I have removed an embbedded service engine modole from an 2951 router, after reboot the rouiter. the service engine interface still appears; any command can I use to completely remove it.
View 2 RepliesSure this is a simple one. New to the 1900 series routers, have a 1921 with IOS 15.1. Noticed that there is a standard interface labeled Embedded-Service-Engine0/0. What the purpose of this is? Cannot seem to find any detail on it. See extract from default config below.
View 5 Replies View Relatedi cann't enable embedded-Service-Engine on cisco2911 router.
View 3 Replies View RelatedIs there any way to add an E1/T1 WIC to the 5915 Embedded Service Router?
Can I add any additional cards to it?
I do not understand where in the CCP I can configure PAT for communication back 7960G VoIP phone with SIP firmware Maybe I'm wrong on the concept of communication pass back to the Voice VLAN.
View 1 Replies View Relatedcan I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
View 2 Replies View Relatedi got some problem configuring my cisco 887VAW internet access point.I want to be able to manage it thru ssh console with the service-module wlan-ap0 session mode. And i want to access thru http but it's not working too I show you my config
This is my config :
Current configuration : 3281 bytes
!
! Last configuration change at 21:43:11 UTC Fri May 18 2012 by jon
! NVRAM config last updated at 21:46:05 UTC Fri May 18 2012 by jon
! NVRAM config last updated at 21:46:05 UTC Fri May 18 2012 by jon
version 15.1
[code]....
Configuring Cisco 2951 router using Cisco Configuration Professional. I have created a zone based firewall on the router and have created a zone policy for network traffic between two LANs or two zones. I need a create a rule for new traffic that should allow a custom user defined service to flow between the two zones associated with with two LANs.
The problem is How do I created a custom service that I can use for the new traffic rule? I created a network service object as shown in the screenshot below:However, when I am adding the new rule, this service object does not appear in the user defined service in the protocols tree box as shown in the screenshot below:
What is the proper way to create a custom user defined service? I was not able to create it using Class map by the way because again I did not find the service object group in the user defined service when creating a class map.
I have a 1t3/e3 card in a new 2951. When I statred the router, I found no interface corresponding to this module when do "show ip interface brief"
View 3 Replies View RelatedI have EEM configured on cisco 3560 switch. The configuration is below. I want that switch inform me through email when device with particilular IP address become unavailable. I already try to debug this with debug event manager action mail but didn't see any output. [code]
View 2 Replies View RelatedAfter I initial MSE with the wizard. MSE take so long to start the service (more than 1 hour) with "Starting MSE Platform, waiting to check the status"Then I decide to reboot the appliance, after that MSE shows the message "Traceback (most recent call last) File "/usr/sbin/yum-updatesd", line 40, in ?import gaminImportError: No module named gaming.
View 7 Replies View RelatedI configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
[code]....
I am currently running a 4506 with a sup V engine. I have purchased a sup 7 engine. Is there a guide on how to perform this task. I am sure I need to do an IOS update as well.
View 2 Replies View Relatedi have a standalone SUP720, no traffic is passing through it. only one port connected for remote telnet, its kind of backup device.today i checked its log, and there are some wiered message.is it a software bug or my SUP has gone bad? [code]
View 24 Replies View RelatedI have recetly upgraded our core switches (6509E) to SUP 2T from 32. Each core has 2 SUP's (hot/standby). out of 4 SUP engines, one is defective. i had received the new SUP from cisco. Currently my core swicth 2 is running with single SUP. Can i directly insert the new SUP engine in slot 6 (free)? will it automatically load the existing IOS from active SUP? what will happen if the new SUP has a different IOS other than the active SUP? Also is there a way to find out the IOS version without inserting in the chasy?
View 2 Replies View RelatedI would like to find out how to upgrade SUP engine 32 via USB port as I've never did IOS upgrade on a SUP engine via USB before
View 5 Replies View RelatedWe have a scenario with 2 chassis, both with 2 supervisor Engine 2T, we try to make a configuration of VSS with the chassis and would link to know if is possible have 2 supervisor on chassis one and 2 supervisors on chassis 2 with VSS?
Router#sho switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = active unit removed
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
[code]....
would like to use the second supervisors for obteind the local redundancy en chassis 1 and 2, this is possible?
the actually version on four supervisors is: s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin
We recently perchaced 4503 switch with Sub Engine 7L. It has universal IOS. We are unable to run EIGRP and HSRP protocol and the switch came with temporal license.how to proceed further to get EIGRP and HSRP enabled on the 4503 switch.
View 8 Replies View Relatedon-plus see the device and allows CPE( imbedded) to start then never opens,,,tried genera connection and used that address supplied to open CCP no discovery.also seems onplus doesn't see a service contract or firmware, etc
View 1 Replies View RelatedI have configured the VSS in two cisco 6509-E series with only one supervisor engine, but if i configured with two supervisor engine. it is going to common mode. One supervisor engine is 3c and 3cxl.
View 2 Replies View RelatedI have an older 4006 with a Supervisor II+. We now need OSPF support, which the Sup II+ does not provide. I have access to a Supervisor III (WS-X4014), which will provide OSPF support. Question is, are there any gotchas to shutting down the switch, replacing Supervisor Engines and then powering up? What about the flash card? On my current system, it appears that I am only using bootflash: , which is where the IOS resides (see below). Since my startup config is in nvram and my IOS is in bootflash, what's the purpose of the flash card in slot0: ? and where does NVRAM and bootflash actually live on a 4006 ( on the Supervisor Engine?)
sh bootvar
BOOT variable = bootflash:cat4500-ipbase-mz.122-31.SGA11.bin,1;,1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
[Code].....
we got a problem with our cat4006 coreswitch. The led on the supervisorengine is red, and several errors are appearing in the message log. [code]
View 1 Replies View RelatedI need to add another SUP engine on Cat 4507R switch, with a new one. I have old SUP engine running in this switch. Sometime this switch is reloaded without any reason. So we want to add another sup engine for redundancy. What is the procedure to do this & also how much outage time would it cause? Which sup engine will be run as primary and which one should be redundancy?
SWITCH-4507#sh ver
Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version
12.2(25)EWA8, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 24-Jan-07 15:28 by pwade
[code]....
I buy a Cisco 4003 Switch with Supervisor Engine I but it only run CatOs and i whant it to run Cisco IOS so whitch Supervisor Engine can the Cisco 4003 Switch run? i have look at the Supervisor Engine III it can run Cisco IOS and Layer 3 but can i use that in my Cisco 4003 switch?
View 14 Replies View RelatedFor C6500 chassis, sup-fould like to know the dirrerence between supervisor engiene 720 sup-bootflash and sup-bootdisk?
View 3 Replies View RelatedOn an existing 4500 switch with a single sup 6-E, another sup 6-E is added. But the second sup6-E comes up as synchronised with active and in a few minutes time, reloads again. the software is 12.2(44) is the same on both sup engines. the redundancy sso output shows that slot6 is disabled.
View 1 Replies View RelatedAny doc for installing the a PoE switch module for a 2951? I find alot about the 2951 PoE Power supply but nothing for the switch module.
View 5 Replies View RelatedI'm trying to set up a 2951 with a 24 port switch module. I want the ports to act similiarly to the ports on an 881 router - where I assign the VLANs on the router and I set the VLANs to the switchport interfaces.I would like to be able to create the VLANs on the router portion of the 2951 and then, enter the switch module and configure the Ports to the VLANs but, how do I logically connect router to the switch? Is it an internal logical interface - meaning how are the VLANs getting from the router to the switch?
View 24 Replies View RelatedIs it possible to configure a Cisco2951 and a Cisco2921 in HSRP?
View 1 Replies View RelatedI see the throughput of a ISR is 296.96 Mbps how would this compare to a 3560 if the figure is 38.7Mpps?
What would the throughput of a 3560 be in Mbps?
We need to give TCP 3389 & 3399 priority over all other traffic between a Cisco 1941 and 2951.What is needed to do this?
View 6 Replies View RelatedWe have purchased a new 2951 router with IOS version 2951-universalk9-mz.SPA.150-1 and we would like to upgrade to c2951-universalk9-mz.SPA.152-2.T.bin.
View 1 Replies View RelatedMy company is doing an nationwide upgrade of it's leased 2951 routers. For security sake I need to wipe everyone of them before being sending them back to the leasing company. I would like to somehow boot to a USB drive and call it a day.
View 4 Replies View Related