Cisco :: Configuration Of Management On LMS 4.0.1

Dec 6, 2011

I'm using LMS 4.0.1 (current patches and device packages)
 
There is a problem with the configuration fetch.There are some 2503 routers with IOS 11.3(6) and the message on LMS is:  Couldnot enter ENABLE Mode from USER Mode on Device
 
The devices arn't configured with username, only telnet pw and enable pw; no access-lists or other limitations configured

The credential check is ok ... multiple checks done ... devices deleted, new discovery ... devices deleted and manually added .... with the link  //serverip:1741/rme/rmedevices.do I've changed the timeouts multiple times (up to 60 seconds for TFTP, SNMP) .... all these have had no effect of the config fetch

View 2 Replies


ADVERTISEMENT

Cisco :: Configuration Management In LMS 4.1 Is Not Working?

Jan 9, 2013

I need to archive the configuration for the devices but it states that SSH fails to authenticate although I have checked the credentials many times.

View 1 Replies View Related

Cisco WAN :: 6500 Management Ip Address Configuration?

Mar 2, 2013

I would like to configure a Management ip address on 6500 by giving ip to the SVI. Following is the configuration done
 
 1) int vlan X
    ip address 10.1.1.1 255.255.255.0
    no shut
 
However i am not able to reach this Switch IP from other subnet's. for ex:- 192.168.1.0/24.What next configuration should be done, in order to make this work. I dnt want to use any routing protocol.

View 4 Replies View Related

Cisco :: Basic Ace30 Configuration For Management Access

Dec 13, 2012

in lab trying to run a test upgrade of an Ace30,can seem to get it right ace30 is in slot 1 of the 6500, management vlan 10

View 4 Replies View Related

Cisco :: Ciscoworks 3.2 RME Compliance Management With 802.1x Port Configuration

Nov 6, 2011

i am currently trying to use LMS 3.2 Compliance management to verify and alter our access port configurations for 802.1x. Below is our current configuration

View 1 Replies View Related

Cisco Switching/Routing :: 4900M Management Configuration Via Vrf

Mar 10, 2013

I am just going to deploy some new 4900Ms for a customer. Want to know if configuring management for 4900 (everything like NTP, AAA, SNMP , DNS ) is doable through management interface in management VRF and there are no caveats to be aware of.

View 1 Replies View Related

Cisco Wireless :: AP54N - Management VLAN-ID Matter In Configuration?

Aug 16, 2012

I am working to configure AP541n AP,  is able to connect to the AP wired, assign AP static IP with proper subnet mask & default gateway, when it's done, everything looks perfectly, but since I changed the management VLAN ID from 1 to 2, I can't even connect to the AP wired from the PC, why does the change matter?

View 2 Replies View Related

Cisco Application :: ACE 4710 - Context Management / Backup Of Configuration?

Jun 25, 2012

I am looking at management (backup of the configuration) of the ACE 4710 running A4.1, the management software is Cisco Cirrus. The question I have is around the management of the context's, I have a backup of the Admin but would like the user context's also, how this is completed.              

View 3 Replies View Related

Cisco Switching/Routing :: 4900M Management Configuration Required

Dec 8, 2011

I am just going to deploy some new 4900Ms for a customer. Want to know if configuring management for 4900 (everything like NTP, AAA, SNMP , DNS ) is doable through management interface in management VRF and there are no caveats to be aware of.

View 1 Replies View Related

Cisco :: 5508 WLC Configuration / Can't Access GUI On Management Interfaces Ip Address

Aug 30, 2011

I've got a new 5508 wireless lan controller and can ping the ip address of the management interface, but can't access the GUI at the management interface's ip address.  I can access the GUI on the service-port interface.  No static routes in the controller; trunk appears to be set up correctly.

View 5 Replies View Related

Cisco Switching/Routing :: 6509 Convert CatOS Configuration To Native IOS Configuration

Jul 17, 2012

I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
 
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.

View 1 Replies View Related

D-Link DIR-655 :: Does Auto Configuration Overrides Manual Configuration

Dec 14, 2012

I have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem.  So, out with the paperclip to do the big reset, causing me to lose my configuration.  When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams.  Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP.  I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either.  I tried EVERYTHING.  Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move.  UPnP had always been checked off in the router.  So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?

View 2 Replies View Related

Cisco :: What Is VLAN Management

Apr 10, 2013

What is VLAN Management

View 4 Replies View Related

Cisco :: Using NAT For Remote Management?

Apr 20, 2012

I have multiple remote sites connected back into my infrastructure via satellite. I'm building a GRE tunnel accross this satellite infrustructure to my user's routers. I'm using EIGRP through these tunnels and everything is working great as far as connectivity to my users is concerned. However, with each of these packages, I would like to be able to remotely manage the satellite modem. My problem is that these modems all have the same web management IP address (192.168.1.1:80) and I can't change them. I thought to myself, "too easy, this sounds like an excellant case for NAT!" Either I'm tackling this thing all wrong or something because I can't seem to get it to work. Here is what I've so far (IPs modified and extra info cut[CODE]

View 3 Replies View Related

Cisco Routers :: Does 860 Have CLI Management

Jan 26, 2012

A small remote site is going to need a dedicated 10mb connection to our Main Campus. Probably an 10mb ELAN connection(not decided as of yet). The site will be small - no bigger than 2500 sq feet with small walls possibly. Only one VLAN will be needed and we won't need any voice applications or back-up WAN ports. The site will provide connectivity for approximately 15 people. I've been looking at the 800 series routers for a solution. Do you think the 860 with the built-in 802.11 AP will suffice? I have a couple of concerns:
 
 Does the 860 have CLI management?Will I be able to create a secure, encrypted tunnel between the 860 and a 2811 router on our Main Campus side? The 2811 has a 10mb ELAN secure tunnel on one interface already. I will purchase another interface card for this new, remote site VPN connection.Will the built-in AP give me coverage for the sq footage? I understand that there are extenuating circumstances to be concidered but, generally speaking?
 
From the video spec I viewed, the presenter said it had "basic security". What does that actually mean? This concerns me, as I want to built a secure WAN connection.Finally, does the 800 series fit this application or are there other Cisco products I should consider?

View 0 Replies View Related

Cisco :: LMS 4.0 Does Not Appear In Device Management

Dec 14, 2011

I have installed successfully installed and configured LMS 4.0 and every thing was okay until the customer decided to change the server IP address without notifying any one.
 
so i have returned the server to its original ip address since nothing worked after they changed the IP, but even after restoring the old IP address the device descovery is okay, but when i navigate to the devices management nothing appears in the all devices drop down menu and the remaining menues also.
 
i have tried to restart and to start a new device discovery also i have tried to run a data collection but nothing changed.
 
still stck on the devices are not appearing in the device management tab.

View 1 Replies View Related

Cisco :: AIR-AP1231G-A-K9 Management IP?

Nov 18, 2012

I have two dinasour APs that I need to fix. They are configured in bridge mode to bridge a few VLANs between two sites. Right now the management IP on BVI 3 interface doesn't work. Does it have to be on BVI1 for it to work? When I say "work" I mean I am able to ping it and use SNMP to monitor it.

View 1 Replies View Related

Cisco :: 876 Remote Management - Connecting To WAN IP?

Dec 5, 2011

Any possibility remotely manage cisco 876? Remotelly I mean by connecting to WAN IP (DSL interface) from outside. It could be via CCP, telnet or ssh doesn't matter.

View 4 Replies View Related

Cisco :: Separate Interface For Management On ASA

Nov 5, 2012

I'm trying to separate my management traffic from regular traffic by splitting the management and "outside" interface to separate vlans but I'm hitting a routing issue. Say I have have a management network of 192.168.1.0 255.255.255.0 running across vlan 1 and I want to use 192.168.2.0 255.255.255.0 running across vlan 2 for the outside interface to send all the other traffic excluding the management traffic across. Tag both vlans on the external interface, say Eth0/0 Default route of route outside 0.0.0.0 0.0.0.0 192.168.2.1, With this, you can not hit the management interface because there is no route defined for the 192.168.1.0 network. However of course if you try to set one, you'll get the "connected route exists" error. How can I set the default route or gateway of the 192.168.1.0 network on the ASA. Switches just don't complain like the ASA does.

View 8 Replies View Related

Cisco :: WS-C4948 Vlan1 Management From Outside?

Feb 3, 2013

I'm trying to get a catalyst going for remote management using cisco network assistant.I've basically, enabled telnet;

enable conf t line vty 0 15 password {password}
login
exit
gave it an IP;
int vlan1 ip address {IP} {Subnet}
no shutdown
exit

[code]...

and write mem to save it all. I can ping, telnet and access cisco network assistant from inside the network perfectly. But the problem I'm having is accessing it from outside, can't even ping the device. I can ssh to other servers behind the network just fine. There is no firewall in place at the moment, the provider's drop is plugged in gige port 1?

View 3 Replies View Related

Cisco :: Native And Management VLANs?

Jun 2, 2012

The management VLAN(the one I use to connect to the devices) and the native VLAN dont have to be the same VLAN ,right?They are independent and can be different. For instance I can use VLAN 5 for management and 10 as the native VLAN

View 8 Replies View Related

Cisco :: WLC 4404 Bandwidth Management?

Jan 19, 2011

I have a WLC 4404 installed and we would like to manage the bandwidth per SSID.
Today we have configured many SSID because our campus has a lot of wireless users and any SSID has only one class C subnet (/24).
 
We would like to configure each SSID with more subnets.   is this possible ?
 
Additionally we need to restrict the bandwidth per SSID.  is this possible ? We have some SSID for less important users and we would like to assign the bandwidth per SSID.

View 4 Replies View Related

Cisco :: 3750x Management LAN / IP Connectivity?

Feb 6, 2013

I have created a management vlan on my network of 2950 and 3750 switches.  One 3750 has a trunk to each of the 2950 switches which includes the management VLAN.  On that 3750 the vlan and line protocol are both up even though there is no specific port assigned to the vlan; I believe the trunk connections allow the vlan line protocol to come up.  On another 3750 stack I have my VLAN defined with no ports designated or trunks; the VLAN is up however the line protocol is down.

View 12 Replies View Related

Cisco :: AP802GN - Broken Web Management

Jan 30, 2013

I recently upgraded an  AP802GN-E-K9 to version 15.2(2)JB (ap802-k9w7-mx.152-2.JB), which broke the web interface. The http server is still running, however the web interface is not available. The following is displayed instead Navigating to /ap_home.shtml etc shows the correct pages. Extracting the "tar" file from the Cisco site and looking in the /html/level/15/ directory in both the tar and flash shows files missing that I'd expect to exist ( frameHome.html , navHome.html etc ).
 
Alas, I have no SmartNet on this device (embeded into my 887VA-W) as it's for home

View 2 Replies View Related

Cisco :: Does 877 Allow LAN Connect To Router For Management

Jun 8, 2012

i just purchased a cisco 877 on ebay, when i got the router,, i connect to the LAN port,, but didn't get any ip from the router,, then i tried to hard-reset the router by press and hold the reset button on the back for a long time, but nothting happen, not sure if it reseted to the factory setting or not..then i try to connect to lan port again, still not getting an ip,, okay, then i try to manually config the ip to 10.10.10.5(also tried 10.0.0.5, 192.168.0-1.5) and try to connect to the router,, but still no luck, try to ping the router, no luck too, i tred to contact the seller,, he just said, the router is working for sure.. i must need an aux cable to program the router, LAN interface can't program the router, he doesn't want to refund my money,, i don't think that is true... does cisco 877 allow LAN management on default settings??

View 1 Replies View Related

Cisco :: WLC 5500 Management And Monitoring?

May 11, 2011

we are looking forward to monitoring the cpu, environment variables and the memory of a wireless lan controller via snmp. but we are not able to find in the mibs the right oid to manage this.can the exact oid be given in order to monitor these three elements on a cisco WLC 5500 series.

View 1 Replies View Related

Cisco :: 2811 - WLC - Cannot Reach Management IP From LAN

Jul 4, 2012

I have a 2811 (running 12.4(15)XZ) with a WLCM (4.2.209.0).
 
I have reset the configurations on both. Set FE and WLCM IPs on the router and gave WLC Management and AP manager addresses. All + PC are on the same subnet. Router pings all addresses besides AP-manager(intended). WLC CLI cannot ping PC and PC cannot ping (nor http) to WLC. PC can however ping and telnet the router on both the FE and WLCM IPs.
 
I followed the guides on WLCM configuration, did I miss something?
 
How can I access the management IP and the web GUI?
 
2811 config:
 
Building configuration... 
 
Current configuration : 1292 bytes
!
version 12.4
service timestamps debug datetime msec

[Code].....

View 17 Replies View Related

Cisco :: 6509 Sup-2T Management Through CMP Interface

Dec 3, 2012

We acquired recentlty a new Cisco 6509 with Sup-2T supervisor card
 
My question is the following : we have a management subnet on a Copper-based switch; we manage all equipments through this network. I planned to configure the management interface on the 6509 to connect this switch & monitor the VSS through it However, since it is a CMP interface, most of the actions (SNMP, IOS upgrade.. won't be possible through this link)  Moreover, I don't think LMS would be able to get the configuration through it (except by configuring a script running "attach" command & show run
 
Is there something I miss or must I add another interface of the Catalyst to this network (the problem being that I have no copper line card)

View 2 Replies View Related

Cisco :: LMS 3.2 Archive Management Failing?

Sep 4, 2011

config collection is failing.in detail its partial success(config fetch is success but archieve is failed).

View 1 Replies View Related

Cisco WAN :: Bandwidth Management On 1841?

Nov 5, 2012

I am trying to restrict bandwidth for a particular LAN IP address on my network using policy maps but it does not seem to be working, My LAN IP address is 192.168.20.199 which i am trying to limit the bandwidth on.
  
Cisco_1841#sh policy-map interface fa0/0FastEthernet0/0
Service-policy input: Bandwidth_Allocation_In
Class-map: BWTest_In (match-all)      0 packets, 0 bytes      5 minute offered rate 0

[Code].....

View 3 Replies View Related

Cisco :: WS-500 One Management Tool For Network

Jul 14, 2011

I have recently installed several of the new WS-500 series switches into my networks and much to my surprise they are not supported by the CNA tool as the older 500 series were. I tried using the CCA tool, but my routers and legacy switches are not supported under it. One of the reasons I bought the Cisco switches in the first place is because I wanted to use one tool to manage all components in my network. I feel rather irked about what seems to be a purposeful hampering of functionality of the SMB line of equipment. Is there a management application that will allow me to manage all of my Cisco devices from the same console?

View 3 Replies View Related

Cisco :: Change Management IP Of AIR-CT5508

Sep 25, 2011

I want to change the management IP of our wireless controller, I have 5 LAP1142N connected to this controller.
 
I have a few questions before I will do this task.
 
1. If I change the management IP, will the controller need a reboot?

2. Will the AP's automatically sync with the new management IP?

3. Do I need additional configuration on the AP's?

4. What else do I need to consider.

View 9 Replies View Related

Cisco :: 2504 - Wi-Fi Management Across Different Subnets

Jul 29, 2012

Is it possible to use a 2504 wifi controller to manage compatible AP's across different subnets ?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved