Cisco :: 2960 Bandwidth Management For Wireless Clients
Dec 20, 2011
We are looking at putting in a solution at a hotel for Free Guest WiFI.The solution would cover 4 floors and about 120 rooms and some open areas .In short the hardware would look as follows
-2500 controller
-1142LAP
-2960 PoE switch
-878 Adsl router for internet connectivity (20Mbps/1Mbps internet ADSL feed)
One of the concerns raised by the client is that they would like to make sure that no single user could eat up too much bandwidth creating problems for the rest of the users . Can the above KIT or something similar achieve this objective? As far as I can think of we would require a Proxy server .
View 6 Replies
ADVERTISEMENT
Aug 16, 2012
I setup a WLC5508 with 2 SSIDs, one for guest traffic and another for internal users. They are in separate subnets and are routed out to the internet via 2 different isps, with the guest network going over a bonded t1 and the internal users going out the primary internet connection for the company. While this works as desired and we've verified that while on the guest network we're going out the right isp, we've encountered an issue with saturation of the bonded t1 pipe by guests. We'd like to find a way to limit a guest to a capped down/up stream if possible, with downstream being the most important. The infrastructure includes 3560 switches and AIR-CAP3502I-A-K9 access points.
View 1 Replies
View Related
Jan 19, 2011
I have a WLC 4404 installed and we would like to manage the bandwidth per SSID.
Today we have configured many SSID because our campus has a lot of wireless users and any SSID has only one class C subnet (/24).
We would like to configure each SSID with more subnets. is this possible ?
Additionally we need to restrict the bandwidth per SSID. is this possible ? We have some SSID for less important users and we would like to assign the bandwidth per SSID.
View 4 Replies
View Related
Nov 5, 2012
I am trying to restrict bandwidth for a particular LAN IP address on my network using policy maps but it does not seem to be working, My LAN IP address is 192.168.20.199 which i am trying to limit the bandwidth on.
Cisco_1841#sh policy-map interface fa0/0FastEthernet0/0
Service-policy input: Bandwidth_Allocation_In
Class-map: BWTest_In (match-all) 0 packets, 0 bytes 5 minute offered rate 0
[Code].....
View 3 Replies
View Related
Aug 29, 2012
I am trying to use GNS to simulate this, but a bit difficult to achieve this. May I know can the Cisco Router handle below requirement? Example Cisco 2811
1) Bandwidth management based on IP Address or Subnet? For example; allocate 1Mbps (CIR) and 10Mbps (BIR) to 172.16.1.10
2) Can the Cisco Router control the inbound and outbound bandwidth?
3) Can you share the sample config?
View 7 Replies
View Related
Sep 30, 2012
I have 20 mbps internet link and I have ASA 5505 . I have to divide this bandwidth 10-10 mbps each for Voice and Data . So that both can work properly. because when I am using it for both on same interface, I am getting Voice disturbance..
View 1 Replies
View Related
Jul 24, 2012
i have 16MB internet speed, i want to give inside interface in my ASA only 2MB to use how can i assign it ?
ASA Version 8.2(5) !hostname ConcordeASAenable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface
[Code].....
View 2 Replies
View Related
Aug 13, 2010
setting up Rate Control in Bandwidth Management. It doesn't seem to work at all. I knew from some other Posts that I need to have IPS on and I do.. Is there something else I need to do.
My users are connected wirelessly to the router through three different SSIDs and I have 3 VLANS. I need to set some limitations on two of the LANS.
View 1 Replies
View Related
Oct 12, 2011
I have a RVS4000 hardware v2 with firmware 2.0.2.7. I have a DSL modem in bridge mode and have the router set to PPPoE. Everything works fine except I want to use QOS which doesn't work fine. I have some vonage boxes set up on a switch set to port 1 trust mode is set to port and level 4 for highest priority. Port 2 I have on another switch set to priority 3. I tried turning bandwidth mangement on which doesn't seem to work at all so I don't even know if they QOS is even working. I set the max down stream and upstream provided after running a number of speed tests and setting it a little lower than my worst speed results. Once I did that I set up a rule for all traffic for rate control and set them just below the min and max I put in for isp bandwidth. I set the ip range from 192.168.1.100-190 this will cover anything that dhcp hands out and I also have a few statics set up on 192.168.1.180 and 181. However after enabling it I ran some speed tests and I still get full speed and the rules seem to be getting ignored.
View 2 Replies
View Related
Jun 1, 2011
I am trying to get ride of an old traffic management appliance and would like to replace it by a simple Cisco 3845.
The configuration is really simple:
Customers -- Router 3845 -- Internet
I want to be able to provide bundles to customer such 64kps garanteed/ 2mbps MIR (retail) and 2mbps garanteed no MIR (business).
I need also to specify to the router the total internet bandwitdh available (example: 20mbps symetrical).
This configuration will work ? Should I worry about any performance issue if I start to have a lot of customers ?
ip access-list extended Cust1
permit ip any sub_Cust1
permit ip subCust1 any
View 2 Replies
View Related
Jul 27, 2011
We have a Service Policy rule setup on our 5510 for SMTP traffic.
Problem is, this week someone sent a larger email 20+mb to dozens of recipeints and the outside interface was hitting 10mb, which is not what I would have expected with this rule in place, so I'm questioning the configuration. We know it was email because I disabled the server that receices our outbound mail to apply a signature and the traffic dropped immediately.
View 2 Replies
View Related
Oct 20, 2012
i have a small network with Polycom phones connected to the sf300 switch and have the pc's daisy chained via the second switch port on each phone. i have the pc traffic running on the default vlan 1 and the voice traffic running on the voice vlan 100. can i do bandwidth management on a vlan/port basis or is that not necessary. i want to ensure that the voice traffic is never impacted by the pc traffic on the same cable.
View 2 Replies
View Related
Sep 13, 2012
I have some clarifications regarding ASA firewall, it can be support bandwidth management and content security at the same time. we are looking for below features in ASA5510.
IP/Policy based bandwidth management.Controll the bandwidth and allocate the bandwidth to specified users or servers.Content Security. If not, which device I need to set for Internet Bandwidth Management and content security.
View 3 Replies
View Related
May 22, 2013
We have an ASA 5525 running version 8.6(1)2 and a 10 MG pipe. I have execs that want to limit bandwidth on users for stuff like youtube, stream media, and downloads. I found the article on ‘Bandwidth Management(Rate Limit) Using QoS Policies’ so it appears our firewall can do what we want. I’m not a cisco person. My knowledge is limited when it comes to configuration – that’s why we have SmartNet.
Can bandwidth be limited on end users and/or can they limit the ‘bandwidth rate limit’ to just youtube, steaming media, and downloads? If so, what should the limit be? and I’m assume this would be for ‘incoming’ traffic only? we’re running into some bandwidth hogs – usually youtube and/or streaming media. We have a Barracuda web filter which we’ve used to block and monitor activity but I simply do not have time to babysit this all day. I should also mention we do have critical data running up and down the pipe; such as credit card processing, DB replication between in house DB and hosted website, TPCx and EDI, FTP, and such that we don’t want restricted.
View 7 Replies
View Related
Aug 2, 2012
Apparently on older switches you could just enter the "management" command under the new VLAN interface and it would pull the config from the old one, apparently that feature isn't around anymore. I've tried establishing a trunk to the damned thing and trying to switch over that way, but it doesn't seem to work.
View 4 Replies
View Related
Jun 19, 2012
we want to dedicate 2mb to one of our fa ports on our 2960, is this easily done, or can be done on a 2960?
View 4 Replies
View Related
Sep 11, 2012
We have a 2960 switch (switch2), whose Management IP cannot be reached/Ping'd. Could not Ping . We have checked the following, but still no clue on the root cause. Haven't tried a reboot yet.
Topology.
All switches are cascaded through trunk and allows all v lan's.
L3switch1 <-> switch1 <-> switch2 <-> switch3 <-> L3switch2
Switch 2 has correct ARP entries for the other switches that we try to ping.Mac address table is fine.Switches other than Switch 2 has proper ARP and Mac entries.This Mgmt v lan is not pruned across any trunks. (we are able to ping switch3 crossing switch2 when tried from switch1)Switches are running PVST and convergence is fine.No access list to deny the traffic.Tried sut/no shut on the V lan interface.
But still switch 2 could not be reached.
View 4 Replies
View Related
Jun 7, 2011
We have quite a few 3560 & 2960 on our edge network - what I have been looking at was to access switches via web-interface i.e. web-browser. Only problem with this is it always gives you access on privilige level 15 which is not ideal as not all who we decide to give access to these switches will be admin and allowed to configure these swicthes - In the 3560/2960 data-sheet states:
"Alternatively, a local username and password database can be configured on the switch itself. Fifteen levels of authorization on the switch console and two levels on the Web-based management interface provide the ability to give different levels of configuration capabilities to different administrators"
Where as there is no mention of how to configure these two levels of Web-based management in the configuration guide.
View 8 Replies
View Related
Oct 23, 2007
I'm working with two Catalyst 2960 switches and I would like to know if there is a way to monitor bandwidth on individual ports. Ideally I would like to have one graph showing a bandwidth usage reading on each port. I tried using the Network Assistant to accomplish this, but I was only able to view one port at a time. I also tried using a traffic graphing program from Paessler, but a MIB file is needed to allow the program to connect to the switch. When I ran a search on the network management page the 2960 was not on the list for MIB supported products. Is this type of graph possible to do?
View 2 Replies
View Related
Jun 11, 2013
Any example to limit the bandwidth using the MAC address on 2960 ? I want to limit the bandwidth (IN / OUT) of a server only for Internet flows.
View 2 Replies
View Related
Feb 9, 2012
I have ciscl catlyst 2960 8port switch, (flash:c2960-lanbasek9-mz.122-50.SE4/c2960-lanbasek9-mz.122-50.SE4.bin).
and in need to configure bandwidth limit for one of the port as a 1Mbps.
View 5 Replies
View Related
Apr 2, 2013
I am trying to get to work Web-based authentication on Catalyst 2960 and 3560 for clients that don't support dot1x. I followed this guide. Here's the problem: Client (win7) joins the network, opens the web browser and tries to navigate to any http site. The switch forces him the "login" page in which he has to enter credentials. After the client enters credentials, the switch sends http 500 internal server error page and nothing happens. Doesn't matter if the credentials were correct or not. Also i checked radius logs for requests, the switch doesn't even ask radius.
The configuration:
sh ip admission configuration
Authentication Proxy Banner not configured
Consent Banner is not configured
[Code].....
View 6 Replies
View Related
Jul 7, 2011
On my country, international bandwidth still expensive. I want to split local and international bandwidth and limit inbound and outbound bandwidth for each ip like this:
IP 10.100.10.11 can use 100Mbps local bandwidth, 1Mbps international bandwidth
IP 10.100.10.12 can use 100Mbps local bandwidth, 2Mbps international bandwidth
I want to use
Router 3825Switch 2960
NB: I have online one internet line.
Was the above equipment can perform functions that I want or need any additional equipment? And Should i use 2 line to achieve my goal?
View 1 Replies
View Related
Sep 18, 2012
I want to configure switch port bandwidth limit for my Catalyst 2960-48, is there any hardware / ios limitation? can I configure it at all 48 switch ports?
View 1 Replies
View Related
Apr 4, 2012
how can i limit bandwidth on a gig port of 2960 or 4506e switch?
View 9 Replies
View Related
Aug 22, 2011
We are about to share a 10 MBit ISP connection with 2 others companies, and they are going to split the bill up into 3,3 and 4 Mbit, so we where thinking that we could setup a switch before their and ours router and provide them with a static IP from our ISP. But is it possible to set a bandwidth limit on the ports of a Cisco Catalyst 2960-8TC, so that we can set a limit of 3,3 and 4 on 3 ports.
View 1 Replies
View Related
Feb 1, 2011
I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies
View Related
Jun 18, 2012
I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
Result of the command: "show running-config"
: Saved
:
ASA Version 7.2(4)
!
hostname ASA
domain-name default.domain.invalid
[code].....
what I need to add to get the vpn client to be able to ping the router and clients?
View 3 Replies
View Related
Nov 5, 2012
We currently have an ASA 5520 communicating with 10 ASA 5510's, all on static outside addresses. I was asked to add 5 additional 5510's on dynamic address. All worked well in testing until it was decided that some of the dynamic clients needed to talk to each other.
My testing shows packets just dying in the 5520.
View 1 Replies
View Related
Jul 6, 2012
I have a Netgear WNDR4500 running the stock firmware, acting as a router for my home. I also have 2 routers that are flashed with DD-WRT (Linksys WRT54G and Asus WL-520GU) running as client bridges. The Netgear is 192.168.1.1 and the other 2 client bridges are 192.168.1.2 and 192.168.10.3. The Netgear router is performing DHCP giving addresses from 192.168.10.100 to 192.168.10.254. I have numerous machines connected to the Netgear, wirelessly and wired, and numerous machines wired to each client bridge. All machines have IP addresses that are 192.168.10.100, 192.168.10.101, 192.168.10.102, etc... Everything is working fine, but I have one question: When I access the Netgear router, it shows the client bridges as clients, machines that are wired and wireless to the Netgear router are listed as clients, but the client list does not show any clients that are connected to the client bridges. I assumed that since the router is performing DHCP that all clients would show up.
View 2 Replies
View Related
Sep 9, 2011
We have 1 mpbs bandwidth line, but most of the time we are getting only 300-500 kpbs download speed, i want to send statistics report to our ISP, what will be best procedure to test the bandwidth report, i have checked in some websites like bandwidthplace and speedtest but these sites are not accurate, how to check the actual bandwidth we getting from ISP against 1 Mbps. We have solarwinds monitoring tool in this i have configured the WAN interface for 1 mbps
View 5 Replies
View Related
Feb 7, 2012
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies
View Related
Feb 11, 2013
I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies
View Related
