Cisco :: WLC 4404 Bandwidth Management?
Jan 19, 2011
I have a WLC 4404 installed and we would like to manage the bandwidth per SSID.
Today we have configured many SSID because our campus has a lot of wireless users and any SSID has only one class C subnet (/24).
We would like to configure each SSID with more subnets. is this possible ?
Additionally we need to restrict the bandwidth per SSID. is this possible ? We have some SSID for less important users and we would like to assign the bandwidth per SSID.
View 4 Replies
ADVERTISEMENT
Nov 5, 2012
I am trying to restrict bandwidth for a particular LAN IP address on my network using policy maps but it does not seem to be working, My LAN IP address is 192.168.20.199 which i am trying to limit the bandwidth on.
Cisco_1841#sh policy-map interface fa0/0FastEthernet0/0
Service-policy input: Bandwidth_Allocation_In
Class-map: BWTest_In (match-all) 0 packets, 0 bytes 5 minute offered rate 0
[Code].....
View 3 Replies
View Related
Aug 29, 2012
I am trying to use GNS to simulate this, but a bit difficult to achieve this. May I know can the Cisco Router handle below requirement? Example Cisco 2811
1) Bandwidth management based on IP Address or Subnet? For example; allocate 1Mbps (CIR) and 10Mbps (BIR) to 172.16.1.10
2) Can the Cisco Router control the inbound and outbound bandwidth?
3) Can you share the sample config?
View 7 Replies
View Related
Aug 16, 2012
I setup a WLC5508 with 2 SSIDs, one for guest traffic and another for internal users. They are in separate subnets and are routed out to the internet via 2 different isps, with the guest network going over a bonded t1 and the internal users going out the primary internet connection for the company. While this works as desired and we've verified that while on the guest network we're going out the right isp, we've encountered an issue with saturation of the bonded t1 pipe by guests. We'd like to find a way to limit a guest to a capped down/up stream if possible, with downstream being the most important. The infrastructure includes 3560 switches and AIR-CAP3502I-A-K9 access points.
View 1 Replies
View Related
Sep 30, 2012
I have 20 mbps internet link and I have ASA 5505 . I have to divide this bandwidth 10-10 mbps each for Voice and Data . So that both can work properly. because when I am using it for both on same interface, I am getting Voice disturbance..
View 1 Replies
View Related
Jul 24, 2012
i have 16MB internet speed, i want to give inside interface in my ASA only 2MB to use how can i assign it ?
ASA Version 8.2(5) !hostname ConcordeASAenable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface
[Code].....
View 2 Replies
View Related
Aug 13, 2010
setting up Rate Control in Bandwidth Management. It doesn't seem to work at all. I knew from some other Posts that I need to have IPS on and I do.. Is there something else I need to do.
My users are connected wirelessly to the router through three different SSIDs and I have 3 VLANS. I need to set some limitations on two of the LANS.
View 1 Replies
View Related
Dec 20, 2011
We are looking at putting in a solution at a hotel for Free Guest WiFI.The solution would cover 4 floors and about 120 rooms and some open areas .In short the hardware would look as follows
-2500 controller
-1142LAP
-2960 PoE switch
-878 Adsl router for internet connectivity (20Mbps/1Mbps internet ADSL feed)
One of the concerns raised by the client is that they would like to make sure that no single user could eat up too much bandwidth creating problems for the rest of the users . Can the above KIT or something similar achieve this objective? As far as I can think of we would require a Proxy server .
View 6 Replies
View Related
Oct 12, 2011
I have a RVS4000 hardware v2 with firmware 2.0.2.7. I have a DSL modem in bridge mode and have the router set to PPPoE. Everything works fine except I want to use QOS which doesn't work fine. I have some vonage boxes set up on a switch set to port 1 trust mode is set to port and level 4 for highest priority. Port 2 I have on another switch set to priority 3. I tried turning bandwidth mangement on which doesn't seem to work at all so I don't even know if they QOS is even working. I set the max down stream and upstream provided after running a number of speed tests and setting it a little lower than my worst speed results. Once I did that I set up a rule for all traffic for rate control and set them just below the min and max I put in for isp bandwidth. I set the ip range from 192.168.1.100-190 this will cover anything that dhcp hands out and I also have a few statics set up on 192.168.1.180 and 181. However after enabling it I ran some speed tests and I still get full speed and the rules seem to be getting ignored.
View 2 Replies
View Related
Jun 1, 2011
I am trying to get ride of an old traffic management appliance and would like to replace it by a simple Cisco 3845.
The configuration is really simple:
Customers -- Router 3845 -- Internet
I want to be able to provide bundles to customer such 64kps garanteed/ 2mbps MIR (retail) and 2mbps garanteed no MIR (business).
I need also to specify to the router the total internet bandwitdh available (example: 20mbps symetrical).
This configuration will work ? Should I worry about any performance issue if I start to have a lot of customers ?
ip access-list extended Cust1
permit ip any sub_Cust1
permit ip subCust1 any
View 2 Replies
View Related
Jul 27, 2011
We have a Service Policy rule setup on our 5510 for SMTP traffic.
Problem is, this week someone sent a larger email 20+mb to dozens of recipeints and the outside interface was hitting 10mb, which is not what I would have expected with this rule in place, so I'm questioning the configuration. We know it was email because I disabled the server that receices our outbound mail to apply a signature and the traffic dropped immediately.
View 2 Replies
View Related
Oct 20, 2012
i have a small network with Polycom phones connected to the sf300 switch and have the pc's daisy chained via the second switch port on each phone. i have the pc traffic running on the default vlan 1 and the voice traffic running on the voice vlan 100. can i do bandwidth management on a vlan/port basis or is that not necessary. i want to ensure that the voice traffic is never impacted by the pc traffic on the same cable.
View 2 Replies
View Related
Sep 13, 2012
I have some clarifications regarding ASA firewall, it can be support bandwidth management and content security at the same time. we are looking for below features in ASA5510.
IP/Policy based bandwidth management.Controll the bandwidth and allocate the bandwidth to specified users or servers.Content Security. If not, which device I need to set for Internet Bandwidth Management and content security.
View 3 Replies
View Related
May 22, 2013
We have an ASA 5525 running version 8.6(1)2 and a 10 MG pipe. I have execs that want to limit bandwidth on users for stuff like youtube, stream media, and downloads. I found the article on ‘Bandwidth Management(Rate Limit) Using QoS Policies’ so it appears our firewall can do what we want. I’m not a cisco person. My knowledge is limited when it comes to configuration – that’s why we have SmartNet.
Can bandwidth be limited on end users and/or can they limit the ‘bandwidth rate limit’ to just youtube, steaming media, and downloads? If so, what should the limit be? and I’m assume this would be for ‘incoming’ traffic only? we’re running into some bandwidth hogs – usually youtube and/or streaming media. We have a Barracuda web filter which we’ve used to block and monitor activity but I simply do not have time to babysit this all day. I should also mention we do have critical data running up and down the pipe; such as credit card processing, DB replication between in house DB and hosted website, TPCx and EDI, FTP, and such that we don’t want restricted.
View 7 Replies
View Related
Sep 9, 2011
We have 1 mpbs bandwidth line, but most of the time we are getting only 300-500 kpbs download speed, i want to send statistics report to our ISP, what will be best procedure to test the bandwidth report, i have checked in some websites like bandwidthplace and speedtest but these sites are not accurate, how to check the actual bandwidth we getting from ISP against 1 Mbps. We have solarwinds monitoring tool in this i have configured the WAN interface for 1 mbps
View 5 Replies
View Related
Mar 9, 2012
I need to upgrade our Wireless Lan Controller to support new APs. I was able to get the new code due to a security advisory on the code we are running now. I am upgrading from 6.0.196.0 to 7.0.220.0 (MD). I have read in some of the technical docs that the WCS has to match the WLC. I cannot find any documentation as to what this entails on the WCS.
WCS version is 6.0.132.0 running on Windows.
View 7 Replies
View Related
May 23, 2011
We have two 4404's and WCS. The 4404's are almost maxed out. We have an addition 4404 which we would like to add to the group of 4404's
View 1 Replies
View Related
Oct 9, 2012
I have a Cisco WLC 4404 with version software 7.0.230.0 and it gived me a this logg
Oct 9 15:43:08 192.168.122.34 WLC_4404_CC: *osapiReaper:
Oct 09 15:41:49.549: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/895/stat.(erno 24)
View 3 Replies
View Related
Dec 19, 2012
I have a Cisco 4404 WLC that is up, has green status light, the interfaces are showing activity. I see it connected to my Cisco 6500, (Sh port status) it shows connected and trunking,; I also see a lot of activity on the interfaces. Also it will not let me console in, I can console in on my other Cisco 4404 WLC's with out and issues, so I know my cables and configure are correct. The only change a I made today was the time zone. I noticed the time was off by a hour and noticed that the time zone wasn't set so I set it correctly. Shortly after that I saw the WLC go belly o up in my WCS. I tried rebooting the WLC several times without luck. Since I can not gain access via the console I can not really trouble shoot.
View 10 Replies
View Related
Jun 9, 2011
Trying to upgrade my Wireless LAN controller model 4404, I'm running 4.1.190.4 code and want to upgrade to 6.0.202. Looking at the release notes for 6.0.202 and the compatibility matrix, the matrix indicates I two intermediate loads first. One is 4.1.192.35m and the other is 6.0.182.0 then I can load 6.0.202 code. My problem is I can't find the 4.1.92.35m code. Looking at the software download the highest 4.1 folder has is 4.1.185.0. where to find the 4.1.192.35m code for 4404 WLC?
View 1 Replies
View Related
Aug 24, 2011
we have cisco wlc 4404. and we want to access it thru internet.
i have attached the management interface screenshot.
View 6 Replies
View Related
May 30, 2012
WLC 4404 is configured as Anchor controller, the MAC violation are captured by Controller. the Violated MAC are deleted manually through GUI, but when tried deleting through CLI using command
>Config exclusionlist delete <mac address>
we get error message as error deleting user <mac address>
View 6 Replies
View Related
Apr 17, 2011
We have 2 4404 controllers running 6.0.x code. I have several SSID setup with different VLANS. When the clients associate they do not show the name of the AP they are connected to, is there any way to display the assocated AP name?
View 2 Replies
View Related
Sep 17, 2008
I got a WLC4404 running software version 5.1.151.0 with 40 LWAPPs (mostly 1242AG). We got new Dell Latitude E6500 Laptops with Intel 5100 NICs. After upgrading the bios to the latest version and installing the latest wlan driver, wireless is working the most time.After about 4 reboots I see the following message in the WLCs logfile: "Thu Sep 18 13:53:10 2008 AAA Authentication Failure for UserName:host/hostname.domain.name User Type: WLAN USER".After I disable the wlan-card, it's working again.
View 7 Replies
View Related
Apr 24, 2011
I am facing a strange problem in my WLAN Setup. none of my wireless clients are able to associate with Wireless LAN but when I delete and create a new wireless profile in WLC 4404 clients starts associating with WLAN. every 2-3 days I had to delete and create wlan profile. Is it related to IOS bug or any other problem? My Wireless LAN Controller image is AIR-WLC4400-K9-5-1-151-0.aes.
View 4 Replies
View Related
Jun 29, 2012
Upgraded our WLC 4404 from 6 to 7 so we could upgrade some WAPs to 3500i. After upgrading all 8- 1120 and 1240s connectivity were lost.
We reverted back to OS 6 and all came back to Controller
WLC Software version = 6.0.199.4
WLC Emergnecy Image Version = 7.0.235
[Code].....
Our vendor states this should be a compatible mix and they are also checking as to why it is not working as planned.
View 1 Replies
View Related
Mar 22, 2009
I have a 4404 with 3 SSID's configured on it. I only want all SSID's to be available on one floor in one building and not on any other AP's in any other building or floor.I thought the way to do it was via AP group but have not had any luck getting that to work. I setup a group for the AP's that I do not want all SSID's and then assigned those AP's to that group. However, I can still see all three SSID's where I only want to see 2 SSID's.
View 4 Replies
View Related
Feb 27, 2013
I've downloaded Prime Infrastructure 1.2 eval and wanted to see what it looked from WCS that I am currently using to manage the wireless network and I added the WLC (4404) device but it list the device as "Managed with Warning" and I can't find what the warning is.
View 3 Replies
View Related
Feb 13, 2012
I have WLC 4404 Controller with 180 LWAPP. i want to disable Broadcast SSID from some specified APs not all. is it possible to do that with 4404 WLC controller.
View 9 Replies
View Related
Sep 9, 2012
I have Cisco 4404 WLC with Image 7.0.235.0 We have one SSID Sup_Admin with following config. Which is getting the IP address from the interface pool “corp”.
WPA+WPA2 with AES and TKIP
Auth key Mgmt is 802.1X
We are using Cisco ACS as radius server On the same WLC I have created another SSID Corp_Admin . Which also should get the IP address from the interface pool “corp”. Both SSID has the same settings ,but the second SSID is not working.
View 12 Replies
View Related
Mar 20, 2012
The story is that we recently upgraded our 4404 controller to the new 7.2.0.230 code. This upgrade was from 4.2.209 code. I would like to make the change to the Multicast setup so that It is multcasted and not unicasted.So I went into the controller and selected MULTICAST for AP multicast mode and entered in a multicast ip of 239.255.1.60 ( default choosen in the cisco howto's)I then test the reason for enabling the multicast and it doesnt work. The problem is that the Wireless HP printers setup to use Apples IPRINT are not able to be found. However, when I select the Multicast setting for the APs to be UNICAST the Ipads can find the Printers and print to them.What am I doing wrong with this Multicast setting? Do i need to add a Multicast address to the router?
View 2 Replies
View Related
Nov 27, 2011
I have a 4404 running firmware 7.0 and something happened (don't think it was a hack), but all of a sudden I can't login to the box via web or ssh or even telnet.
In trying the recovery procedure, I get a lot of messages scrolling through and cannot do the Restore-Password command on the CLI.
I'm attaching the whole capture, but here's a truncated capture from the procedure:
*fp_main_task: Nov 21 10:39:46.501: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*fp_main_task: Nov 21 10:39:46.501: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
[Code].....
So as you can see, my prompt to enter the command is taken up by this fp_main message and it uses up the first and only time I can enter this in. I'm trying everything I can to not have to go back to factory defaults.
View 24 Replies
View Related
Mar 8, 2011
I have (2) WLC-4404's with one in standby. I noticed this controller has been up for 300+ days and i was just wondering if it will be useful to reboot these once in a while? Any benefits or should i just leave them running?
View 4 Replies
View Related
