Cisco :: Does 877 Allow LAN Connect To Router For Management
Jun 8, 2012
i just purchased a cisco 877 on ebay, when i got the router,, i connect to the LAN port,, but didn't get any ip from the router,, then i tried to hard-reset the router by press and hold the reset button on the back for a long time, but nothting happen, not sure if it reseted to the factory setting or not..then i try to connect to lan port again, still not getting an ip,, okay, then i try to manually config the ip to 10.10.10.5(also tried 10.0.0.5, 192.168.0-1.5) and try to connect to the router,, but still no luck, try to ping the router, no luck too, i tred to contact the seller,, he just said, the router is working for sure.. i must need an aux cable to program the router, LAN interface can't program the router, he doesn't want to refund my money,, i don't think that is true... does cisco 877 allow LAN management on default settings??
View 1 Replies
ADVERTISEMENT
Aug 29, 2012
I am trying to use GNS to simulate this, but a bit difficult to achieve this. May I know can the Cisco Router handle below requirement? Example Cisco 2811
1) Bandwidth management based on IP Address or Subnet? For example; allocate 1Mbps (CIR) and 10Mbps (BIR) to 172.16.1.10
2) Can the Cisco Router control the inbound and outbound bandwidth?
3) Can you share the sample config?
View 7 Replies
View Related
Dec 17, 2012
How do I access the router's web gui management? I already enabled the ip http server and ip https commands. I have a username and password configured
I open a browser session with the ip address:URL, But I do not get the management GUI. I haven't used the GUI in many years,
Cisco Systems
Accessing Cisco CISCO1921/K9 "my-router"
Show diagnostic log - display the diagnostic log.
Monitor the router - HTML access to the command line interface at level 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
Show tech-support - display information commonly needed by tech support.
Extended Ping - Send extended ping commands.
View 3 Replies
View Related
Jun 30, 2011
I'm have serveral issues with my router.First, using port 8090, I'm unagle to get remote management of the router.Port 8090 is forwarded to the router 192.168.1.10 I have other issues too, I think the router is blocking my FTP conenction to my NDAS drives.I wish the router would show the UPnP port that are autoamtically added t othe system.Port 80 works well going to my NDAS drives.Firewall, DoS Blocking WAN are all turned off.
View 4 Replies
View Related
Mar 30, 2012
I have a small issue with Remote Management on my E4200v2.I have enabled it , select https and set Allowed Remote IP Address to any on the default port ( 8080 ).After all of this, I cannot connect to my router from my office or any other place. I'm using DDNS and all its ok ( updated at time ). I've tried also connecting to my direct ip address ( dynamic ) but with no result.P.S. no incoming log from port 443 using https.
View 3 Replies
View Related
Sep 23, 2012
I plugged in a 2TB external USB drive and restarted the router. The Disk Management tab appears blank, doesn't give option to format.
View 4 Replies
View Related
Mar 2, 2013
I have an issue with new Win8 & IE10. When I try to access web management interface of my wrt160nl (Firmware Version: 1.00.01 B15) via HTTPS I'm receiving the foolowing message:"Continue to this website (not recommended)." If I click on it another error page appears:"Certification error: Navigation blocked. There is a problem with this website's security certificate"
At the same time I'm able to acccess the management interface via HTTPS, but from my laptop with Win7 & IE9. There if I click on the red Certificate Error > View certificate and the certificate information is:Issued by: Linksys Issued to: Linksys Valid from : 1.1.2009 to 1.1.2010
So I'd like to know if I could update the router certificate or what settings should I use in IE10 in order to access the web management interface via HTTPS?
View 9 Replies
View Related
Oct 3, 2012
I'm a bit new to Cisco and i find this AAA a bit confusing..I've turend on AAA by:aaa new-model
Can I use this "default" list for WebVPN ? And what would be a different if i create new "sslvpn" list..Also when I'll be creating user for VPN remote access.. that user will also exist in local database and have access to router via SSH?Because the research I've done it doesn't seem you can group users in different "aaa groups" e.g. user admin belongs under "admin" aaa group which can do ssh to router, users for VPN can only do remote VPN access and not SSH and login into router.i saw ASA has some attribute for users called remote-user
•admin, in which users are allowed access to the configuration mode. This option also allows a user to connect via remote access.
•nas-prompt, in which users are allowed access to the EXEC mode.
•remote-access, in which users are allowed access to the network.
But i can't find this option in IOS on my 1900 Series ISR router.
View 1 Replies
View Related
Aug 25, 2012
I want to be able to login to a router remotely and foward a port on the router. I thought i saw a spot for remote management but don't know how to use it. I have a dyn account and can create a dns for it.
i setup security dvrs on the internet so clients can see cameras from outside their homes. I would like to be able to login to a router if i need to foward a port or something similar.
View 1 Replies
View Related
Jun 24, 2012
I am using 3945E Router as Easy VPN Server, with 15.1 IOS. On router I have bunch on usernames for VPN authentication, I want to restrict Router management access for them(ssh,telnet, http and so on).
View 2 Replies
View Related
May 16, 2013
i have router 2911
pub ip: 121.97.65.61-74
interface gigabitethernet 0/1
ip address 121.97.65.61/28
[Code].....
and other ip will drop/kick/disconnected automatically
how to implement this on access list
View 6 Replies
View Related
Aug 5, 2012
I can not even get in to management mode. In next program that just keeps trying to auto repair the connection and never displays any radio button option the direction state like "advanced settings".At the very least your PDF should match your user friendly **bleep** ware!The instructions even refer to itself wrong! It states "for manual set up go use browser connection section" then in that section it describes an auto set up and instructs you to follow the set up steps on the CD.
View 7 Replies
View Related
Nov 20, 2011
My University has free Internet at student homes, but we need to login by PPTP to get an official, public IPv4 and be able to reach the outside world. The network people at the University says that when the PPTP is up, everything should be open (no firewall of any kind).
have my WRT160NL that gets a 10.10.73.0/23 address from DHCP on WAN port. Currently I have 10.10.74.21. My internal network uses 172.17.17.0/24.My PPTP-server is located at 10.192.1.1 and when I connect, I usually get an IP in the 158.37.73.0/24-range. Currently I have 158.37.73.28. I use DynDNS to make sure I always know the public IP by the host binders.dyndns.info ...
So, I have Remote management enabled with HTTP and HTTPS, any IP and default port 8080. But no response from the outside world seems to go through.If I turn of the "filter ICMP" but keep the SPI Firewall on, I get ping reply from external sources towards my router, but still no HTTP or HTTPS response.I also have a Torrent I try to port forward to to be active, this is 23277, and this is the only thing that keeps coming up in the incoming log on my router.
It's not possible to connect to the routers management over the PPTP-tunnel?And why can't I get the port forward to work .. Same reason? PPTP 158.37.73.28 -> 172.17.17.100 (LAN) won't work?
View 1 Replies
View Related
Jan 21, 2012
I just found a slightly unsettling bug in the E4200v2 (running the latest firmware 2.0.36 build 126507).Administration > Local Management Access > Access via Wireless ... set to DISABLED. HOWEVER, when I attempted to access the web interface on a handy iPAD I had absolutely no problem getting through to the web interface (after providing username and passsword).Limiting access to wired clients seems like a simple a prudent measure ... which is why this option is there for the paranoid among us.This seems like a black-and-white bug.
View 9 Replies
View Related
Aug 23, 2011
I cannot access the WRT610n setup/management pages wirelessly from my Macbook using safari. I can access the router via wireless from iPhone and PC and I can access it from the Macbook via ethernet cable.
When I try to access the router from the Macbook I just get "Contacting..." in the Safari status line and eventually it times out.
I can access the internet using Safari via WRT610n wireless. The only page I can't access is the router's management page.
View 7 Replies
View Related
Jul 19, 2012
I am using an E2500 as an access point, which is working fine. I have an Ethernet cable on one of the LAN ports of the E2500 connected to a LAN port on my gateway router. The LAN address of the E2500 is 192.168.7.3 and the LAN address of the gateway router is 192.168.7.1. Clients on the E2500 wireless network have no problems getting to the Internet through the gateway router. Clients on the E2500 wireless network can reach the E2500 local management port at 192.168.7.3 on port 80. On the gateway router I am forwarding WAN port 8083 to LAN address 192.168.7.3 at port 80. But I cannot access the E2500 local management interface via the gateway router. The E2500 should see the request as from 192.168.3.1 due to NAT in the gateway router, right? I can reach any of my actual access points this way, just not a router being used as an access point. Security/design limitation of the router?
View 2 Replies
View Related
May 6, 2012
How to get HTTPS to work for local or remote management? Selecting HTTPS for either local or remote doesn't enable HTTPS for me. It still use HTTP.
View 2 Replies
View Related
Feb 2, 2007
We have a RV042. remote management is set to DISABLE - but even after restarting the router i can access the interface remotely over the internet.even when i enable it and change the port to say 5555 i can connect to the web interface using either port 5555 but ALSO on port 80.what's wrong here?the only way to stop that was to create a rule that blocks port 80 on the WAN interface. (btw. could this rule affect LAN users when browsing the web?)
View 7 Replies
View Related
Apr 10, 2013
What is VLAN Management
View 4 Replies
View Related
Apr 20, 2012
I have multiple remote sites connected back into my infrastructure via satellite. I'm building a GRE tunnel accross this satellite infrustructure to my user's routers. I'm using EIGRP through these tunnels and everything is working great as far as connectivity to my users is concerned. However, with each of these packages, I would like to be able to remotely manage the satellite modem. My problem is that these modems all have the same web management IP address (192.168.1.1:80) and I can't change them. I thought to myself, "too easy, this sounds like an excellant case for NAT!" Either I'm tackling this thing all wrong or something because I can't seem to get it to work. Here is what I've so far (IPs modified and extra info cut[CODE]
View 3 Replies
View Related
Jan 26, 2012
A small remote site is going to need a dedicated 10mb connection to our Main Campus. Probably an 10mb ELAN connection(not decided as of yet). The site will be small - no bigger than 2500 sq feet with small walls possibly. Only one VLAN will be needed and we won't need any voice applications or back-up WAN ports. The site will provide connectivity for approximately 15 people. I've been looking at the 800 series routers for a solution. Do you think the 860 with the built-in 802.11 AP will suffice? I have a couple of concerns:
Does the 860 have CLI management?Will I be able to create a secure, encrypted tunnel between the 860 and a 2811 router on our Main Campus side? The 2811 has a 10mb ELAN secure tunnel on one interface already. I will purchase another interface card for this new, remote site VPN connection.Will the built-in AP give me coverage for the sq footage? I understand that there are extenuating circumstances to be concidered but, generally speaking?
From the video spec I viewed, the presenter said it had "basic security". What does that actually mean? This concerns me, as I want to built a secure WAN connection.Finally, does the 800 series fit this application or are there other Cisco products I should consider?
View 0 Replies
View Related
Dec 14, 2011
I have installed successfully installed and configured LMS 4.0 and every thing was okay until the customer decided to change the server IP address without notifying any one.
so i have returned the server to its original ip address since nothing worked after they changed the IP, but even after restoring the old IP address the device descovery is okay, but when i navigate to the devices management nothing appears in the all devices drop down menu and the remaining menues also.
i have tried to restart and to start a new device discovery also i have tried to run a data collection but nothing changed.
still stck on the devices are not appearing in the device management tab.
View 1 Replies
View Related
Nov 18, 2012
I have two dinasour APs that I need to fix. They are configured in bridge mode to bridge a few VLANs between two sites. Right now the management IP on BVI 3 interface doesn't work. Does it have to be on BVI1 for it to work? When I say "work" I mean I am able to ping it and use SNMP to monitor it.
View 1 Replies
View Related
Dec 6, 2011
I'm using LMS 4.0.1 (current patches and device packages)
There is a problem with the configuration fetch.There are some 2503 routers with IOS 11.3(6) and the message on LMS is: Couldnot enter ENABLE Mode from USER Mode on Device
The devices arn't configured with username, only telnet pw and enable pw; no access-lists or other limitations configured
The credential check is ok ... multiple checks done ... devices deleted, new discovery ... devices deleted and manually added .... with the link //serverip:1741/rme/rmedevices.do I've changed the timeouts multiple times (up to 60 seconds for TFTP, SNMP) .... all these have had no effect of the config fetch
View 2 Replies
View Related
Dec 5, 2011
Any possibility remotely manage cisco 876? Remotelly I mean by connecting to WAN IP (DSL interface) from outside. It could be via CCP, telnet or ssh doesn't matter.
View 4 Replies
View Related
Nov 5, 2012
I'm trying to separate my management traffic from regular traffic by splitting the management and "outside" interface to separate vlans but I'm hitting a routing issue. Say I have have a management network of 192.168.1.0 255.255.255.0 running across vlan 1 and I want to use 192.168.2.0 255.255.255.0 running across vlan 2 for the outside interface to send all the other traffic excluding the management traffic across. Tag both vlans on the external interface, say Eth0/0 Default route of route outside 0.0.0.0 0.0.0.0 192.168.2.1, With this, you can not hit the management interface because there is no route defined for the 192.168.1.0 network. However of course if you try to set one, you'll get the "connected route exists" error. How can I set the default route or gateway of the 192.168.1.0 network on the ASA. Switches just don't complain like the ASA does.
View 8 Replies
View Related
Feb 3, 2013
I'm trying to get a catalyst going for remote management using cisco network assistant.I've basically, enabled telnet;
enable conf t line vty 0 15 password {password}
login
exit
gave it an IP;
int vlan1 ip address {IP} {Subnet}
no shutdown
exit
[code]...
and write mem to save it all. I can ping, telnet and access cisco network assistant from inside the network perfectly. But the problem I'm having is accessing it from outside, can't even ping the device. I can ssh to other servers behind the network just fine. There is no firewall in place at the moment, the provider's drop is plugged in gige port 1?
View 3 Replies
View Related
Jun 2, 2012
The management VLAN(the one I use to connect to the devices) and the native VLAN dont have to be the same VLAN ,right?They are independent and can be different. For instance I can use VLAN 5 for management and 10 as the native VLAN
View 8 Replies
View Related
Jan 19, 2011
I have a WLC 4404 installed and we would like to manage the bandwidth per SSID.
Today we have configured many SSID because our campus has a lot of wireless users and any SSID has only one class C subnet (/24).
We would like to configure each SSID with more subnets. is this possible ?
Additionally we need to restrict the bandwidth per SSID. is this possible ? We have some SSID for less important users and we would like to assign the bandwidth per SSID.
View 4 Replies
View Related
Feb 6, 2013
I have created a management vlan on my network of 2950 and 3750 switches. One 3750 has a trunk to each of the 2950 switches which includes the management VLAN. On that 3750 the vlan and line protocol are both up even though there is no specific port assigned to the vlan; I believe the trunk connections allow the vlan line protocol to come up. On another 3750 stack I have my VLAN defined with no ports designated or trunks; the VLAN is up however the line protocol is down.
View 12 Replies
View Related
Jan 30, 2013
I recently upgraded an AP802GN-E-K9 to version 15.2(2)JB (ap802-k9w7-mx.152-2.JB), which broke the web interface. The http server is still running, however the web interface is not available. The following is displayed instead Navigating to /ap_home.shtml etc shows the correct pages. Extracting the "tar" file from the Cisco site and looking in the /html/level/15/ directory in both the tar and flash shows files missing that I'd expect to exist ( frameHome.html , navHome.html etc ).
Alas, I have no SmartNet on this device (embeded into my 887VA-W) as it's for home
View 2 Replies
View Related
Jan 9, 2013
I need to archive the configuration for the devices but it states that SSH fails to authenticate although I have checked the credentials many times.
View 1 Replies
View Related
May 11, 2011
we are looking forward to monitoring the cpu, environment variables and the memory of a wireless lan controller via snmp. but we are not able to find in the mibs the right oid to manage this.can the exact oid be given in order to monitor these three elements on a cisco WLC 5500 series.
View 1 Replies
View Related
