Sure this is a simple one. New to the 1900 series routers, have a 1921 with IOS 15.1. Noticed that there is a standard interface labeled Embedded-Service-Engine0/0. What the purpose of this is? Cannot seem to find any detail on it. See extract from default config below.
View 5 RepliesI have removed an embbedded service engine modole from an 2951 router, after reboot the rouiter. the service engine interface still appears; any command can I use to completely remove it.
View 2 Replies View Relatedi cann't enable embedded-Service-Engine on cisco2911 router.
View 3 Replies View RelatedIs there a router (1900-3900 series router) that will support a 100FX fiber connection. We use to use 2800-3800 and 2600-3700 series routers with FX fiber interface now these routers are no longer available and our need for 100Mbps FX is still a requirement.
View 3 Replies View RelatedIs there any way to add an E1/T1 WIC to the 5915 Embedded Service Router?
Can I add any additional cards to it?
I bought 1921-SEC-k9 so i have security license installed: Technology Package License Information for Module:'c1900' [code] Now I'd like to know if SSL VPN comes with that license or do I need to buy additional VPN SSL license to use it? If so.. i'd just use IPsec... i need client-to-site configuration.. can you point me to tutorial or just a basic config.. because for ipsec i just find site-to-site tutorials on internet.
View 8 Replies View Relatedcan I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
View 2 Replies View RelatedI can see the console on the router. (Using the USB console connected to a Macintosh.) I was configuring the router though this console connection, and I created a new user (priv level 15) and removed the default 'cisco' user. So I'm stuck at the username/password login prompt now.
I decided to do the password recovery procedure (via the cisco doc I found etc), but I cannot break into ROMMON during the boot process. I'm not sure if that's because my Mac isn't sending the break, or what.
The pw recovery doc says you can "remove flash" if you can't break into the boot sequence. However, I cannot find any instructions on how to remove the flash. I've opened the router, and I see one very small daughter card on the main board that I think is the flash, but I'm not about to start arbitrarly prying parts off.
I've got a problem with DHCP running on a cisco 1900 series router, 1921 to be precise. The Data VLAN works perfectly, i configured a ip helper address and its working. Problem tough is VLAN 20. This is the voice vlan. As u can see in the config below, this has been configured using VRRP and VRF for failover purposes. I did more of these configurations, and they all worked fine, just not with this particular router!
As u will notice i deleted all the not needed to know information or i X'ed it!
Jan-Aart
version 15.1
service timestamps debug datetime msec
[Code]......
I'm a bit new to Cisco and i find this AAA a bit confusing..I've turend on AAA by:aaa new-model
Can I use this "default" list for WebVPN ? And what would be a different if i create new "sslvpn" list..Also when I'll be creating user for VPN remote access.. that user will also exist in local database and have access to router via SSH?Because the research I've done it doesn't seem you can group users in different "aaa groups" e.g. user admin belongs under "admin" aaa group which can do ssh to router, users for VPN can only do remote VPN access and not SSH and login into router.i saw ASA has some attribute for users called remote-user
•admin, in which users are allowed access to the configuration mode. This option also allows a user to connect via remote access.
•nas-prompt, in which users are allowed access to the EXEC mode.
•remote-access, in which users are allowed access to the network.
But i can't find this option in IOS on my 1900 Series ISR router.
We have been using a dhcp and tftp server to automatically configure branch WAN routers such as 1751's and 1841's for years but, have recently purchased a 1921 and 1941 as possible next generation replacements. The problem is when the 1900 series power up instead of getting a dhcp address directions to the tftp server it boots up and asks for the user name to be immediately changed or you will be "locked out". Any workaround to this so that I can again go back to download my common configuration? Or any other way of automatically configuring the newer version ios? Doing extra steps for 500 WAN branch routers is time consuming. Doing configurations without automation for that many is moving in the wrong direction.
View 1 Replies View RelatedAfter I initial MSE with the wizard. MSE take so long to start the service (more than 1 hour) with "Starting MSE Platform, waiting to check the status"Then I decide to reboot the appliance, after that MSE shows the message "Traceback (most recent call last) File "/usr/sbin/yum-updatesd", line 40, in ?import gaminImportError: No module named gaming.
View 7 Replies View Relatedi have a cisco 1900 series router from the isp and we connect it the our router the rv042 small biz, and we have here a cisco catalyst 2950 switch with just default configuration connected to the hosts.
my problem is from time to time that the connection is lost there is no connection with the router and the only solution is to turn off and on the cisco 1900 router and the connection will be back.
do we need to configure the routers and switches? what do you need to configure?
I have a strange issue with 4500 E chassis loaded with SUP 7L-E which always remains in ORANGE LED status, also the uplink ports interface is down and the line protocol is down but when i execute the command sh int gig1/5 it show me the media type sfp but there is no red laser light seen in the sfp transiever,The below command is configured for the uplink gig port on the SUP engine.hw-module uplink select gigabitethernet?
View 10 Replies View RelatedOur company will go to buy a core switch 4503. What is the difference between the Catalyst 4500 E-Series Supervisor 7L-E and the Catalyst 4500 E-Series Supervisor 7-E?
View 1 Replies View RelatedCisco 1900 , 2900 and 3900 have Interface Slots and Service Module Slots , My question is which type of card is support this slot.
View 6 Replies View Relatedalthough cisco sw advisor said that the best IOS for my hardware 6509 Sup720 IOS: (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF16 suits the WiSM; And I tested it already with WiSM version 5.0 but when I've upgraded the WiSM to version 6.0 the service interface from the switch side says:
B5_Noc2_CS1(config)#int gig 4/9
% This interface cannot be modified
as the customer refuse to upgrade the switch IOS & He wants to use the latest ED WiSM sw 6.0;
Can i do sub-interface in cisco 891 or 881 series router ? 1900 and 2900 series router support sub-interface ?
View 1 Replies View RelatedI have configured Cisco 870 router ATM interface with following configuration
interface atm 0
ip address public ip 255.255.255.254
ip nat outside
pvc 0/38
encapsulation aal5snap
no shutdown
But when I check ATM interface it is still down and line protocol is down. how to make it up and up so that internet service could be used.Also I want to know that the provider has also given username and password for internet in their device.We want to replace that device with the router and facing problems.
does the Cisco 7600 Series SPA Interface Processor-600 (7600-SIP-600-DC) only support a single SPA, e.g. 1 x SPA-OC192POS-XFP?
The 10Gbps through put on the 7600-SIP-600-DC and [URL]to show that this is the case.
I am looking for a config, as per the attached diagram, if the traffic comes from FE01 it should go via FE03 for the internet and when the traffic comes from FE02 it should go via FE04 for the internet.
View 1 Replies View RelatedI have autonegotiation disable on my interfcae what should be duplex setting on other end?
Router#sh run int Gi0/3/0
Building configuration...
Current configuration : 334 bytes(code)
I have to bridge 1400 series which in the virtual interface has a CRC errors, i don´t the reason, maybe the link (point-point bridge) is misaligned.
View 3 Replies View RelatedI was able to setup my router c819 with Verizon 3G but there is one minor thing that on the console it keeps saying:
Aug 7 21:04:30.067: %LINK-5-CHANGED: Interface Cellular0, changed state to reset
Aug 7 21:04:35.111: %LINK-3-UPDOWN: Interface Cellular0, changed state to down
Aug 7 21:06:18.423: %LINK-3-UPDOWN: Interface Cellular0, changed state to up
The interface Cellluar0 is connected to Verizon 3G network and I'm able to ping and get to the internet just fine. I did few research and some people said it was access list. My ACL is below but I can't find anything wrong with it.
!
!
interface Cellular0
ip address negotiated
[Code].....
We are facing an issue with a customer where a Cisco 4400 Series controller is blocking the 802.11a/n Radio Interface of a 1250 AP. The radio shows as down on the controller GUI. The error message on the GUI is that the 'Regulatory Domain' is not supported. This can be seen from the attached screenshot. Also relevant parts of the WLC configs are attached. WLC: Cisco 4402 WirelessWLC Country: SADevice: Cisco Lightweight Access Point 1250 (LAP) is controlled through the 4402 Cisco Wireless LAN Controller (WLC)The operating system version of the LAP: c1250-k9w8-mx.124-18a.JA version of the WLC: Software Version 5.2.178.0 The problem is that the controller shows that the 802.11a/n Radio Interface in Radio Slot # 1 is always down , the customer tried to manually 'no shut' the AP interface from the console and it worked , but obviously this solution would not work as the configuration cannot be saved (LW AP).
View 12 Replies View Relatedwe have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]
Q. Does the Supervisor 720 support all existing Cisco Catalyst 6500 series interface and services module, protecting customer investments?
View 1 Replies View RelatedWhen I create a service object or group and add the object to a new rule it never works.I mean the traffic match not the rule. I see not hits.I placed the rule on top of my access list to check if I do somethink wrong but it is not working. When I place only a service for example tcp/23 it is working.
my ip service object
object-group service g-as400 description access client 2 as400 machine service-object tcp-udp destination eq 397 service-object tcp destination eq 137 service-object tcp destination eq 2001 service-object tcp destination eq 3000 service-object tcp destination eq 445 service-object tcp destination range 446 447 service-object tcp destination eq 449 service-object tcp destination eq 5010 service-object tcp destination eq 5544 service-object tcp destination eq 5555 service-object tcp destination range 8470 8476 service-object tcp destination eq 8480 service-object tcp destination eq
[code]...
I'm trying to use EPC on ASR1001 running IOS-XE 3.4, and it won't work. Configuration commands are accepted by the router, but there are no packets in the capture buffer.In release notes for IOS-XE, in the 2.5 section, there is a statement that EPC is not supported on ASR1k. Is it true also for newer versions of IOS-XR?
View 1 Replies View RelatedSetting up a new 1941w router. Already have another one offsite that's working great. Based the new configuration on the one I have working and can route traffic, etc. My problem with this new one is that I cannot get into the embedded AP to configure. My configuration follows this question. I have checked status of the interfaces and everything is up except VLAN2. I've used the command no shutdown within the VLAN2 interface, but the operational status is still reading down. The admin status is reading up. All other interfaces are up and up. [code]
View 3 Replies View RelatedI have a need to capture traffic on an ASR 1001 subinterface, but what I have found is that the Embedded Packet Capture feature is not supported on this platform. Are there any simple alternatives to capture egress traffic on a subinterface or am I SOL? This is a walk in the park on normal IOS routers...
View 1 Replies View RelatedCan the embedded AP be configured as a standalone AP without configuring the router's functions? I need to configure one temporarily until we get the 1252AP for the location.
View 1 Replies View RelatedI do not understand where in the CCP I can configure PAT for communication back 7960G VoIP phone with SIP firmware Maybe I'm wrong on the concept of communication pass back to the Voice VLAN.
View 1 Replies View Related