, 2012
I worked in an University, and we have a deployment of 300 AP, but recently we bought 15 AP 3502e model, with this antennas:
AIR-ANT2460NP-R
Azimuth 3dB Beamwidth
#80 degrees
#Elevations 3dB Beamwidth
[Code].....
My question is, when i try to position this new APs on a certain map, what should i put on the Azimuth and Elevation degrees parameter? The degrees that comes in the product data sheet above, or it depends on how the antennas are installed?.
View 14 Replies
View Related
Mar 22, 2013
I am still new to wireless. I have been studing for my CCNA Wireless for about 6 months now so I still have a lot of questions.
Right now I have to deploy some new APs. We are using 3502e APs. I have a qustion on how to mount antennas for these access points. I have to make a mounting bracket the new installations. What was done with the previous APs was to mount a unistrut beam to an I beam in the building. There is 2 AIR-ANT-1728's and 2 AIR-ANT-5160V-R antennas mounted straight out on the unistrut. Then they put a T bracket on the unistrut and mounted a second bar 90 degrees from the main bar and connected the third 1728 and 5160 antennas on the second mounting bracket. So we have 4 antennas in a row, and two off to the side 90 degrees from the other 4 antennas.
My question, is this OK to have them this way, or would it be better to have all 6 antennas in a straight line when I fabricate my new AP brackets?
Here is a picture of what I am talking about. This would be looking at it from above.
Current New Proposal
__________o__o__o__o_ _________o__o__o__o__o__o
| AP AP
|
|o
|
|o
View 7 Replies
View Related
Sep 5, 2012
The 3502e has 3 antenna terminals for each band. Is the order of connection to the antenna pigtails significant? The antenna pigtails are not marked ABC (just blue boots for 5GHz.)
View 2 Replies
View Related
Mar 28, 2012
We purchased some 3502e's and I was told we could set them up as automous ap's to do a site survey. however i haven't come across much online for instructions. i saw one post that mentioned downloading code for another ap model - i think a 1260, but we don't have rights for such a download.
View 11 Replies
View Related
Sep 5, 2012
The 3502e has 6 antenna connections, 3 for each band, 5GHz band is marked in blue. The antenna pigtails are only marked with the matching color - 3 blues or 3 blacks. No A,B or C. Does it matter which pigtail goes to which of the 3 terminals so long as the band is correct?
View 1 Replies
View Related
Apr 11, 2013
I am in the process of installing a new wireless network in our offices and I was wondering if I can add an extension to the cable that connects my AIR-ANT-1728 to my AIR-CAP-3502e AP to get better coverage in our offices?
View 4 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Feb 20, 2013
A few months ago we upgraded our warehouse from 1242 APs to 3502E APs. We changed 16 units, all in the same building. When we came in the next day we found out that they were all on channel 1 at their lowest power level. The WLC was set for auto negotiate for power and channel but for some reason it did not work. We had successfully changed they rest of the factory with the auto feature enabled but for some reason, the warehouse did not work properly. All APs have the same IOS and are they same model. We have WiSMs mounted in a 6509 chassis as our WLC.
View 1 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Apr 2, 2012
The client currently has DAS solution integrates with cisco ap1200 which has been eos. As per my knowledge DAS mobile access 2000 doesn't support. 802.11n, is this correct? We are planning to separate the dad environment with cisco. Basically positioning new 3600 n indoor AP to replace existing eos 1200. What are the pro and cons of separating two brands and solutions? Other cabling.The client having coverage issue and adding an amplifier and cable loss may add more issues to existing environment.
Also, based on experience 80211n AP are required is higher density vs 1200.What are your thoughts or best design option to separate das from WLAN environment?
View 6 Replies
View Related
Aug 25, 2011
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
View Related
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
Apr 6, 2011
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies
View Related
Feb 10, 2012
I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies
View Related
Dec 3, 2011
I want to PAT my project of WLAN and i attached the document, how I create the Testing Criteria of the said scenarios, PAT document includes WCS 7.0, WLC 5508, MSE 3310, Cisco AP 3502e and ACS 4.2.
View 0 Replies
View Related
May 9, 2012
I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
View 10 Replies
View Related
Jun 4, 2013
I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.
View 11 Replies
View Related
