The 3502e has 3 antenna terminals for each band. Is the order of connection to the antenna pigtails significant? The antenna pigtails are not marked ABC (just blue boots for 5GHz.)
View 2 RepliesThe 3502e has 6 antenna connections, 3 for each band, 5GHz band is marked in blue. The antenna pigtails are only marked with the matching color - 3 blues or 3 blacks. No A,B or C. Does it matter which pigtail goes to which of the 3 terminals so long as the band is correct?
View 1 Replies View RelatedI am in the process of installing a new wireless network in our offices and I was wondering if I can add an extension to the cable that connects my AIR-ANT-1728 to my AIR-CAP-3502e AP to get better coverage in our offices?
View 4 Replies View RelatedI am still new to wireless. I have been studing for my CCNA Wireless for about 6 months now so I still have a lot of questions.
Right now I have to deploy some new APs. We are using 3502e APs. I have a qustion on how to mount antennas for these access points. I have to make a mounting bracket the new installations. What was done with the previous APs was to mount a unistrut beam to an I beam in the building. There is 2 AIR-ANT-1728's and 2 AIR-ANT-5160V-R antennas mounted straight out on the unistrut. Then they put a T bracket on the unistrut and mounted a second bar 90 degrees from the main bar and connected the third 1728 and 5160 antennas on the second mounting bracket. So we have 4 antennas in a row, and two off to the side 90 degrees from the other 4 antennas.
My question, is this OK to have them this way, or would it be better to have all 6 antennas in a straight line when I fabricate my new AP brackets?
Here is a picture of what I am talking about. This would be looking at it from above.
Current New Proposal
__________o__o__o__o_ _________o__o__o__o__o__o
| AP AP
|
|o
|
|o
I worked in an University, and we have a deployment of 300 AP, but recently we bought 15 AP 3502e model, with this antennas:
AIR-ANT2460NP-R
Azimuth 3dB Beamwidth
#80 degrees
#Elevations 3dB Beamwidth
[Code].....
My question is, when i try to position this new APs on a certain map, what should i put on the Azimuth and Elevation degrees parameter? The degrees that comes in the product data sheet above, or it depends on how the antennas are installed?.
I'm looking for a router with an external antenna connection so I can attach an outside antenna to extend my wi-fi signal signal around my farm.Right now I have Hughes net internet service running to a Belkin 750 router, which is descent around the house, but has no connection for an external intenna.
View 3 Replies View RelatedWe purchased some 3502e's and I was told we could set them up as automous ap's to do a site survey. however i haven't come across much online for instructions. i saw one post that mentioned downloading code for another ap model - i think a 1260, but we don't have rights for such a download.
View 11 Replies View RelatedI have to replace our WRT54G router--it's currently connected to a power booster and and omni-directional antenna. Is there a router with an antenna connection compatible with the WRT54G--preferably a single antenna model?
View 4 Replies View RelatedWhat's the best design and configuration to deploy some fixed access points (wired) and others on a mobile truck (no wired)?I was thinking about configure the Wireless network using Mesh, but could not find much information about the convergence time when MAP (access point on the mobile truck) finds a better RAP signal, not sure if the clients would keep the conection up when the MAP converge.The customer have 11 3502e access points and 1 2504 WLC.Found out that 3502e does not support autonomous mode, so can not use autonomous bridge mode that has some mobile station configuration available.
View 5 Replies View RelatedA few months ago we upgraded our warehouse from 1242 APs to 3502E APs. We changed 16 units, all in the same building. When we came in the next day we found out that they were all on channel 1 at their lowest power level. The WLC was set for auto negotiate for power and channel but for some reason it did not work. We had successfully changed they rest of the factory with the auto feature enabled but for some reason, the warehouse did not work properly. All APs have the same IOS and are they same model. We have WiSMs mounted in a 6509 chassis as our WLC.
View 1 Replies View RelatedI want to PAT my project of WLAN and i attached the document, how I create the Testing Criteria of the said scenarios, PAT document includes WCS 7.0, WLC 5508, MSE 3310, Cisco AP 3502e and ACS 4.2.
View 0 Replies View RelatedI got a different tower to use ,and added my wireless card and external antenna to it , but need setting up the new PC tower to use the wireless card and antenna. How to set up the available connections so that I can use this in my garage too.
View 1 Replies View RelatedFor some reason, I cannot connect to my new build, yet everything else in the house connects.I thought maybe too many things were connected, so I unplugged everything and it is failing to work still. I am using the built in WiFi from my MOBO, and my antenna is detecting an excellent connection, but when I connect, it was giving me issues.
View 4 Replies View RelatedI need to update from older Cisco 350 Aironet 802.11a/b Wireless CardBus Adapters to Cisco cb21ag Aironet 802.11a/b/g Wireless CardBus Adapters in rugged tablet pc's. I need these without the antenna cap present to utilize the tablets antenna sytem. They are pictured on the Cisco website but Cisco partners I've contacted have been unable to assist me in purchasing them.
View 1 Replies View RelatedI have a AIR-LAP1242G-A-K9. I have several question:
1. Does the antenna is a MUST for it to work.
2. If I have a 1 unit of AIR-ANT2422DG-R (antenna) , does the wireless access still work? Do I need 2 antenna
3. If I have a 1 unit of AIR-ANT2422DG-R, does 802.11 b supported.
I connected an external 12dBi omni-directional antenna for Networks 2.4 Ghz (TL-ANT2412D) with LMR-400 cable 5M but my antenna "emits" nothing, I have no signal. With the two supplied antennas with WAP200 I signal but does not cover any desired area.
View 5 Replies View RelatedWe are installing 1260 Access Point (AIR-LAP1262N-E-K9) with 2 sets of external antenna:AIR-ANT2460NP-R (2.4Ghz, Patch Wall-mount, 6dBi Directional) & AIR-ANT5160NP-R (5Ghz, Patch Wall-mount, 6dBi Directional).What would be the recommended separation of the 2 antennas if they will be mounted beside each other?
View 1 Replies View Relatedan external Antenna for a 881G? We're using AT&T.
View 4 Replies View Relateddirectional antenna for the WAP200e.
I've been googling but can't seem to find a product. I have found omni-directional but no directional antennae
I recently checked the output of one of my AP 3502AGN which are connected to a WiSM with the current 7.0.240.0 software. There I saw the following output:
show ap config 802.11b 3502AGN-1100c-1
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... INTERNAL_ANTENNA
[Code].....
I have to replace a 1230 with an 1262 AP.
All antennas have to be in the same direction on the AP and I guess when the old 1230 is working well the 1262 will be only better . Attached u see how I plan to mount the new AP versus the old one...
When we take a look at the internal antennas on the 1142 AP, we notice the 5ghz pointed all the same way, but for the 2.4ghz we can see each offset by 45/120 degrees. It was my understanding that all antennas are omnidirectionals on the 1142, why are those 2.4ghz antennas not all pointed the same way? onfiguration advantage and that each antenna is indeed omnicadirectional? Example, if I shut just one antenna off, do I lose a sector (120degree)?
View 5 Replies View Relatedi want to install a 3500e. I have a hole in my wireless network where this AP will be a perfect fit. I do have a wireless controller running code 6.x, so I think I will need to upgrade to 7 which is not a big deal.
The problem I have is the antenna selection. Since the AP has MIMO multiple-inputs multiple-inputs I’m perplexed on the type of antenna to choose. Since the environment is a warehouse the Omni directional would be preferred - should I also add the dipole antenna for close proximity to the AP. Also, I noticed in the getting started guide the 3500e has 6 external connection points 3 for 2.4 and 3 for 5 GHz. The antenna documentation says to use dual-band antennas, but this contradicts what is shown in the getting started guide. So what antennas should I get to make the 3500e work in a warehouse environment.
where can I find SKU for HGA9N antenna? Looking in CCW but I can't find it. Neither I can find EoS notice for it.
View 4 Replies View RelatedI have a DWA-547 wireless adapter in my PC and only get 1 to 2 bars....I was thinking about getting another wireless adapter or getting wireless antennas to boost the signal if it works?
View 3 Replies View RelatedFeature AIR-CAB020LL-R AIR-CAB050LL-R AIR-CAB100ULL-R AIR-CAB150ULL-R Cable Length 20 ft (6 m)50 ft (15 m)100 ft (30 m)150 ft (46 m) Transmission Loss 1.3 dB3.4 dB4.4 dB6.6 dB for Cisco 1941W router with external antennas?
View 3 Replies View RelatedI'm going to install a Cisco Aironet 1310g (ap mode) with external antenna in a warehouse (contain many metal surfaces), and I need to install this antennas on ceiling (distance from floor to ceiling is about 13 metres). I need to get at least 1Mbps performance. AP clients are Motorola MC9190-G mobile computers.
View 3 Replies View Related mounting for the above antenna types. see figures below.
The figures above, are the antenna mounting correct? For figure 1, can the two antennas be separated by 4" or more? For figure 2, the two antennas will be side by side.
We have 3 3602Es connected to a 2504 WLC. I was wondering for best practices for antenna placement. They are all mounted on the side of a wall, near the ceiling (above everyone's head).
View 10 Replies View RelatedWhen using dipole antennas such as AIR-ANT 4941 with the 2.4 Ghz 1250 AP, must the antennas be spaced EXACTLY as far apart as the antenna connectors on the AP, or can the dipoles be spread further out, say to 4" spacing.
View 20 Replies View Related1. Does the Aironet 1242G have an internal antenna?
2. When connecting an AIR-ANT1728 omnidirectional to the primary connector on the ap, does this have to be enable or is it enable by default?
3. My laptops can connect and travel between access point just fine, but smartphones cannot even see the network.
I need to upgrade a 1230 to the new Aironet 1250 at a location. I have only 2 external antennas at that location.
I understand that you still can run 802.11n with 2 antennas. But I can not find anywhere in WLC 5508 v7.2 that I can disable the middle nut (C)
Currently have access points located throughout our warehouse that use the AIR ANT5160V-R antenna's from Cisco. These AP's are 25' in the air. However we have a lot of voice quality issues off of the 5Ghz band, we do no other services on this band as we keep data on the 2.4Ghz.This was all installed by a vendor but from what I am seeing on the documentation [URL] the cover is extremely poor for these antennas despite AP's everywhere. They cover side to side but aren't a well rounded AP at all.it seems like the AIR-ANT5145V-R would be better suited even though this is a warehouse.
View 5 Replies View Related