Cisco Wireless :: Embedded AP In 1941W Router?
Oct 24, 2011Can the embedded AP be configured as a standalone AP without configuring the router's functions? I need to configure one temporarily until we get the 1252AP for the location.
View 1 Replies
ADVERTISEMENT
Cisco Wireless :: 1941w Can't Access Embedded AP
Jun 5, 2013Setting up a new 1941w router. Already have another one offsite that's working great. Based the new configuration on the one I have working and can route traffic, etc. My problem with this new one is that I cannot get into the embedded AP to configure. My configuration follows this question. I have checked status of the interfaces and everything is up except VLAN2. I've used the command no shutdown within the VLAN2 interface, but the operational status is still reading down. The admin status is reading up. All other interfaces are up and up. [code]
View 3 Replies View RelatedCisco Wireless :: Setting Up Embedded Access Point In 1941w ISR
Jun 20, 2010I've done quite a bit of work with Cisco kit before (it isn't my speciality, however) and am currently working on setting up the embedded Access Point in a Cisco 1941w ISR.
The primary router is working fine, but I'm getting no where with the embedded Access Point. The whole IOS within an IOS just doesn't compute for me.
Our requirements are really simple.
We have a 10.0.0.0/24 internal network. We want users to be able to access this via the 1941w Wireless Access Point, in the same way that wired users access this via the Ethernet port.
The manual re. setting up the AP gives an example where IP addresses are applied to the AP, which doesn't make sense to me, as we simple want the AP to sit on the same VLAN as the ethernet port.
How the AP is supposed to interface with the primary router? Also, we want to use a WPA secret key to authenticate to AP. Is this possible? The Cisco docs seem to suggest that WPA is only possible through some 3rd party server.
Cisco Wireless :: Configure 1941w Router AP
Mar 2, 2012Our boss decides to purchase 1941w Router & he asked me to do the necessary configuration. my knowledge in CISCO router is a CCNA level & i've never configured an embedded AP or ADSL line on a router before.
the topology is as the following: as for the wired Network, we have one LAN (192.168.1.0/24) connected to GE0/0 (192.168.1.254/24) on router & has the ability to access the internet which is ADSL configured as ATM0/0/0
As for the wireless network ( now here is the problem) what i want is the following:
I want the wireless network to share the same network with the wired which means 192.168.1.0/24 i want to use WPA encryption how to configure the AP?!
this is a true challenge for me. After a lot of searching, most of the sample configuration over there is about creating two VLANS!!! & two DHCP Pool.
Cisco Wireless :: 1941w - Cannot Ping Bvi1 From Router
Aug 28, 2012I have vlan 1 in 192.168.5.1 255.255.255.0 and bvi1 192.168.5.2 255.255.255.0. It was working before but something happened and I cannot figureout what. Vlan1 cannot ping bvi and viceversa.
View 2 Replies View RelatedCisco Switching/Routing :: 891-W Router With Embedded AP?
Dec 26, 2012I do not understand where in the CCP I can configure PAT for communication back 7960G VoIP phone with SIP firmware Maybe I'm wrong on the concept of communication pass back to the Voice VLAN.
View 1 Replies View RelatedCisco Switching/Routing :: Add E1/T1 WIC To 5915 Embedded Service Router?
May 15, 2012Is there any way to add an E1/T1 WIC to the 5915 Embedded Service Router?
Can I add any additional cards to it?
Cisco Wireless :: 892W / Closing Session On Embedded AP?
Mar 27, 2013I'm working on a 892W router.To close the session between the wireless device and the router's console, the command Control-Shift-6 x is required.The Issue is that this command is not working for me. I'm using a SuperPuTTY connecting tool.
View 7 Replies View RelatedWireless :: Sylvania 7 Netbook With Windows Embedded 7?
Feb 11, 2012I done had dis sylvania 7" for 7 months and i keep gonna on google to try and fix it. i took it to a computer store and it took dem a month to fix it and when i got home i still could not get on da net i have tried everything on Google and dat dont work i got clear and hot spots. I am ready 2 throw dis thing in da trash and i didnt get 2 play wit it yet?
View 3 Replies View RelatedCisco Router 1941W - WAN Keeps Disconnecting Randomly?
Oct 23, 2012We are using Cisco router (1941W model) and our the WAN interface keeps going down randomly (sometimes happened twice within 1 hour, sometimes worked fine for 2-3 days before getting disconnected). After getting disconnected, if we unplug the cable that connects our router to the fiber terminal and then plug in back, everything works fine immediately.
We had asked our Internet Provider to come 3 times to check the network line, renew the fiber terminal and do some investigations, they said there should be no issue on their side. If it's true then there must be something wrong with the router.
We also enabled ip accounting on the router and saw very low rate of small packets coming to WAN interface.
During the downtime, LAN interface still worked fine.
Cisco VPN :: Need IPSEC VPN Capability On 1941W Router
Oct 27, 2011I recently purchased a 1941W Router and upgraded it to IOS15.2T. After upgrading I was disapointed to see that it didn't have IPSEC VPN capability. What do I have to do to get this support activated/installed on this device?
View 1 Replies View RelatedCisco WAN :: Devices Connected To 1941w Router Cannot Ping
Sep 18, 2011I have a copper over ethernet connected to an adtran 908e connected to an ASA 5505 with a port 192.168.150.254 connected to the router on the Gigabitethernet 0/0
I can ping to internal and external ip addresses but when a device is connected through the wireless signal then the device cannot ping anything; what could be stopping the device from pinging any ip addresses internal and external?
I posted my current config for the router and ap:
Router:
Current configuration : 2245 bytes
!
! Last configuration change at 16:03:06 UTC Tue Sep 6 2011
[Code].....
Cisco Wireless :: Recovering Embedded Access Point 881w Password
Mar 19, 2012I simply need to recover an embeded access point password.
I have the passwords to the 881-w router, but passwords to the embedded access point I don't have.
What is the recovery process for it, or the password reset process for the embedded access point.
Cisco WAN :: 1941w AP Can't Ping 2nd Router / Host But Interface Reachable
Feb 2, 2013From the router I can ping the 2nd router, all its host and all of the 1941w interfaces.
From the 1941w AP i cannot reach the 2nd router or any of its host, but I can reach the interface that is connected to the 2nd router but only one side of it.
Attached are both my router and ap configs. At the moment I am just trying to reach the 2nd router and its host so I can update the AP IOS image but cannot reach the tftp server.
Cisco Wireless :: 1941W Can't Get IP Via DHCP On BVI1
Aug 20, 2012trying to configure a 1941W router... Spent many hours on these forums... The only thing I'm still stuck on is that, I'm not able to get an IP through DHCP on the BVI1 interface of the embedded AP.
Here is my router config:
Current configuration : 3490 bytes
!
! Last configuration change at 22:00:35 PCTime Tue Aug 21 2012 by root
[Code]......
Cisco Wireless :: Record 1941W EC IO Using PRTG?
Apr 27, 2013I loaded the following MIB into PRTG 'CISCO-WAN-3G-MIB' hoping to record RSSI and ECIO values on my 3G 1941W cisco router. RSSI is now recording using 'c3g current gsm rssi' however ecio isn't recording using 'c3g current gsm ec io' or 'c3g notif ec io'.[URL]
View 1 Replies View RelatedCisco Wireless :: 1941w Configuration On NAT Network?
Feb 20, 2013can assist with a Cisco 1941w configuration problem.I have just installed a 1941W onto our network. It handles the routing of our block of IPs onto the internet through our ISP using 2 x ADSL2+ interfaces. his all works. For the sake of privacy, lets say that our block is 100.101.102.128/25.I am now trying to get the 1941Ws Wireless AP working.I have set up the management VLAN on a private range (192.168.1.0/24), the AP on 192.168.1.2 and can now access the AP interface on 192,168.1.2 from anywhere on our LAN.This tells me that the cisco is routing everything to and from the AP on the management network (192.168.1.0/24).
I have set up VLAN 2 on the AP, configured it to use WPA, set the key, created an SSID and assigned it to VLAN 2. I am having some trouble assigning both 2.4 and 5GHz radios to the SSD. For some reason after setting up everything using the express setup I could not save Beacon Mode unless I disabled Radio1-802.11N5GHz and now I cannot re-enable because the web interface claims that this interface is not enabled for the VLAN... but that's another question.When I try to access the AP, I am authenticated but never get an IP address. My best guess is that DHCP on the router is not responding perhaps because VLAN 2 is not routing to the main network.
The VLan2 interface on the router side is definitely enabled and set to 192.168.2.1. I have set up a DHCP pool on 192.168.2.1 that is assigned to Vlan2 (I did manually because CCP claimed there was an overlapping region.. even though there wasn't). I can ping 192.168.2.1 (or any other internal address) from the AP. VLAN 1 and VLAN 2 are set up the same way (no ACLs, both in in-zone, both with NAT off)So... why isn't the router giving the wireless client an IP address? Is there a way to simplify the AP so that VLAN 2 routes directly onto my main IP range?
As an aside... between CCP not wanting to add a DHCP range (claiming an overlapping region but manual entry worked), the AP web interface's complete lack of responsiveness (it's horribly slow) and the AP interfaces inability to provide a useful error message... this has been THE most frustrating thing I have ever had to configure.. With the rest of he industry making everything easier to use, Cisco seems to be moving in exactly the opposite direction.
Cisco WAN :: Does 1941 (not 1941W) Have Wireless Controller
Aug 25, 2011I currently have:
- 1941 (not wireless) router
- 1140 Access Point
It looks like I got the controller-based AP instead of the standalone. My question is, does the 1941 (not 1941W) have a wireless controller? If not, is there a controller module that I can add to my router? Or should I return the AP I have for the standalone version (or the 1941 for the 1941W)?
Cisco Wireless :: 1941W With External Antenna Cable?
Jan 14, 2013Feature AIR-CAB020LL-R AIR-CAB050LL-R AIR-CAB100ULL-R AIR-CAB150ULL-R Cable Length 20 ft (6 m)50 ft (15 m)100 ft (30 m)150 ft (46 m) Transmission Loss 1.3 dB3.4 dB4.4 dB6.6 dB for Cisco 1941W router with external antennas?
View 3 Replies View RelatedCisco Wireless :: 1941W Basic Configuration Required
Apr 22, 2012I am replacing a cisco linksys router with a 1941w.
I have the 0/0 accepting a DHCP from the ISP then I have 0/1 going to a switch and hosting a dhcp server.
Where I have an issue is:
A) Finding a way to turn on the wireless and make it use the same DHCP as wired and setting up a user name/wep password
B) Turning on the GUI that is supposed to be embedded on this.
C) Finding a way to make the DNS point to the default gateway so that I don't have to set the address everytime we move the box.
Here is my current configuration, and with it I can get onto the wired network and get to the internet.
Current configuration : 4712 bytes
!
! No configuration change since last restart
version 15.1
[Code]...
Cisco Switching/Routing :: Open Specific Ports On 1941w Integrated Services Router
Apr 20, 2013open specific ports on 1941w Integrated Services Router.This specific router is a wireless VPN router that has a wired module and a wireless module and VPN so I'm getting 3 subnets on my network - 192.168.1.. for the wired connections, 10.100.1.... for wireless LAN connections and 10.100.2... for VPN remote connections.I know that by default all connected computers can access my Linux server data through telnet so the telnet port is open by default, the problem is that I have some other software licensing system on my Linux box that needs to be accessed through port 27000 and most of my users are using wireless connections and can't access that license because post 27000 is closed.what is the comand to open this post or any other port that I need to be open on the wired module, wireless module and VPN or at least poit me to somewhere where I can find all the commands that I can use for this router?
View 6 Replies View RelatedCisco WAN :: Embedded Packet Capture On ASR1000
Oct 30, 2012I'm trying to use EPC on ASR1001 running IOS-XE 3.4, and it won't work. Configuration commands are accepted by the router, but there are no packets in the capture buffer.In release notes for IOS-XE, in the 2.5 section, there is a statement that EPC is not supported on ASR1k. Is it true also for newer versions of IOS-XR?
View 1 Replies View RelatedCisco WAN :: Embedded Packet Capture On ASR 1001
Feb 5, 2012I have a need to capture traffic on an ASR 1001 subinterface, but what I have found is that the Embedded Packet Capture feature is not supported on this platform. Are there any simple alternatives to capture egress traffic on a subinterface or am I SOL? This is a walk in the park on normal IOS routers...
View 1 Replies View RelatedCisco VPN :: 5500 AnyConnect Essentials / Embedded CA
May 11, 2011I have a Cisco ASA 5500 Series appliance.I'd like to use the Embedded CA There’s no documentation which states an AnyConnect Essentials license will suffice, over an AnyConnect Premium.url... hints at Essentials being enough, as it specifically mentions some features require Premium, but I really need to be sure. Using AnyConnect Essentials (so, anyconnect essentials: Enabled) AND the Embedded CA?
View 1 Replies View RelatedCisco WAN :: Configuring Cellular 0 On 881G With Embedded 3G Modem
Jun 5, 2012 I have a Cisco 881G with PCEX-HSPA-3G card for which I have successfully configured for internet. As the above one has come to end of life, we got the replacement 881G with embedded 3G modem.
I can't get Cellular 0 to use ppp encapsulation:
Router(config-if)#encapsulation ppp
Cellular0: Only SLIP encapsulation supported
Router(config-if)#
[Code].....
Cisco :: NM-16A / Embedded Menu Manager For Terminal Server?
Mar 25, 2012Using EMM as a nice friendly interface for their terminal server (ie router with NM-16A and octal cables)?when I ask the framework to run the following command it gets stuck will a blinking cursor and clear screen
<IOSExecCommand>"connect 10.1.1.1 2000"</IOSExecCommand>
however removing the port number allows it to connect fine.
<IOSExecCommand>"connect 10.1.1.1"</IOSExecCommand>
same symptom if iI were to replace connect with telnet
<IOSExecCommand>"telnet 10.1.1.1 2000"</IOSExecCommand>
even setting up an iphost does the same ie:
ip host R1 2000 10.1.1.1
<IOSExecCommand>"connect R1"</IOSExecCommand>
All of these commands work fine from the # prompt
Cisco WAN :: Cannot Enable Embedded-Service-Engine On 2911
Dec 1, 2012i cann't enable embedded-Service-Engine on cisco2911 router.
View 3 Replies View RelatedCisco Switching/Routing :: Configuring Ssh Access To 887vaW Embedded AP?
May 17, 2012i got some problem configuring my cisco 887VAW internet access point.I want to be able to manage it thru ssh console with the service-module wlan-ap0 session mode. And i want to access thru http but it's not working too I show you my config
This is my config :
Current configuration : 3281 bytes
!
! Last configuration change at 21:43:11 UTC Fri May 18 2012 by jon
! NVRAM config last updated at 21:46:05 UTC Fri May 18 2012 by jon
! NVRAM config last updated at 21:46:05 UTC Fri May 18 2012 by jon
version 15.1
[code]....
Cisco WAN :: Interface Embedded-Service-Engine In 1900 Series
May 3, 2011Sure this is a simple one. New to the 1900 series routers, have a 1921 with IOS 15.1. Noticed that there is a standard interface labeled Embedded-Service-Engine0/0. What the purpose of this is? Cannot seem to find any detail on it. See extract from default config below.
View 5 Replies View RelatedCisco Switching/Routing :: Embedded Event Manager On 3560 Switch
Jul 12, 2012I have EEM configured on cisco 3560 switch. The configuration is below. I want that switch inform me through email when device with particilular IP address become unavailable. I already try to debug this with debug event manager action mail but didn't see any output. [code]
View 2 Replies View RelatedCisco Switching/Routing :: Cannot Remove Embedded Service Engine Interface In 2951
Mar 5, 2012I have removed an embbedded service engine modole from an 2951 router, after reboot the rouiter. the service engine interface still appears; any command can I use to completely remove it.
View 2 Replies View RelatedCisco :: 1941W Built-in AP Goes Down?
Dec 26, 2012how to debug why sometimes the dot11radio0 / 1 go down? Sometimes, the lights on the router indicating the radio status go out. Usually, a reload of the ap will bring them back up...Maybe hardware is starting to fail? Just unsure on how to debug to find out why it turns off sometimes.
View 1 Replies View RelatedCisco WAN :: Unable To Ping Across Subinterface On 1941w
Oct 10, 2011I am currently working on a 1941w router. The problem that I am having is that I am unable to ping the switch that is directly connected to it and I am unable to ping from the switch to the router. If I take the address off of vlan 1 and move it to gi0/0.1 the pings work, but then client traffic on the wireless ap inside the 1941w fails.
Here is the releveant config off of the 1941w
version 15.0
no service pad
service timestamps debug datetime msec localtime show-timezone
[Code].....
