Cisco WAN :: Can Do Sub-interface In 891 / 881 Series Router
Jun 18, 2012Can i do sub-interface in cisco 891 or 881 series router ? 1900 and 2900 series router support sub-interface ?
View 1 Replies
ADVERTISEMENT
Cisco WAN :: Configuring 870 Series Router ATM Interface
Nov 24, 2011I have configured Cisco 870 router ATM interface with following configuration
interface atm 0
ip address public ip 255.255.255.254
ip nat outside
pvc 0/38
encapsulation aal5snap
no shutdown
But when I check ATM interface it is still down and line protocol is down. how to make it up and up so that internet service could be used.Also I want to know that the provider has also given username and password for internet in their device.We want to replace that device with the router and facing problems.
Cisco WAN :: Duplex Setting On WAN Interface On ASR 1000 Series Router
Apr 13, 2013I have autonegotiation disable on my interfcae what should be duplex setting on other end?
Router#sh run int Gi0/3/0
Building configuration...
Current configuration : 334 bytes(code)
Cisco WAN :: 1900-3900 Series Router With 100FX Fiber Interface
Oct 30, 2011Is there a router (1900-3900 series router) that will support a 100FX fiber connection. We use to use 2800-3800 and 2600-3700 series routers with FX fiber interface now these routers are no longer available and our need for 100Mbps FX is still a requirement.
View 3 Replies View RelatedCisco Switching/Routing :: Router 800 Series Interface Cellular0 Keeps Bouncing Up / Down
Aug 6, 2012I was able to setup my router c819 with Verizon 3G but there is one minor thing that on the console it keeps saying:
Aug 7 21:04:30.067: %LINK-5-CHANGED: Interface Cellular0, changed state to reset
Aug 7 21:04:35.111: %LINK-3-UPDOWN: Interface Cellular0, changed state to down
Aug 7 21:06:18.423: %LINK-3-UPDOWN: Interface Cellular0, changed state to up
The interface Cellluar0 is connected to Verizon 3G network and I'm able to ping and get to the internet just fine. I did few research and some people said it was access list. My ACL is below but I can't find anything wrong with it.
!
!
interface Cellular0
ip address negotiated
[Code].....
Cisco WAN :: 7600 Series SPA Interface Processor-600 Compatibility
Oct 3, 2012does the Cisco 7600 Series SPA Interface Processor-600 (7600-SIP-600-DC) only support a single SPA, e.g. 1 x SPA-OC192POS-XFP?
The 10Gbps through put on the 7600-SIP-600-DC and [URL]to show that this is the case.
Cisco WAN :: Interface Embedded-Service-Engine In 1900 Series
May 3, 2011Sure this is a simple one. New to the 1900 series routers, have a 1921 with IOS 15.1. Noticed that there is a standard interface labeled Embedded-Service-Engine0/0. What the purpose of this is? Cannot seem to find any detail on it. See extract from default config below.
View 5 Replies View RelatedCisco WAN :: Routing Based On Source Interface FE01 Series
Jun 6, 2011I am looking for a config, as per the attached diagram, if the traffic comes from FE01 it should go via FE03 for the internet and when the traffic comes from FE02 it should go via FE04 for the internet.
View 1 Replies View RelatedCisco Wireless :: Interface Radio0-802.11A With CRC Errors 1400 Series
Nov 1, 2011I have to bridge 1400 series which in the virtual interface has a CRC errors, i don´t the reason, maybe the link (point-point bridge) is misaligned.
View 3 Replies View RelatedCisco WAN :: Can't Use Ehwic-3g-hspa-u Card In 2800 Series And 1841 Series Router
Jun 2, 2012why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedCisco WAN :: 1700 Series Router To 2811 Series Router / Going From T1 To Ethernet?
Jan 17, 2011I have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies View RelatedCisco Wireless :: 4400 Series Controller Blocking 802.11a/n Radio Interface Of 1250 AP
Dec 19, 2009We are facing an issue with a customer where a Cisco 4400 Series controller is blocking the 802.11a/n Radio Interface of a 1250 AP. The radio shows as down on the controller GUI. The error message on the GUI is that the 'Regulatory Domain' is not supported. This can be seen from the attached screenshot. Also relevant parts of the WLC configs are attached. WLC: Cisco 4402 WirelessWLC Country: SADevice: Cisco Lightweight Access Point 1250 (LAP) is controlled through the 4402 Cisco Wireless LAN Controller (WLC)The operating system version of the LAP: c1250-k9w8-mx.124-18a.JA version of the WLC: Software Version 5.2.178.0 The problem is that the controller shows that the 802.11a/n Radio Interface in Radio Slot # 1 is always down , the customer tried to manually 'no shut' the AP interface from the console and it worked , but obviously this solution would not work as the configuration cannot be saved (LW AP).
View 12 Replies View RelatedCisco WAN :: 6500 Series Switch / Configured Port Channel On Both Switches With 2 Gig Interface
Jan 9, 2012we have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]
Cisco Switching/Routing :: Does Supervisor 720 Support All Existing Catalyst 6500 Series Interface
Feb 12, 2013Q. Does the Supervisor 720 support all existing Cisco Catalyst 6500 series interface and services module, protecting customer investments?
View 1 Replies View RelatedCisco WAN :: 1841 Router - HWIC Interface Card - Cannot See Interface In Configuration File
May 9, 2012i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies View RelatedCisco WAN :: Set Up WAN Interface On Fast Ethernet Interface Of 877 Adsl Router
Apr 9, 2011Is it possible to set up a WAN interface on a FastEthernet interface of a Cisco 877 Adsl Router ?Due to my ISP, i've to use an external VDSL modem and must connect it to my cisco 877 router (and leave it's adsl interface unused).But i don't know how to set up a wan port, other than the adsl interface itself (dialer0), on my cisco.
View 7 Replies View RelatedCisco Wireless :: Controller 4400 Series Work With Aironet 3600 Series
Mar 6, 2012Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedCisco Wireless :: 1140 AP Series Vs 1260 AP Series Technical Differences
Jul 24, 2012What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedCisco Routers :: How Does Quality And Longevity Of SRP500 Series Compare To RV Series
May 27, 2012My Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedCisco :: Does WLC 2500 Series Supports 1262 Series Access Point
Jun 14, 2011Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedCisco Switching/Routing :: Router Boots Into Router With 2500 Series
Jul 27, 2009I m having 2500 series router. when i boot router automatically get into router(boot)> . how to solve?
View 6 Replies View RelatedCisco WAN :: Multiple VRF For 892 Series Router
Sep 18, 2012i am proposing cisco 892 series router for multi VRF Configurations-MPLS. Is there any challenge you foresee in this architecture.
View 4 Replies View RelatedCisco WAN :: Setup 3G For Router 819 Series
Jul 2, 2012I have a router 819 with 3G built-in. Are there any manual for how to setup the interface celluar 0 for this router out there? I have Verizon as my 3G provider.
View 4 Replies View RelatedCisco WAN :: QoS On 7600 Series Router
Oct 18, 2012I am looking for the best QoS method for a 7600 series router. We have a 7604 edge router that has remote branch connections to it via GRE tunnels. unfortunately I cannot shape on these GRE tunnels neither can I use bandwidth or priority statements.
View 1 Replies View RelatedCisco WAN :: 800 Series Router Basic Configuration
Sep 4, 2012I have just bought my first non-domestic router, a CISCO 887VA-K9 which needs basic configuration to get it working. I have a copy of the configuration guide (334 pages) and CP Express user's guide (94 pages) and have spent an hour reading but either they are missing something or my brain is too small to figure out step 1. How to get started. Perhaps from where to download a CP Express installation kit for Windows.
Is the only way via a terminal emulator connected via a serial port ? Is there a graphical interface I can use ? Are there any basic tutorials for beginners ? This is probably the only non-domestic routrer I shall work on so I don't want to invest in a full training course. I just need enough to plug in the ISP credentials and set up DHCP.
Cisco WAN :: 1800 Series Router Configuration?
Jun 9, 2013load balancing and automatic failover between two isp
View 13 Replies View RelatedCisco Routers :: Using RV042 In Series With Another Router
May 16, 2012I have been able to put two Linksys routers in series no problem but this doesn't seem to work with an RV042.I have a number of customers that need to connect to a private email network via a router based VPN, but since VPN traffic is not filtered in the firewall, I would like to use an older Linksys router to manage the VPN(s) and have it pass data in through the filters of an RV042 on the DMZ port.I am getting stuck on the very frist part of this. Although I can connect to both the RV042 and LinkSys directly (by adjusting my subnet), I cannot ping the Linksys when it is connected through the DMZ port even if I disable the RV042 Internet port.
I know both the Internet and DMZ ports work on the RV042. I suspected that perhaps the RV won't pass through private IPs and tried known available pubic IPs instead of the 192.168.2.x subnet, but still no ping.What would be limiting the RV in this case? Is is possible to setup the RV to work in series with another router? Is there any other way to filter VPN traffic?
Cisco WAN :: 3825 - HSRP Between Two Different Series Router
Mar 8, 2011I want to configure HSRP between two different series routers. In my case the router are 3825 and 3925.
View 7 Replies View RelatedCisco WAN :: 2800 Series Router IOS Is Not Loading?
May 7, 2013i have one cisco router 2811 now its not booting normally.
Router was working without any problems but due to power loss router restarted and goes into rommon mode
I tried to boot from flash and usbfalsh with different images but no use router is in still rommon mode.
here the output of my router:
program load complete, entry point: 0x8000f000, size: 0x3117470
Error : compressed image checksum is incorrect 0x8E095E7F
Expected a checksum of 0x8E0AE77F
*** System received a Software forced crash ***
signal= 0x17, code= 0x5, context= 0x80014e20
[Code].....
Cisco WAN :: 880G Series Router For 3G And Voice?
Mar 15, 2011I have few queries abou the Cisco 880G series router.
1) Suppose if we have a 3G service enabled SIM card then can we insert the same on the Cisco 880G router and browse internet from the LAN of 880G?
2) I think the HSPA+ standard supports 84 Mbps downlink speed..... so is it supported on 880 G router?
3) Can we configure Cisco 880G as a CME?
Cisco WAN :: OC3 Card For 7200 Series Router
Sep 12, 2012One of my customer is looking for 1 port OC3 card for 7200 series router. There are two options (PA-POS-2OC3/PA-A6-OC3)However my customer is not sure whether he wants a ATM/POS card.
How to determine whether i should go for ATM or POS Card for OC3. Or atleast what should be my approach to determine whether i should go for ATM or POS Card for OC3.
Cisco WAN :: 800 Series Router Auto-sense ATM Pvc
Jan 30, 2012Some of which use snap and some use mux, the router is the one will start the connection and will always be on, untill there is a power cut, if there is. At this point when the power comes back on and a packet's destination is the outside the router should initiate a connection over the atm.
•Do not use this feature on a router that initiates PPPoA sessions.
•This feature supports ATM PVCs. Switched virtual circuits (SVCs) are not supported.
•PPPoA does not support static IP assignments within virtual templates.
The second and thrid I can understand and the 3rd will just get assigned an IP address from the ISP.But with the first point how is it possible to set this up when the router cannot initate the connection?
Cisco WAN :: Basic Config Of 860 Series Router
Jan 23, 2011Had no problem getting into IOS via Terminal and changing the host name, username and password. Then I loaded the Cisco CP Express onto a system and got into the web config. Problem is....the default IP is 10.10.10.1 / 255.255.255.248 and I wanted to change it to 192.168.1.1 / 255.255.255.0 I did it in the web interface and it applied to the router, but after that I could never bring up the web interface again on 192.168.1.1. Checking IOS showed that the new 192.168.1.1 did indeed "take". I even added an access list for the 192.168.1.0 network.
View 8 Replies View Related