Cisco WAN :: 800 Series Router Basic Configuration
Sep 4, 2012
I have just bought my first non-domestic router, a CISCO 887VA-K9 which needs basic configuration to get it working. I have a copy of the configuration guide (334 pages) and CP Express user's guide (94 pages) and have spent an hour reading but either they are missing something or my brain is too small to figure out step 1. How to get started. Perhaps from where to download a CP Express installation kit for Windows.
Is the only way via a terminal emulator connected via a serial port ? Is there a graphical interface I can use ? Are there any basic tutorials for beginners ? This is probably the only non-domestic routrer I shall work on so I don't want to invest in a full training course. I just need enough to plug in the ISP credentials and set up DHCP.
View 27 Replies
ADVERTISEMENT
Jan 23, 2011
Had no problem getting into IOS via Terminal and changing the host name, username and password. Then I loaded the Cisco CP Express onto a system and got into the web config. Problem is....the default IP is 10.10.10.1 / 255.255.255.248 and I wanted to change it to 192.168.1.1 / 255.255.255.0 I did it in the web interface and it applied to the router, but after that I could never bring up the web interface again on 192.168.1.1. Checking IOS showed that the new 192.168.1.1 did indeed "take". I even added an access list for the 192.168.1.0 network.
View 8 Replies
View Related
Oct 21, 2011
step by step ACS 5.1's basic configuration through CLI?
View 2 Replies
View Related
Jan 3, 2013
I am struggling to get this working after spending many hours looking at it I am now completely stuck. We are upgrading from a 857W to this 887 VA-M I have some experience of IOS and the 800 series. Our 857W works perfectly using almost the same config. Our situation is that the router will sit in front of our firewall and act essentially as a simple router passing everything through to our Firewall. Nat is done at the Firewall.
We currently have the following configuration that seems to connect the the ISP fine but I cannot connect to the vlan2 port on the switch the firewall cannot connect to he internet or route anything via the Vlan2 port no pings etc.. I am using Fast Ethernet 0 as the Vlan2 port and the rest are V LAN 1 with a local network address to allow me to connect a laptop.
We have a block of static IP addresses, the base of which is assigned to the V LAN 2 interface and used by Dialer 0 as IP Unnumbered. Config below.
4590 out of 262136 bytes
! Last configuration change at 17:42:06 UTC Thu Jan 3 2013
! NVRAM config last updated at 17:43:00 UTC Thu Jan 3 2013
! NVRAM config last updated at 17:43:00 UTC Thu Jan 3 2013
[ code].....
View 2 Replies
View Related
Sep 30, 2011
I have an ASA running 8.2(2).I am trying to get the network on the inside interface to be able to communicate through the outside interface and on to the internet.
View 18 Replies
View Related
Apr 19, 2011
I am trying to set up my Cisco 520 router with a firewall that will: Allow port 80 traffic to the vlan 20,Block all other incomming ports to vlan 20 (unless initalised from inside),Allow all outgoing ports on vlan 20,Block all access from vlan 20 to vlan 10 (unless initalised from vlan 10)
View 35 Replies
View Related
May 8, 2011
creating a DMZ with my current configuration. Most of my configuration has been through the ASDM as I am still learning. I'm looking for a good tutorial through the ASDM to get me on my way. What I need to accomplish is this:
I have an internal GIS server which needs to have a constant database connection to an remote GIS Server which is already configured. I've got a separate VLAN setup on my 3750 switch which connects to the DMZ configured port on my ASA with a security level of 50. My GIS server has been placed in the DMZ VLAN which is accessible from my internal clients. I have a /30 Internet block which is being used for Internet and VPN. I have a separate /28 block that I'm assuming I'll need for the DMZ to work properly.
View 1 Replies
View Related
Oct 12, 2011
I dint have any experience in Using cisco pix firewall. i got this for home lab practice.the pix can be accessed and configured by web based and CLI mode right. basic configuariton tto configure pix 515e in cli mode.
as of now im using console( hyper terminal) to access the pix. in cli based commands i need the following
1. how to assign ip address to inside ethernet and outside ethernet
2. how to enable telnet and after enabling it , can i connect my pc directly to the pix inside ethernet and do telnetting or if at all possible with (https enabled)web based config. any of these are ohk.
went at browsing to find these all i could find is web based configs. i need cli commands.
View 9 Replies
View Related
May 21, 2012
This is my 1st time trying to configure an ASA.
I'm trying to establish a very basic connection (ping) between 2 laptops, one sat on the outside interface, and one on the inside as per the diagram below:
I can ping back and forth from the ASA to 192.168.1.4, and to 10.1.1.1. However, what I'm trying to achieve is to be able to ping from 10.1.1.1 to 192.168.1.4 and vice versa.
I have attached the configuration file with this post as well.
View 4 Replies
View Related
Jan 3, 2013
I have an 871 and all I need to do is some basic rules. Here is the config I am having the issue with.
View 1 Replies
View Related
Dec 13, 2012
in lab trying to run a test upgrade of an Ace30,can seem to get it right ace30 is in slot 1 of the 6500, management vlan 10
View 4 Replies
View Related
Aug 12, 2012
I set up a basic Linksys E2500 with the following information and connected to the internet straight away without a problem: I have spent several hours simply trying to get this basic information into the Cisco 819 using CP Express without success, i.e. I get no internet. Rather than show my inputs, What is the correct setup. I am a novice so I'd rather solve this issue using CP Express just to get connected in the first instance. I have a static IP address, I connected the ethernet cable carrying the internet to the internet port of the E2500 and an ethernet cable from one of the ethernet ports of the E2500 to my PC. For the 819, I connected the internet cable to the GE WAN 0 port and the PC to one of the FE ports.
View 18 Replies
View Related
Jul 19, 2012
We currently have 7 Cisco 3524-XL switches (10-12+ yrs old) which are 10/100. We purchased a handful of Cisco 3750X switches to replace them going with the whole stackwise and redundant power supplies. Our current configuration on the old 3524 switches is that they have hardset all the ports on them to 100MB/FULL since devices would auto-neg to 100/Half. Since we're going from 10/100 to 10/100/1000 switches, I want things to auto-neg as I have heard in the past and experienced that things work better when it auto-neg to gigabit. My upper management is afraid since the old switches wouldn't auto-neg correctly that we should hard set all the ports on the new switches, which would be a nightmare since some ports would be hard set to 100/FULL others to 1000/FULL, etc.. We've tested just about all of our devices at auto with the switches and they've all auto-neg to the correct speed. In short, is Auto-Negotiation the way to go with the newer switches or is it still better practice to hard set your ports?
View 3 Replies
View Related
Apr 8, 2012
I teach in a High School and we've got about a 300 node MS Windows Network. Two MS2003 File Servers act as my DNS/WINS/DHCP servers. We have been using a WATCHGUARD FIREBOX III to act as the router/gateway between the outside external address and my internal (10.0.0.1) gateway address. All p.c's inside the network are routed to one of the Servers (10.0.0.2 or 10.0.0.4) for DNS/WINS/DHCP addressing. The servers point to 10.0.0.1 for gateway.
We are trying to replace the Watchguard Firebox with a CISCO ASA 5505 (eventually we'd like to implement VPN). When I connect the CISCO ASA, I get no internet passthrough at all.
View 1 Replies
View Related
Dec 16, 2011
I have a Cisco 2600 with IOS 12.3. I need a very basic configuration to allow traffic between two LANs. To test this I cleared the router config to the factory default state and configured my network addresses on the interfaces.
When I connected a PC to each interface I found they could ping each other, I was expecting to have to write ACLs to permit the traffic into the interfaces, thinking that the default behaviour of the router would be to deny access. default bahaviour without any ACLs or other routing configurations?
My config, such as it is, is as follows:
Current configuration : 770 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 5 Replies
View Related
Aug 5, 2012
I am trying to configure a Cisco 1841 to allow the users to access the internet. This is my first step with ppp. All the rest of the configuration is ok but I don't know how to setup the interfaces Dialer0 and ATM0/0/0.
Need very basic configuration that I can analyze and use on my device?
View 10 Replies
View Related
Apr 22, 2012
I am replacing a cisco linksys router with a 1941w.
I have the 0/0 accepting a DHCP from the ISP then I have 0/1 going to a switch and hosting a dhcp server.
Where I have an issue is:
A) Finding a way to turn on the wireless and make it use the same DHCP as wired and setting up a user name/wep password
B) Turning on the GUI that is supposed to be embedded on this.
C) Finding a way to make the DNS point to the default gateway so that I don't have to set the address everytime we move the box.
Here is my current configuration, and with it I can get onto the wired network and get to the internet.
Current configuration : 4712 bytes
!
! No configuration change since last restart
version 15.1
[Code]...
View 6 Replies
View Related
Jan 1, 2013
First time user of cisco hardware and we just purchased the 4900m catalyst switch. My question is very general. I am simply hoping to network 3 servers together and I do not wish to do any fancy or advanced configuration. Can I simply use the web management interface for network administration and setup? I just downloaded the Catalyst 4500 Series Switch Cisco IOS software configuration guide and they talk about Cisco View network management system, is this my answer or is this what most people use for basic configuration and administration?
View 3 Replies
View Related
Jun 9, 2013
load balancing and automatic failover between two isp
View 13 Replies
View Related
Jun 13, 2012
about to install first UC320w and wanted some sample 800 series router configurations showing required port fowarding, ACL entries and QoS examples.
View 5 Replies
View Related
Dec 12, 2010
Am trying to do a dynamic configuration of a 3900 series router (3925 to be precise).For the software and licenses, under the IOS technology Package Licenses, what's the significant of SL-39-DATA-K9 and SL-39-SECNPE-K9? Are they really necessary for the router?
View 3 Replies
View Related
Aug 6, 2011
Can we terminate 2 WAN link first Lease line and second Broadband internet link on 800 series router . As 800 series router have only 1 wan port and 4 switch port. Also we want to Configure load balancing over the 2 WAN link, is it possible or Basic router for SMB.
View 1 Replies
View Related
Jan 4, 2012
I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies
View Related
Jun 2, 2012
why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies
View Related
Jan 17, 2011
I have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies
View Related
May 1, 2013
I've goggled and searched here, and I can't seem to find what I'm looking for. I need to make a couple changes to a clients Cisco 800 series router, enable ping replies add ip addresses to the ssh ACL.I can't seem to find any basic commands for CLI anywhere.
View 2 Replies
View Related
Oct 11, 2012
I know we can use copy & Paste, my questions are:
1. Before that, do I need to wipe out the existing confi on the brand new switch?
2. About using TFTP, how does this new switch connects to the TFTP? Does it mean I have to assign a real IP and put it on our network?
View 3 Replies
View Related
Dec 25, 2012
I was trying to configure my Catalyst Express 500 switch (PID VID: WS-CE500-24LC V01) and i followed the step i found in a document on Cisco website but still it showed an error "Page not found" and address displayed on bar was"169.254.0.1/catalyst-express.htm).
View 1 Replies
View Related
Jul 17, 2012
I work for a company that buys used cisco equipment and we are trying to get a basic test center set up. What is the best way to perform basic router testing? We have been trying to come up with something for about 3 weeks and so far all we can do is get in the configuration and play around.
View 1 Replies
View Related
Jan 8, 2013
We have been using a dhcp and tftp server to automatically configure branch WAN routers such as 1751's and 1841's for years but, have recently purchased a 1921 and 1941 as possible next generation replacements. The problem is when the 1900 series power up instead of getting a dhcp address directions to the tftp server it boots up and asks for the user name to be immediately changed or you will be "locked out". Any workaround to this so that I can again go back to download my common configuration? Or any other way of automatically configuring the newer version ios? Doing extra steps for 500 WAN branch routers is time consuming. Doing configurations without automation for that many is moving in the wrong direction.
View 1 Replies
View Related
Jul 9, 2012
I would like to implement simple QOS between two C881 Ethernet router.There are a GRE over IPSec Tunnel between both and 2 vlans configured on it (data & voice).The fa4 is connected to a modem, and a dialer is configured with the PPP account provided by the ISP.The DSL line is a 30 Megas bits download and 2 Megas bits upload.This is my config on one side (the other is the same with reversed) WITHOUT QOS CONFIG injected.
This config works fine. [Code] ....
View 3 Replies
View Related
Nov 27, 2011
My neighbor is using my Belkin Router the basic one and has comcast. We both use his internet and have had no problems until the past 3 days. He just got the home phone service from comcast and the phone line is setup through the modem. Ever since comcast came to his apartment and set this up the home phone service to his modem the router is connected but there is no internet access. What is going on and how can I fix this. He has an HP with windows Vista and I have a Toshiba Satellite L675 that has Windows 7 Home premium edition on it.
View 1 Replies
View Related
Jan 14, 2008
I have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed." I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it.
View 9 Replies
View Related
