Cisco :: Basic Ace30 Configuration For Management Access
Dec 13, 2012in lab trying to run a test upgrade of an Ace30,can seem to get it right ace30 is in slot 1 of the 6500, management vlan 10
View 4 Replies
ADVERTISEMENT
Cisco Application :: ACE30 Running But Not Allowing Management Access
Sep 9, 2012We've got pairs of ACE30s in our data centers set up with active/standby FT. Some time yesterday the active ACE in one data center started refusing management traffic - it accepts SSH connections but fails authentication (local password, no RADIUS/TACACS is configured); and ANM reports it as down (no XML connectivity),We haven't opened a TAC case yet - someone's on his way over to see whether we can get in through the serial port first - but I'm wondering whether there are any other diagnostics we can gather (will resetting the module form the Sup force a coredump?) before we do.
View 2 Replies View RelatedCisco Application :: Accessing ACE30 Through Https For Management
Jun 11, 2012I am new to the ACE30. I a basic configuration from the CLI and I am trying to use the device manger. I am able to get to the web informational page rather then accessing the login page. I have rest the password for both the admin and www and still no go. my question is how to go into enabling the GUI access.
View 1 Replies View RelatedCisco Switching/Routing :: 4900M Basic Management Setup
Apr 13, 2010I' ve three 4900M switches equipped with the WS-X4920-GB-RJ45 module and the WS-X4908-10GE module. Now I'm started to setup these switches in our lab environment for the first time. They behave a little bit strange in comparison with the C3750 series which I used before and which I will replace by these powerful machines.
I tried to setup these switches to be managed through the management port. I configured IP address, default route in the management vrf, set the source-interface for tftp,ssh,ftp and tacacs to use the management port. Ping using the manangement port was successful. After finishing theses steps I configured the TACACS and AAA settings accordingly the informations I found on CCO. I tested the settings with "test aaa group authentication" command- without success. On my Cisco ACS no request was received and the switch told me he could't reach the tacacs server. Other switches in the same IP subnet are working without failure, so firewall or server should not be the problem.
Cisco :: 5508 WLC Configuration / Can't Access GUI On Management Interfaces Ip Address
Aug 30, 2011I've got a new 5508 wireless lan controller and can ping the ip address of the management interface, but can't access the GUI at the management interface's ip address. I can access the GUI on the service-port interface. No static routes in the controller; trunk appears to be set up correctly.
View 5 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.1 Basic Configuration Through CLI?
Oct 21, 2011step by step ACS 5.1's basic configuration through CLI?
View 2 Replies View RelatedCisco WAN :: 887VA-M Basic Configuration Non Nat
Jan 3, 2013I am struggling to get this working after spending many hours looking at it I am now completely stuck. We are upgrading from a 857W to this 887 VA-M I have some experience of IOS and the 800 series. Our 857W works perfectly using almost the same config. Our situation is that the router will sit in front of our firewall and act essentially as a simple router passing everything through to our Firewall. Nat is done at the Firewall.
We currently have the following configuration that seems to connect the the ISP fine but I cannot connect to the vlan2 port on the switch the firewall cannot connect to he internet or route anything via the Vlan2 port no pings etc.. I am using Fast Ethernet 0 as the Vlan2 port and the rest are V LAN 1 with a local network address to allow me to connect a laptop.
We have a block of static IP addresses, the base of which is assigned to the V LAN 2 interface and used by Dialer 0 as IP Unnumbered. Config below.
4590 out of 262136 bytes
! Last configuration change at 17:42:06 UTC Thu Jan 3 2013
! NVRAM config last updated at 17:43:00 UTC Thu Jan 3 2013
! NVRAM config last updated at 17:43:00 UTC Thu Jan 3 2013
[ code].....
Cisco :: Basic Configuration For An ASA To Reach The Internet
Sep 30, 2011I have an ASA running 8.2(2).I am trying to get the network on the inside interface to be able to communicate through the outside interface and on to the internet.
View 18 Replies View RelatedCisco WAN :: 800 Series Router Basic Configuration
Sep 4, 2012I have just bought my first non-domestic router, a CISCO 887VA-K9 which needs basic configuration to get it working. I have a copy of the configuration guide (334 pages) and CP Express user's guide (94 pages) and have spent an hour reading but either they are missing something or my brain is too small to figure out step 1. How to get started. Perhaps from where to download a CP Express installation kit for Windows.
Is the only way via a terminal emulator connected via a serial port ? Is there a graphical interface I can use ? Are there any basic tutorials for beginners ? This is probably the only non-domestic routrer I shall work on so I don't want to invest in a full training course. I just need enough to plug in the ISP credentials and set up DHCP.
Cisco WAN :: 520 Basic Firewall Configuration With DMZ Required
Apr 19, 2011I am trying to set up my Cisco 520 router with a firewall that will: Allow port 80 traffic to the vlan 20,Block all other incomming ports to vlan 20 (unless initalised from inside),Allow all outgoing ports on vlan 20,Block all access from vlan 20 to vlan 10 (unless initalised from vlan 10)
View 35 Replies View RelatedCisco Firewall :: Basic DMZ Configuration On ASA 5510
May 8, 2011creating a DMZ with my current configuration. Most of my configuration has been through the ASDM as I am still learning. I'm looking for a good tutorial through the ASDM to get me on my way. What I need to accomplish is this:
I have an internal GIS server which needs to have a constant database connection to an remote GIS Server which is already configured. I've got a separate VLAN setup on my 3750 switch which connects to the DMZ configured port on my ASA with a security level of 50. My GIS server has been placed in the DMZ VLAN which is accessible from my internal clients. I have a /30 Internet block which is being used for Internet and VPN. I have a separate /28 block that I'm assuming I'll need for the DMZ to work properly.
Cisco Firewall :: Pix 515e Basic CLi Configuration
Oct 12, 2011I dint have any experience in Using cisco pix firewall. i got this for home lab practice.the pix can be accessed and configured by web based and CLI mode right. basic configuariton tto configure pix 515e in cli mode.
as of now im using console( hyper terminal) to access the pix. in cli based commands i need the following
1. how to assign ip address to inside ethernet and outside ethernet
2. how to enable telnet and after enabling it , can i connect my pc directly to the pix inside ethernet and do telnetting or if at all possible with (https enabled)web based config. any of these are ohk.
went at browsing to find these all i could find is web based configs. i need cli commands.
Cisco Firewall :: ASA5520 Basic Configuration
May 21, 2012This is my 1st time trying to configure an ASA.
I'm trying to establish a very basic connection (ping) between 2 laptops, one sat on the outside interface, and one on the inside as per the diagram below:
I can ping back and forth from the ASA to 192.168.1.4, and to 10.1.1.1. However, what I'm trying to achieve is to be able to ping from 10.1.1.1 to 192.168.1.4 and vice versa.
I have attached the configuration file with this post as well.
Cisco Firewall :: 871 Configuration - Basic Rules
Jan 3, 2013I have an 871 and all I need to do is some basic rules. Here is the config I am having the issue with.
View 1 Replies View RelatedCisco WAN :: Linksys E2500 - Basic Configuration Of 819 Using CP Express
Aug 12, 2012I set up a basic Linksys E2500 with the following information and connected to the internet straight away without a problem: I have spent several hours simply trying to get this basic information into the Cisco 819 using CP Express without success, i.e. I get no internet. Rather than show my inputs, What is the correct setup. I am a novice so I'd rather solve this issue using CP Express just to get connected in the first instance. I have a static IP address, I connected the ethernet cable carrying the internet to the internet port of the E2500 and an ethernet cable from one of the ethernet ports of the E2500 to my PC. For the 819, I connected the internet cable to the GE WAN 0 port and the PC to one of the FE ports.
View 18 Replies View RelatedCisco Switching/Routing :: 3750X - Basic Configuration
Jul 19, 2012We currently have 7 Cisco 3524-XL switches (10-12+ yrs old) which are 10/100. We purchased a handful of Cisco 3750X switches to replace them going with the whole stackwise and redundant power supplies. Our current configuration on the old 3524 switches is that they have hardset all the ports on them to 100MB/FULL since devices would auto-neg to 100/Half. Since we're going from 10/100 to 10/100/1000 switches, I want things to auto-neg as I have heard in the past and experienced that things work better when it auto-neg to gigabit. My upper management is afraid since the old switches wouldn't auto-neg correctly that we should hard set all the ports on the new switches, which would be a nightmare since some ports would be hard set to 100/FULL others to 1000/FULL, etc.. We've tested just about all of our devices at auto with the switches and they've all auto-neg to the correct speed. In short, is Auto-Negotiation the way to go with the newer switches or is it still better practice to hard set your ports?
View 3 Replies View RelatedCisco WAN :: ASA5505 Basic Configuration / No Internet Pass-through At All
Apr 8, 2012I teach in a High School and we've got about a 300 node MS Windows Network. Two MS2003 File Servers act as my DNS/WINS/DHCP servers. We have been using a WATCHGUARD FIREBOX III to act as the router/gateway between the outside external address and my internal (10.0.0.1) gateway address. All p.c's inside the network are routed to one of the Servers (10.0.0.2 or 10.0.0.4) for DNS/WINS/DHCP addressing. The servers point to 10.0.0.1 for gateway.
We are trying to replace the Watchguard Firebox with a CISCO ASA 5505 (eventually we'd like to implement VPN). When I connect the CISCO ASA, I get no internet passthrough at all.
Cisco WAN :: 2600 With IOS 12.3 / Basic Configuration To Allow Traffic Between Two LANs?
Dec 16, 2011I have a Cisco 2600 with IOS 12.3. I need a very basic configuration to allow traffic between two LANs. To test this I cleared the router config to the factory default state and configured my network addresses on the interfaces.
When I connected a PC to each interface I found they could ping each other, I was expecting to have to write ACLs to permit the traffic into the interfaces, thinking that the default behaviour of the router would be to deny access. default bahaviour without any ACLs or other routing configurations?
My config, such as it is, is as follows:
Current configuration : 770 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
Cisco WAN :: 1841 Basic ADSL Configuration Guide
Aug 5, 2012I am trying to configure a Cisco 1841 to allow the users to access the internet. This is my first step with ppp. All the rest of the configuration is ok but I don't know how to setup the interfaces Dialer0 and ATM0/0/0.
Need very basic configuration that I can analyze and use on my device?
Cisco Wireless :: 1941W Basic Configuration Required
Apr 22, 2012I am replacing a cisco linksys router with a 1941w.
I have the 0/0 accepting a DHCP from the ISP then I have 0/1 going to a switch and hosting a dhcp server.
Where I have an issue is:
A) Finding a way to turn on the wireless and make it use the same DHCP as wired and setting up a user name/wep password
B) Turning on the GUI that is supposed to be embedded on this.
C) Finding a way to make the DNS point to the default gateway so that I don't have to set the address everytime we move the box.
Here is my current configuration, and with it I can get onto the wired network and get to the internet.
Current configuration : 4712 bytes
!
! No configuration change since last restart
version 15.1
[Code]...
Cisco Switching/Routing :: 4900M - Basic Configuration And Administration
Jan 1, 2013First time user of cisco hardware and we just purchased the 4900m catalyst switch. My question is very general. I am simply hoping to network 3 servers together and I do not wish to do any fancy or advanced configuration. Can I simply use the web management interface for network administration and setup? I just downloaded the Catalyst 4500 Series Switch Cisco IOS software configuration guide and they talk about Cisco View network management system, is this my answer or is this what most people use for basic configuration and administration?
View 3 Replies View RelatedCisco VPN :: ASA 5505 - Basic Web Access
Nov 27, 2011I have a Cisco ASA5505 running the latest asdm and ios.
[I]Cisco Adaptive Security Appliance Software Version 8.4(2) Device Manager Version 6.4(5)206[/I]
I am trying to get basic web resolution and access but not having any luck. I just wanted to know if there is anything special that I needed to do with the ASA before I can do this. I've made a quick visio diagram of the network, see below: [URL]
The Vigor has a local sub net of 192.168.0.x/24 however there is also a "For routing use only" option. See below: {URL}. I'm hopeful that by configuring the "For routing use ip address" as one of my allocation of public ip's, that it should work okay. I can actually ping by IP and name from the interface of the ASA but can't do that or browse to websites from clients which have their default gateway set to 192.168.0.252. I was under the assumption web browsing should work out of the box almost as it's treated as an outgoing connection. Here is my config for you to look at: (note, I've tried to set the route outside to the local ip of the dray tek and also the "For routing usage only" IP address).
ASA Version 8.4(2)
hostname gilwoodasa
domain-name gilwood.local
enable password 9PvFytIZ2Vpy8Gon encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[Code]...
So, if you're still reading this - all I am after is a way to get basic web browsing working. Here are the logs which show the attempted web access. [URL]
Cisco Firewall :: Basic ASA 5520 To Allow Access From Internet
Jan 17, 2013I've got what is probably a very basic question - but i can't figure it out.I have: Internet (ADSL) -> 2851 (ADSL wic) -> 5520 -> internal LAN (192.168.1.x/24)
The asa has just replaced a Checkpoint firewall.I've set up the ASA to the point where all hosts on the internal LAN have internet access (using a dynamic PAT on that network). This all works well.
The problem i have is i am trying to allow access from the internet to an internal host on a specifc TCP port (as i had done on the Checkpoint) but i'm getting:
Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:111.111.111.11/52135 dst inside:192.168.1.252/5555 denied due to NAT reverse path failure
From what i have read i need to add a NAT exemption for this particular use case - to avoid the dynamic NAT i have setup, but im not sure how to do so.I'm running 9.1 on the ASA, no VPNs yet. Just this basic setup.
Cisco :: Configuration Of Management On LMS 4.0.1
Dec 6, 2011I'm using LMS 4.0.1 (current patches and device packages)
There is a problem with the configuration fetch.There are some 2503 routers with IOS 11.3(6) and the message on LMS is: Couldnot enter ENABLE Mode from USER Mode on Device
The devices arn't configured with username, only telnet pw and enable pw; no access-lists or other limitations configured
The credential check is ok ... multiple checks done ... devices deleted, new discovery ... devices deleted and manually added .... with the link //serverip:1741/rme/rmedevices.do I've changed the timeouts multiple times (up to 60 seconds for TFTP, SNMP) .... all these have had no effect of the config fetch
Cisco :: Configuration Management In LMS 4.1 Is Not Working?
Jan 9, 2013I need to archive the configuration for the devices but it states that SSH fails to authenticate although I have checked the credentials many times.
View 1 Replies View RelatedCisco Firewall :: ASA 5550 / Basic NAT From Outside Remote-access IPSec VPN To Inside?
Mar 16, 2012I cannot get this to work properly and I've even had a Cisco engineer from TAC set-this up... and it literally broke my inside network. I have a VPN range of addresses..x.x.x.x on the Outside that needs access to a server on the Inside at y.y.y.y. HTTPS/443 connectivity. I need to NAT my VPN subnet/pool in order to talk to the inside host, as that host will not accept traffic from my VPN subnet, but obviously, will accept traffic from Inside my private network.
The Cisco tech entered the following static NAT statement to "fix" the problem - nat (outside,inside) source static VPN Inside-Network destination static Host-y.y.y.y Host-y.y.y.y For whatever reason, whenever this is configured on my ASA 5550 v8.3(2)25 the Inside interface starts proxy arping and assigns all IP addresses on my private network with the MAC address of the Inside interface.
The y.y.y.y is on a remote, routed network within my private, corporate MPLS network. My Inside private network (Inside-network shown in the static NAT above) is x.x.x.x. Not sure why this happens, but it kills my entire network and I have to jump through hoops to quiesce the network and get everything back to normal.I've tried to Dynamic-PAT/hide the VPN range behind the Inside interface through ASDM and that seems to do nothing.The NAT statement above will break my network. How to NAT this connection without killing my Inside network? Or, on how to properly hide my VPN subnet/pool behind my Inside interface and back to the VPN subnet/pool.
Cisco WAN :: 6500 Management Ip Address Configuration?
Mar 2, 2013I would like to configure a Management ip address on 6500 by giving ip to the SVI. Following is the configuration done
1) int vlan X
ip address 10.1.1.1 255.255.255.0
no shut
However i am not able to reach this Switch IP from other subnet's. for ex:- 192.168.1.0/24.What next configuration should be done, in order to make this work. I dnt want to use any routing protocol.
Belkin Basic Router Is Connected To A Comcast Modem But No Internet Access?
Nov 27, 2011My neighbor is using my Belkin Router the basic one and has comcast. We both use his internet and have had no problems until the past 3 days. He just got the home phone service from comcast and the phone line is setup through the modem. Ever since comcast came to his apartment and set this up the home phone service to his modem the router is connected but there is no internet access. What is going on and how can I fix this. He has an HP with windows Vista and I have a Toshiba Satellite L675 that has Windows 7 Home premium edition on it.
View 1 Replies View RelatedCisco :: Ciscoworks 3.2 RME Compliance Management With 802.1x Port Configuration
Nov 6, 2011i am currently trying to use LMS 3.2 Compliance management to verify and alter our access port configurations for 802.1x. Below is our current configuration
View 1 Replies View RelatedCisco Switching/Routing :: 4900M Management Configuration Via Vrf
Mar 10, 2013I am just going to deploy some new 4900Ms for a customer. Want to know if configuring management for 4900 (everything like NTP, AAA, SNMP , DNS ) is doable through management interface in management VRF and there are no caveats to be aware of.
View 1 Replies View RelatedCisco Wireless :: AP54N - Management VLAN-ID Matter In Configuration?
Aug 16, 2012I am working to configure AP541n AP, is able to connect to the AP wired, assign AP static IP with proper subnet mask & default gateway, when it's done, everything looks perfectly, but since I changed the management VLAN ID from 1 to 2, I can't even connect to the AP wired from the PC, why does the change matter?
View 2 Replies View RelatedCisco Application :: ACE 4710 - Context Management / Backup Of Configuration?
Jun 25, 2012I am looking at management (backup of the configuration) of the ACE 4710 running A4.1, the management software is Cisco Cirrus. The question I have is around the management of the context's, I have a backup of the Admin but would like the user context's also, how this is completed.
View 3 Replies View RelatedCisco Switching/Routing :: 4900M Management Configuration Required
Dec 8, 2011I am just going to deploy some new 4900Ms for a customer. Want to know if configuring management for 4900 (everything like NTP, AAA, SNMP , DNS ) is doable through management interface in management VRF and there are no caveats to be aware of.
View 1 Replies View Related