Feature AIR-CAB020LL-R AIR-CAB050LL-R AIR-CAB100ULL-R AIR-CAB150ULL-R Cable Length 20 ft (6 m)50 ft (15 m)100 ft (30 m)150 ft (46 m) Transmission Loss 1.3 dB3.4 dB4.4 dB6.6 dB for Cisco 1941W router with external antennas?
View 3 RepliesI have a Linksys WAG 120 N wireless router with an internal arial. I want to strengthen the signal to my laptop 2 rooms away as it keeps dropping out. Is it possible to change WAGGING from internal to external antenna to increase range/performance?
View 1 Replies View RelatedI connected an external 12dBi omni-directional antenna for Networks 2.4 Ghz (TL-ANT2412D) with LMR-400 cable 5M but my antenna "emits" nothing, I have no signal. With the two supplied antennas with WAP200 I signal but does not cover any desired area.
View 5 Replies View Relatedan external Antenna for a 881G? We're using AT&T.
View 4 Replies View RelatedI'm looking for a router with an external antenna connection so I can attach an outside antenna to extend my wi-fi signal signal around my farm.Right now I have Hughes net internet service running to a Belkin 750 router, which is descent around the house, but has no connection for an external intenna.
View 3 Replies View RelatedI'm going to install a Cisco Aironet 1310g (ap mode) with external antenna in a warehouse (contain many metal surfaces), and I need to install this antennas on ceiling (distance from floor to ceiling is about 13 metres). I need to get at least 1Mbps performance. AP clients are Motorola MC9190-G mobile computers.
View 3 Replies View RelatedWhat are the new external antenna options?
View 1 Replies View RelatedI am setting and configure the Cisco AP 1240AG with 5GHz External Antenna extension. The whole product is called iWap. The problem now is that the wireless signal amplitude only can reach 3 bars instaed of ful 5 bars.
Few questions I have for this setup and configuration :
1. What is the default or original frequency of antenna of Cisco AP1240AG? Can a 5GHz antenna work with the AP 1240AG whereby it is run with 802.11a and 802.11g?
2. If 5GHz antenna can work with 802.11a or 802.11g, what is the setting or configuration needed to be done at the Cisco 1240AG? Or, no setting or configuration needed because it will automatically work by default?
Is it possible to add an external antenna to this WRT160Nv3 router? Some spots are just on the one bar signal level that comes and goes.
View 1 Replies View RelatedIs it possible to connect two WAP200E on bridge mode without external antennas if they are 200 mts. (219 yard) apart?
View 2 Replies View RelatedI have an unusual request to support an access point with a single external antenna to cover a small physical area (elevator car!!). All Cisco's currently shipping APs have dual band antennas using MIMO for throughput in "normal" deployments. Will a deployment with a single antenna work?
View 2 Replies View RelatedI am in the process of installing a new wireless network in our offices and I was wondering if I can add an extension to the cable that connects my AIR-ANT-1728 to my AIR-CAP-3502e AP to get better coverage in our offices?
View 4 Replies View RelatedTravel in an RV and many campgrounds have poor WiFi setups. Looking for some type of external antenna I can put outside of trailer. I'm using a WMP600N adapter in a desktop PC running Win 7.
View 1 Replies View RelatedIs it possible to use only 1 external antenna (AIR-ANT2524DB-R) with 1602E Access Point?
View 3 Replies View RelatedI have a few 1142N Aironets with internal antennas in place, and I am not thrilled by its coverage. I want to extend my wireless network because of a new building which led me to the following question;Is there is any difference in wireless coverage when using external dipole antenna’s (the small ones, for example the AIR-ANT2524 for a new 2600 Aironet) versus the internal (dipole) antenna’s. I am aware you have more options when using external antenna’s, such as omni, directional, outdoor etc.
For an indoor office or warehouse deployment, where temperature is not a concern, why would I buy for example the 2600E with 4 dipole antenna’s over the 2600i?I have read most Aironet datasheets and their antenna options, but can’t find a word about the advantages of external dipole antennas. I would expect external antennas would give better coverage.. is this true?
I'm planning to use these with a 2504 controller. However, I cannot find a straight answer on whether or not the External Antennas provide better coverage than the Integrated Antennas? These will be wall mounted in a combo office/warehouse environment. Also, I cannot figure out if the External Antennas are even included with the 1602E (AIR-CAP1602E-A-K9)? or what if any power adapter/ injector is included with the AP's?
View 14 Replies View RelatedHow to add an external antenna? I'd like to mount a DCS-930L in a location (inside a metal housing) that would need the antenna to be a few inches away. Any internal layout information?
View 3 Replies View RelatedI just realized that my internet is slow when my antenna is on top of my computer. I have a pci card with an external antenna connecting to it. If it's on top of my computer, my internet is slow, but if I move it three feet in front of it, it's fast. This makes me think that my computer is somehow blocking or conflicting with the signal. Is this normal, or is there something I can fix in my computer? Download speeds with the antenna on top are around 0.54Mbps, and if I put it as far away as I can, I get around 20Mbps.
View 4 Replies View RelatedI got a different tower to use ,and added my wireless card and external antenna to it , but need setting up the new PC tower to use the wireless card and antenna. How to set up the available connections so that I can use this in my garage too.
View 1 Replies View Relatedproviding an extension for the below antennas cable length for project related requirements with the AP 1262.
AIR-ANT2506 2.4 GHz, 5.2 dBi Mast Mount Omni Ant w/RP-TNC Connector
AIR-ANT5160V-R 5GHz 6dBi Omni Antenna w/RP-TNC connector
We have the Cisco WRT54G wifi router in many offices in this building. This router has two antennas. These antenna are screw into the back of the router unit. The antenna is male and router side is female of the connector. what are these connectors (some type of RF connectors)? How can we get extension cables for these to move the antenna from one fix location to another point?
View 4 Replies View RelatedLet's say, an antenna like that Should I open the modem and therein there could be a slot for it to be plugged in? Because on the back side of the modem none of the slots will suit such plug.
View 2 Replies View RelatedI have no clue what kind of brand is the outdoor antenna. It plugs into a wap54g and I need an extension cable to my antenna, only like 6 feet, where can i buy this?
View 1 Replies View RelatedAnybody know of a extension cable for this product? D-Link 14dBi Outdoor Direct Antenna (ANT24-1400) I need at least 10-15 feet of extra length.
View 1 Replies View RelatedI have WAG320N. I attached External HDD to Router's USB.I don't know how to access to HDD and other users also..(not via internet)
View 1 Replies View RelatedThere is a USB port on my DPC3827 gateway device, and I'm trying to figure out if/how I can share an external portable hard drive I've connected to it. It's formatted FAT32. There are no places in the admin pages to configure storage sharing options.
View 1 Replies View RelatedI have web server setting behind the Linksys ADSL modem, I set the DMZ IP to my web server IP so the external internet users can access my web pages.
This setup was working fine until I switched to “Linksys X3000” modem, external internet user can no more access my web pages.I had set the DMZ IP correctly in the new modem. The local LAN users can access the pages without any problem.
Setting up a new 1941w router. Already have another one offsite that's working great. Based the new configuration on the one I have working and can route traffic, etc. My problem with this new one is that I cannot get into the embedded AP to configure. My configuration follows this question. I have checked status of the interfaces and everything is up except VLAN2. I've used the command no shutdown within the VLAN2 interface, but the operational status is still reading down. The admin status is reading up. All other interfaces are up and up. [code]
View 3 Replies View Relatedtrying to configure a 1941W router... Spent many hours on these forums... The only thing I'm still stuck on is that, I'm not able to get an IP through DHCP on the BVI1 interface of the embedded AP.
Here is my router config:
Current configuration : 3490 bytes
!
! Last configuration change at 22:00:35 PCTime Tue Aug 21 2012 by root
[Code]......
I loaded the following MIB into PRTG 'CISCO-WAN-3G-MIB' hoping to record RSSI and ECIO values on my 3G 1941W cisco router. RSSI is now recording using 'c3g current gsm rssi' however ecio isn't recording using 'c3g current gsm ec io' or 'c3g notif ec io'.[URL]
View 1 Replies View Relatedcan assist with a Cisco 1941w configuration problem.I have just installed a 1941W onto our network. It handles the routing of our block of IPs onto the internet through our ISP using 2 x ADSL2+ interfaces. his all works. For the sake of privacy, lets say that our block is 100.101.102.128/25.I am now trying to get the 1941Ws Wireless AP working.I have set up the management VLAN on a private range (192.168.1.0/24), the AP on 192.168.1.2 and can now access the AP interface on 192,168.1.2 from anywhere on our LAN.This tells me that the cisco is routing everything to and from the AP on the management network (192.168.1.0/24).
I have set up VLAN 2 on the AP, configured it to use WPA, set the key, created an SSID and assigned it to VLAN 2. I am having some trouble assigning both 2.4 and 5GHz radios to the SSD. For some reason after setting up everything using the express setup I could not save Beacon Mode unless I disabled Radio1-802.11N5GHz and now I cannot re-enable because the web interface claims that this interface is not enabled for the VLAN... but that's another question.When I try to access the AP, I am authenticated but never get an IP address. My best guess is that DHCP on the router is not responding perhaps because VLAN 2 is not routing to the main network.
The VLan2 interface on the router side is definitely enabled and set to 192.168.2.1. I have set up a DHCP pool on 192.168.2.1 that is assigned to Vlan2 (I did manually because CCP claimed there was an overlapping region.. even though there wasn't). I can ping 192.168.2.1 (or any other internal address) from the AP. VLAN 1 and VLAN 2 are set up the same way (no ACLs, both in in-zone, both with NAT off)So... why isn't the router giving the wireless client an IP address? Is there a way to simplify the AP so that VLAN 2 routes directly onto my main IP range?
As an aside... between CCP not wanting to add a DHCP range (claiming an overlapping region but manual entry worked), the AP web interface's complete lack of responsiveness (it's horribly slow) and the AP interfaces inability to provide a useful error message... this has been THE most frustrating thing I have ever had to configure.. With the rest of he industry making everything easier to use, Cisco seems to be moving in exactly the opposite direction.
Our boss decides to purchase 1941w Router & he asked me to do the necessary configuration. my knowledge in CISCO router is a CCNA level & i've never configured an embedded AP or ADSL line on a router before.
the topology is as the following: as for the wired Network, we have one LAN (192.168.1.0/24) connected to GE0/0 (192.168.1.254/24) on router & has the ability to access the internet which is ADSL configured as ATM0/0/0
As for the wireless network ( now here is the problem) what i want is the following:
I want the wireless network to share the same network with the wired which means 192.168.1.0/24 i want to use WPA encryption how to configure the AP?!
this is a true challenge for me. After a lot of searching, most of the sample configuration over there is about creating two VLANS!!! & two DHCP Pool.
Can the embedded AP be configured as a standalone AP without configuring the router's functions? I need to configure one temporarily until we get the 1252AP for the location.
View 1 Replies View Related