Cisco Switching/Routing :: Add E1/T1 WIC To 5915 Embedded Service Router?
May 15, 2012Is there any way to add an E1/T1 WIC to the 5915 Embedded Service Router?
Can I add any additional cards to it?
ADVERTISEMENT
Cisco Switching/Routing :: Cannot Remove Embedded Service Engine Interface In 2951
Mar 5, 2012I have removed an embbedded service engine modole from an 2951 router, after reboot the rouiter. the service engine interface still appears; any command can I use to completely remove it.
View 2 Replies View RelatedCisco Switching/Routing :: 5915 - Combining FE0/1 And FE0/2-4 In Same Address Space
Mar 20, 2013I have a 5915 mobile router with software version 15.2(1r)GC1. Ports FE0/0 and FE0/1 are routed ports. Ports FE0/2 through FE0/4 are layer 2 switched ports. I'd like to put FE0/1 and FE0/2-4 in the same address space so that all four ports can be used as a single LAN and FE0/0 would be used as a WAN port. How do I configure the router to place FE0/1 and FE0/2-4 in the same LAN.
View 1 Replies View RelatedCisco Switching/Routing :: 891-W Router With Embedded AP?
Dec 26, 2012I do not understand where in the CCP I can configure PAT for communication back 7960G VoIP phone with SIP firmware Maybe I'm wrong on the concept of communication pass back to the Voice VLAN.
View 1 Replies View RelatedCisco WAN :: Cannot Enable Embedded-Service-Engine On 2911
Dec 1, 2012i cann't enable embedded-Service-Engine on cisco2911 router.
View 3 Replies View RelatedCisco WAN :: Interface Embedded-Service-Engine In 1900 Series
May 3, 2011Sure this is a simple one. New to the 1900 series routers, have a 1921 with IOS 15.1. Noticed that there is a standard interface labeled Embedded-Service-Engine0/0. What the purpose of this is? Cannot seem to find any detail on it. See extract from default config below.
View 5 Replies View RelatedCisco Switching/Routing :: Configuring Ssh Access To 887vaW Embedded AP?
May 17, 2012i got some problem configuring my cisco 887VAW internet access point.I want to be able to manage it thru ssh console with the service-module wlan-ap0 session mode. And i want to access thru http but it's not working too I show you my config
This is my config :
Current configuration : 3281 bytes
!
! Last configuration change at 21:43:11 UTC Fri May 18 2012 by jon
! NVRAM config last updated at 21:46:05 UTC Fri May 18 2012 by jon
! NVRAM config last updated at 21:46:05 UTC Fri May 18 2012 by jon
version 15.1
[code]....
Cisco Switching/Routing :: Embedded Event Manager On 3560 Switch
Jul 12, 2012I have EEM configured on cisco 3560 switch. The configuration is below. I want that switch inform me through email when device with particilular IP address become unavailable. I already try to debug this with debug event manager action mail but didn't see any output. [code]
View 2 Replies View RelatedCisco WAN :: 5915 Router To Configure Multicast To Pass
Apr 9, 2013I have a 5915 router. Trying to configure multicast to pass. I have implemented different version of the configuration, but the attached is the latest and suggest by CCIE support. I have a Java program on one side of the router that pulls the multicast traffic fromt he other side of the router. The data is not getting to the java program with this configuration. I have been working on this for a week and unable to see anything. Wireshark doesn't see the traffic. In the attached config, I have also included some stats.
hostname HPIB-Rtr!boot-start-markerboot system flash:C5915-ADVENTERPRISEK9-MZ.SPA.152-1.GC.BINboot-end-marker!!!no aaa new-modelcrypto pki token default removal timeout 0!!!!!
!ip multicast-routing ip cefno ipv6 cef!multilink bundle-name authenticated
interface Loopback0ip address 10.10.1.3 255.255.255.255ip pim sparse-mode!interface Loopback100ip address 192.168.3.1 255.255.255.0ip pim sparse-modeip igmp static-group 239.255.10.10!interface FastEthernet0/0ip address 172.30.255.1 255.240.0.0ip pim sparse-modeip nat outsideip virtual-
[Code].....
Cisco Switching/Routing :: Cat6500 SUP-2T Service Module
Apr 12, 2012Using the new SUP-2T, need to clarify one query. If we are using the new SUP-2T in VSS mode, will the new ASA service module and NAM-3 are supported? From Cisco site, ASA module FAQ:
Q. Will the ASA Services Module support the Cisco Catalyst Virtual Switching System (VSS) at FCS?
A. Yes, depending on which supervisor you use. The ASA Services Module supports VSS either as a single firewall or as a failover pair of firewalls, when used with the Supervisor 720-10G (VS-S720-10G-3C and VS-S720-10G-3CXL). Transparent and multi- context modes also work with the VSS in this configuration. However, though the SUP 720-3B (WS-SUP720-3B and WS-SUP720-3BXL) is supported by the ASA Services Module, it is not capable of supporting the VSS. No reference to Supervisor-2T.
Cisco Switching/Routing :: 6500 - VSS And ASA Service Module
Mar 10, 2013we are planning to implement a VSS solution with a 6500 series switches with sup 2T. We also need to include an ASA service module on the design, however the budget is not enough to buy two asa service modules. So i want to know if is possible run a VSS cluster, whit only one ASA service Module. and also i would like know what happens if the single ASA service module fails? can the switch cluster continue operating just as if there is not a firewall installed?
View 1 Replies View RelatedCisco Switching/Routing :: 2911 Can Support Ip Service Image
Feb 29, 2012i want to check if cisco2911-sec/k9 can support IP service image? what PAK(license) can be bought to activate the IP service feature set?
View 1 Replies View RelatedCisco Switching/Routing :: N7K No Drop In Service To Existing VLAN
Aug 8, 2012When you use the command switchport trunk allowed vlan add [vlan-id]There should be no drop in service to the existing VLANs, correct? I am trunking from a 7K to a 2960S via 2G PoCh.
View 2 Replies View RelatedCisco Switching/Routing :: 3640 Can't Apply Service-policy?
Mar 21, 2013I got this 3640, trying to apply a service-policy (output and input), but seems like I do it something wrong...because he only apply the output policy... here the config, I already try to config the service police inside the fa0/0, but is not showed at all, he only show the output, its like I never apply that
View 1 Replies View RelatedCisco Switching/Routing :: IP Base To IP Service License Of 3750x
Dec 8, 2012I am having a ws-3750x-12s-s switch . I want to upgrade it from ipbase to ip service. after installing ip service liciense file, when i gave command " show license detail" i found there 3 index . one is for ip base -active (permanent) ..2nd is for ip service-active(permanent) 3rd is again ip service but inactive( period 8weeks 2days) , then i cleared 1st one by giving command "clear ipbase" and reboot. but still 2 index .both for ipservice one is permanent-active another is inactive . so my question is how can i remove 2nd index which one is inactive and time period for 8weeks and 2days..?? becasue i don't need it. and it will make any problem in future ?
View 2 Replies View RelatedCisco Switching/Routing :: 1941W - Service Module Failed
Jul 25, 2012we have approx. 70 Cisco 1941W routers deployed in our company. I used to be able to console into the internet wireless AP by issuing the below command:
service-module wlan-ap0 session
However lately this hasn't been working and AP just simply refuses connection. Here is what I have for Status. I have tried reseting the Service Module to no avail.
Router#service-module wlan-ap0 status
Service Module is Cisco wlan-ap0
Service Module supports session via TTY line 67
Service Module is failed
Service Module reset on error is disabled
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
Cisco Wireless :: Embedded AP In 1941W Router?
Oct 24, 2011Can the embedded AP be configured as a standalone AP without configuring the router's functions? I need to configure one temporarily until we get the 1252AP for the location.
View 1 Replies View RelatedCisco Switching/Routing :: Cat 2960 - Map / Service-Policy Input Is Not Working
Nov 10, 2011I have some trouble with that policy-map on my 2960 or 3560 switches with LAN base 12.2(53)SE2. I want to use that feature to catch video traffic from webcams in laptops which can't send dscp values out of the box. This is my test config to check if the function is working: catch every traffic from my workstation for testing, access-list 101 permit ip any any, class-map match-all CL_TEST
1. I can't see any counters with the command "sh policy-map interface FastEthernet 0/1". Cisco tells that this command is not possible. But how I can see if the policy is working correct?
2. When I did the configuration I can't see any packets with dscp af41 on the out going interface on the switch with "sh mls qos int gi0/1 statistic" as I expected. After reloading the switch I see the pakets with af41. Okay for that moment. But.After that I changed something in the policy-map. Only "set ip dscp ef" for a second test.
Generating some traffic I see only packets with af41 as before I changed the policy-map. No traffic with ef on the outgoing interface.
Cisco Switching/Routing :: How To Configure Sm-es2-16-p Service Module To Route Over 2911
Jun 17, 2012Any example of how to configure an sm-es2-16-p service module to route over an Cisco 2911?
View 2 Replies View RelatedCisco Switching/Routing :: 6509 VSS Implementation As A Service Module Core
Jun 8, 2011I m planning to implement VSS in core but want some inputs on IOS as i have FWSM as a service module Core :- Ii am running 12.2(33)SXH2a on my Core 6509 and i checkd cisco sites and Fwsm release notes but it states only I-Train of IOS while mine is H-Train so can I directly upgrade to I-Train or I was thinking of SXH8b IOS.
View 2 Replies View RelatedCisco Switching/Routing :: SM-ES2-24 - Installation Of Enhanced EtherSwitch Service Module
Dec 12, 2011I have a 2911 ISR and want to install a SM-ES2-24 Enhanced EtherSwitch Service Module.
Do I need to power down the router?
Cisco Switching/Routing :: 2600 DHCP From Service Provider Not Working
Feb 7, 2013So I have a 2600 that I have configured three sub interfaces on. FA0.0.1 is set for DHCP and supports VLAN 1. FA 0/0.2 for Voice, FA 0/0.3 for Data. I have this router interface plugged into FA 0/24 on my 3550 and the 3550 is configured as a dot1Q trunk (I have attached configs for RTR and SW).I have most ports configured as access VLAN 1 which is where i have my ISP connection plugged FA0/1 on the 3550. When I connect the service provider link FA0/0.1 never picks up an address. If I take my internal DHCP server and connect it to FA0/1 of the 3550 it snags an address almost immediately.In my mind this validates that my config is fine. I also took the same cable from the service provider cable modem and connected it to my laptop and the laptop is pulling DHCP.
View 4 Replies View RelatedCisco Switching/Routing :: Enable Dhcp Service On 3560 Switch
Mar 19, 2012can you enable dhcp service on a 3560 switch.
View 3 Replies View RelatedCisco Switching/Routing :: 2921 / How To Quit Service-module Session
Jun 9, 2012On 2921, how do you quite service-module session and get back to the router?
View 3 Replies View RelatedCisco Switching/Routing :: WS6724-SFP / Flapping Interfaces With Service Policy
Jun 2, 2013i just configured a C6K VSS with Sup2T, 15.1SY IOS software and a WS6724-SFP module with the follwing cos config:
auto qos default
table-map cos-discard-class-map
map from 0 to 0
map from 1 to 8
map from 2 to 16
[code]....
After applying the service policy to one interfac of the WS6724-SFP module the policy is deployed to all interfaces of the module. So far it should be ok but after a short time all interface of the module begin to go down an up and down and up ... flapping.
Cisco Switching/Routing :: 3750 - Use MLS QoS Trust DSCP With Service-policy?
Dec 24, 2012i would like to know the possibility to use mls qos trust dscp with service-policy in the IOS ver.12.2(25)SEE2.The specific version is not possible to configure like below.
Cat3750(config-if)#do sh run int f1/0/1
Building configuration...
[code]....
Cisco Switching/Routing :: 3750 Service Policy Output Not Supported
Jan 26, 2009I have a 3750 switch (c3750-ipbasek9-mz.122-46.SE.bin) were i want to add bandwitdh limit pr. interface, doing the following:
ip access-list extended customer_A
permit ip any any
class-map match-all BW_10Mbps
[Code]....
When i trie to apply the "service-policy output 10 Mbps" to the interface, it says the service-policy output is not supported on the switch. Is this a software related isue ?
Cisco Switching/Routing :: 2851 - Service Module Won't Accept IP Stating
Oct 18, 2012[code]....
I can access the ACNS with this config. The issue is that it will not cache anything when I enable WCCP on both ends. I am unable to set the gateway to the IP (even when static) to the WAN interface IP with the error Network Unreachable by content engine. If I address it within the 192.168.2.X network and gateway to 2.1, it locks up when cache is enabled. 192.168.0.5 (the external wan int) is unreachable as a gateway.
I've tried the unnumbered ip on the internal interface but then the service module won't accept an IP stating that the router side must have an IP set.
I had WCCP attempting to cache but timing out on everything without caching a thing. I want/need to understand the IP routing before I get ahead of myself.
Cisco Switching/Routing :: Service Policy Input Not Working 6509 VSS
Jan 6, 2013interface Vlan24
description Internal Wireless Internet
ip address 10.x.0.1 255.255.254.0
[Code]....
So, I am trying to limit the bandwidth used by this vlan. The service-policy output statement works, the service-policy input statement does not. My test is to get on that vlan and go to speedtest.net. My download speeds are about 3.5Mb/s, my upload speeds are about 20Mb/s.
it has something to do with this:
sh mls qos ip
QoS Summary [IPv4]: (* - shared aggregates, Mod - switch module Sid - Switch Id)
Int Sid Mod Dir Class-map DSCP Agg Trust Fl AgForward-By AgPoliced-By
[Code].....
Cisco Switching/Routing :: 5548 Method To Renumber FEX Without Causing Service Disruption
Jul 10, 2012Any method to renumber a FEX without causing service disruption?
1) Preprovisioning the new FEX number
2) Mirror the config
3) Change the FEX association on the FEX downlink ports on the 5548
but I'm certain this will cause a disruption to the connected hosts ports which are in production on the FEX?
Cisco Switching/Routing :: Block Potential Denial Of Service In 3750 Switches?
Jan 11, 2012How to block Potential Denial of Service in cisco 3750 switches.
View 1 Replies View RelatedCisco Switching/Routing :: 3560 / Administrative Control On L3 Switch For DHCP Service
Sep 25, 2012My Network Layout is as, Firewall (with Routing)------>Cisco 3560 Switch (L3)------> connected 8 Cisco 2960 switch (L2)----> all users I have configured 20 VLAN's on cisco 3560 switch with Dynamic Pool and Static, Means, 5 Vlan's are Dynamic and remaining are Static Our Company process provides only internet access to existing clients computers. Problem is that, I configured Static VLAN 5 for one of our Client in their seperate room, mean to say, i activated all ports of their room with Static VLAN 5. one day they configured own DHCP server on Windows 2003 Server with same subnet (Same as VLAN5) in their room without any information and now their all computer/ Laptop acquiring ip address Dynamically.
If i have configured Static vlan on that port's then how it is get Dynamic ip from same port's.How to restrict to permit another DHCP server/Service in our premises. I Do not want to give administrative control to Clients to do such kind of thing with LAN.
Cisco Switching/Routing :: 7600 Service Provider Has 1000-Full With Auto-negotiate
Jan 21, 2013I have a port on 7600 connecting via Single Mode Fibre to my service provider. Service provider has 1000-Full with auto-negotiate. I am seeing following output on my 7600. [code] if this interface is only capable of doing 1000Mb, how come it is showing 100-Full. If I change to nonegotiate option (both my side and provider side), link goes down. My provider has confirmed they have 1000Full their side.
View 2 Replies View Related