Cisco Switching/Routing :: Configuring Ssh Access To 887vaW Embedded AP?
May 17, 2012
i got some problem configuring my cisco 887VAW internet access point.I want to be able to manage it thru ssh console with the service-module wlan-ap0 session mode. And i want to access thru http but it's not working too I show you my config
This is my config :
Current configuration : 3281 bytes
!
! Last configuration change at 21:43:11 UTC Fri May 18 2012 by jon
! NVRAM config last updated at 21:46:05 UTC Fri May 18 2012 by jon
! NVRAM config last updated at 21:46:05 UTC Fri May 18 2012 by jon
version 15.1
[code]....
View 1 Replies
ADVERTISEMENT
Jun 5, 2012
I have a Cisco 881G with PCEX-HSPA-3G card for which I have successfully configured for internet. As the above one has come to end of life, we got the replacement 881G with embedded 3G modem.
I can't get Cellular 0 to use ppp encapsulation:
Router(config-if)#encapsulation ppp
Cellular0: Only SLIP encapsulation supported
Router(config-if)#
[Code].....
View 9 Replies
View Related
Dec 26, 2012
I do not understand where in the CCP I can configure PAT for communication back 7960G VoIP phone with SIP firmware Maybe I'm wrong on the concept of communication pass back to the Voice VLAN.
View 1 Replies
View Related
May 15, 2012
Is there any way to add an E1/T1 WIC to the 5915 Embedded Service Router?
Can I add any additional cards to it?
View 1 Replies
View Related
Jul 12, 2012
I have EEM configured on cisco 3560 switch. The configuration is below. I want that switch inform me through email when device with particilular IP address become unavailable. I already try to debug this with debug event manager action mail but didn't see any output. [code]
View 2 Replies
View Related
Mar 5, 2012
I have removed an embbedded service engine modole from an 2951 router, after reboot the rouiter. the service engine interface still appears; any command can I use to completely remove it.
View 2 Replies
View Related
Jan 26, 2013
I have a 2960 SI lan lite switch that I am configuring for admin and guest access. I have wireless AP's plugged into trunked ports 2 and 3. I am using two vlan's (in addition to the native VLAN). Vlan 5 for Admin and Vlan 10 for guest access. I have ACL configured on the router preventing guest users from accessing the Admin network. I want to prevent those on the guest network from seeing other hosts in the vlan however the lan lite software does not support port ACL's. Any way to accomplish this with this switch.
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code]...
View 5 Replies
View Related
Jun 5, 2013
Setting up a new 1941w router. Already have another one offsite that's working great. Based the new configuration on the one I have working and can route traffic, etc. My problem with this new one is that I cannot get into the embedded AP to configure. My configuration follows this question. I have checked status of the interfaces and everything is up except VLAN2. I've used the command no shutdown within the VLAN2 interface, but the operational status is still reading down. The admin status is reading up. All other interfaces are up and up. [code]
View 3 Replies
View Related
Jun 20, 2010
I've done quite a bit of work with Cisco kit before (it isn't my speciality, however) and am currently working on setting up the embedded Access Point in a Cisco 1941w ISR.
The primary router is working fine, but I'm getting no where with the embedded Access Point. The whole IOS within an IOS just doesn't compute for me.
Our requirements are really simple.
We have a 10.0.0.0/24 internal network. We want users to be able to access this via the 1941w Wireless Access Point, in the same way that wired users access this via the Ethernet port.
The manual re. setting up the AP gives an example where IP addresses are applied to the AP, which doesn't make sense to me, as we simple want the AP to sit on the same VLAN as the ethernet port.
How the AP is supposed to interface with the primary router? Also, we want to use a WPA secret key to authenticate to AP. Is this possible? The Cisco docs seem to suggest that WPA is only possible through some 3rd party server.
View 40 Replies
View Related
Mar 19, 2012
I simply need to recover an embeded access point password.
I have the passwords to the 881-w router, but passwords to the embedded access point I don't have.
What is the recovery process for it, or the password reset process for the embedded access point.
View 8 Replies
View Related
Jun 6, 2013
I have had a replacement router sent out to me due to a fault with the AP.
It had a really old firmware on the AP, which I have updated. Using CCP, I have a wireless network running which is more than I had with the old router.
The issue I have is that there is no gui, just a webpage with a few lines showing commands etc.
I know tha CLI is probably more powerful, but I prefer a GUI.
Looking at the flash of the AP, there seems to be lots of files, which I imagine are part of the gui, so its really just a case of enabling it I would assume.
View 3 Replies
View Related
Aug 5, 2012
I'm trying to configure intervlan routing between a cisco 2801 router and HP/Amer switches. Using int fa0/1 and subinterfaces I was sure I had it configured correctly, but I cannot ping the default gateways when I place a host in a particular vlan. Below is what I have configured.
HP switch - port 9 connects to fa0/1 on 2801
ip default-gateway 10.1.100.1
trunk 9 Trk1 trunk
trunk 10 Trk2 trunk - to another switch
[code].....
View 4 Replies
View Related
Oct 28, 2012
Our company uses a commercial copier monitoring package called FMAudit to obtain meter readings from our clients' copiers, and it uses a feed to send the readings back to us. We have used port 90 for this purpose.Due to a recent server crash and emergency reconfiguration of our network, we have moved our FMAudit central server from in-house to a hosted service, with of course a different external IP address.
Without interfering with our other systems, is there a way to redirect JUST PORT 90 to another IP address external to our own? I don't care if it has to happen at the router or server level. We are using Server 2003 and a Cisco 887VAW.
View 2 Replies
View Related
Jun 1, 2013
Configuring an application using routing mode on cisco ace clients ---asa--3750--cisco ace--- servers behind vip,visa card transaction servers.i am able to setup a vip on ace using routing mode on ACE,as the servers need to see the client ip ,so we are not performing SNAT,this part is working fine,when a request comes from the client ,it goes to the vip and to one of the backend servers ,and the request will be forwaded back to the ace ,as the default gateway on the servers is pointing to the server vlan on ace.but if the transaction from the servers need to go to the visa card transaction servers ,how can we achieve this ,and after fetching the data from visa servers,does the reply will be fwd to the ACE or ASAs directly.
View 1 Replies
View Related
May 25, 2012
I currently have a Cisco 891 running with a FTP running on port 21. I currently have the NAT from external IP to and internal IP 192.168.12.6 for port 21. And the firewall allowing that traffic through and client software is working fine. However I need this FTP to be running on port 990 and anytime I change the NAT and the firewall, the external FTP clients connect but then drop when recieving the directory listing.
View 10 Replies
View Related
Feb 21, 2013
I have IP phones connected to 2960 i want to segregate traffic traffic comming from IP phones which has a COS value of 5 and want to allocate a band width of 200 MBPS for those traffic .
Can any one share sample QOS configuration for achiving this in 2960 ?
View 2 Replies
View Related
Jun 10, 2013
We think we have configured the ACE and Tacacs properly as we auth, but are not able to enter into configuration mode.
ACE-4710 A4(2.3)
View 1 Replies
View Related
Aug 4, 2012
I'm configuring VSS with two Sup2T but the Sup2T of the standby not coming active
View 6 Replies
View Related
May 22, 2013
I'm looking for some input on configuring vPC on the Nexus 3048.I know that it's supported to use 1G interfaces for the vPC Peer-Link, but using 2x1G for the Peer-Link would make the Peer-Link a bottle-neck if the 10G ports are used in a vPC. What about using 2x10G ports for the Peer-Link and using the remaining 10G ports in one, or potentially two vPCs. Should that work or is it in any way not recommended? The reason I'm asking is that the 10G ports are called "Uplink" ports in the data sheets for the 3048.
We are planning to connect some servers to the 3048s using vPC with each server connected by 4x1G interface (2x1G for each switch), and then we want to connect a Netapp storage system with two controllers using 2x10G each (the controllers are active/passive, so you can think of it as two separate systems). We would connect controller A with vPC 1x10G to each switch, and controller B in the same way with vPC 1x10G to each switch.
View 2 Replies
View Related
Feb 28, 2012
I am about to configure 4 Gig ports for EtherChannel. I've been reading about EtherChannel and it seems easy enough to configure. I have a host (server)which I am going to connect to these 4 - gig ports. This is new for me and would like some feedback for those that have used EtherChannel on their layer 2 switches. The gig ports will be an access port with VLAN XX.
View 6 Replies
View Related
Sep 12, 2012
We upgrade our Internet service in our India office which required a new router. The local vendor suggested an 1841, so that is what we have. It has two fastethernet ports on it.
The ISP (Airtel) provided the following IP address information:
Public WAN IP : 122.181.23.200/30
WAN IP : 122.181.23.202SUBNET MASK : 255.255.255.252GATEWAY : 122.181.23.201Pri DNS : 125.22.47.125Sec DNS : 202.56.250.5
[Code]......
View 5 Replies
View Related
Nov 8, 2012
Configuring OSPFv2 on a Nexus 5K switches, after configuring area 0 or area 10 it shows as 0.0.0.0 or 0.0.0.10 instead, I'm planning to uplink a couple of ASAs with OSPF enabled, just wondering if the area format showing will be a problem, is this how is supposed to look in the Nexus 5K? and will the 5K be able to form adjacensies with other non-Nexus devices that have area 0 and 10?
View 5 Replies
View Related
Jul 20, 2011
getting radius to work on a 2950G switch with an older IOS of 12.1(22)EA1. I have radius setup on a windows 2k8 box and all of my other switches 2960's and above have no issues. I am unable to input the nas-identifier of 32 into the config using - radius-server 32 attribute 32 include-in-access-req format %h as well as the aaa session-id common commands. Doing a debug radius says that the radius server is not defined.
View 5 Replies
View Related
Apr 3, 2008
We're trying to configure our Cisco 4507 (Supervisor Engine IV) to allow a new Dell server with a pair of Broadcom 5708 GigE NIC's to aggregate its NIC's to give us a 2gbps link to the switch.
So far we seem to have got the team and LACP up and enabled, but the adaptor that the Broadcom Admin Util creates for the team is only showing a 1gbps connection where I would have expected it to show as 2gbps.
The individual NICs show as connected at 1gbps. We're not Cisco experts so are struggling on how to get the 2 NICs to aggregate.
On the server side we've done nothing other than create a team using 802.3ad LINk Aggregation using LACP.
This is what I think the relevent output from "sho conf" is, more available if needed.
version 12.2
boot system flash bootflash:cat4000-i9s-mz.122-18.EW1.bin
!
interface Port-channel2
[Code].....
View 3 Replies
View Related
Nov 8, 2011
I have a 4507 cisco switch loaded with two sup-modules.. [code]
View 5 Replies
View Related
Jun 12, 2013
We just received a new C2911 G2 ISR and have been trying to configure the EtherSwitch SM-ES2-24-P module on it. Through the router console, I tried assigning an IP address to the router Gi1/1 interface which I assume is the link to the Etherswitch module but all I'm getting is "IP addresses may not be configured on L2 links" - as per the docs, I should be able to assign an IP address on that "logical" interface link. Any other way for me to configure the ports on that switch module?
View 5 Replies
View Related
Aug 15, 2012
I want to configure management for some Nexus 5548's?I wanted to manage the switches via an SVI. I have read the following document which gives details about the Management SVI but doesn't answer all questions.[URL]I am not running any layer 3 functionality on the switch, no layer3 license (which it mentions in the above link) Will I still be able to create a management SVI. I know I will need to enable the feature 'interface-vlan' to setup a Management SVI, does that require a license?
View 6 Replies
View Related
Jan 16, 2012
IOS we used for limiting access for a group we used configuration of snmp-server views like following
snmp-server group backupgroup v3 priv read backupview write backupview access 20 snmp-server view backupview ccCopyTable included could not find out how to achive this config in NX-OS on Nexus5500
View 2 Replies
View Related
Nov 29, 2011
problem to configure MWAM. I have installed MWAM module in 6506-E slot 2 with sup720-3B. After installing MWAM the Status is PwrDown. I tried to turn on the power but its not happening. MWAM is installed in slot 2 and here is the result of show module 2 My Sup720-eB IOS image is s72033-advipservicesk9_wan-mz.122-33.SXJ1.bin
6506-E#show module 2
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 3 MWAM Module WS-SVC-MWAM-1 SAD081203GK
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 0003.feae.bb8c to 0003.feae.bb93 3.0 Unknown Unknown PwrDown
Mod Online Diag Status
---- -------------------
2 Not Applicable
View 2 Replies
View Related
Nov 17, 2011
I have a Nexus 7000 plus 6 boxes NX2000 on backbone.I have configured on 7000 :
conf t
system jumbomtu 9000
exitERROR: Ethernet111/1/1: requested config change not allowed
...
ERROR: Ethernet122/1/48: requested config change not allowed
1/111/14 is a NX2000 port conf tinterface ethernet 1/111/14 switchport mtu 9000 exit
I have gotten this message : Error: MTU cannot be configured on satellite port(s) - Eth122/1/11 ?I have tried on a NX7000 TP port:ERROR: Ethernet10/45: MTU on L2 interfaces can only be set to default or system-jumboMTU ?Does JUMBOMTU configuration can be done only when there are no NX2000 configured ?
View 1 Replies
View Related
Jan 29, 2013
We have 2x WS-C3560X-48 with the 10Gb SFP C3KX-NM-10G module.I want to use the 10Gb SFP (with a redundant 1Gb link) between each of the switches.Below is the configuration what I think I should use. Is this correct?
SWITCH1
int TE1/1
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode active
[code]....
We also want to utilise Link Agrrigation for the servers that attach to the switch. Would this config be correct?
port-channel load-balance src-ip
int range x
switchport mode access
switchport access vlan 1 (They are all on the default vlan)
spanning-tree portfast
channel-group x mode active
(Then I would configure the LACP config on the server) Is there anything I am missing?
View 9 Replies
View Related
Jan 31, 2012
I have a 3560 8 port switch. Int gi0/9 is trunked to another switch downstream. When I try to configure int gi0/10 to trunk to a switch upstream the interface on the switch goes down and I have to either reboot the switch or plug directly into the switch and telnet into it to turn off trunking on the interface. When I configure trunking on the interface on the upstream switch that connects to this interface the same happens on that switch. The upstream switch is a 3750 with 12 sfp ports. Several interfaces are trunking to other switches from this switch. Spanning tree is not configured on the 3750 at all , and is not configured on either gi0/10 or gi0/9 on the 3560. I was consoled into the 3560 during a reboot after the interface went down, a message came up that said something like "Spanning Tree returning gigabit ethernet 10 to constant state" Why would I get this message if spanning tree is not enabled on the gig ports on either end of the trunk? There is no loop to require spanning tree to shut down an interface. I have several other 3560's configured as I would like to configure this switch and they are trunking without issue.
View 8 Replies
View Related
Jul 24, 2012
Is there any in depth documentation on how to configure a VWIC3-4MFT-T1/E1 card? It will sit in a CISCO2911/K9. The network is point to point T1s - a quantity of four coming into this router.
View 1 Replies
View Related
