I am trying to use GNS to simulate this, but a bit difficult to achieve this. May I know can the Cisco Router handle below requirement? Example Cisco 2811
1) Bandwidth management based on IP Address or Subnet? For example; allocate 1Mbps (CIR) and 10Mbps (BIR) to 172.16.1.10
2) Can the Cisco Router control the inbound and outbound bandwidth?
3) Can you share the sample config?
I got connected ASA ----- ROUTER 2811) to metroethernet switch from my ISP , with a 4MB of bandwidth but the internet connections to all my LAN has been frozen and we lost connection to the internet, to restart the internet service I need to boot the ROUTER 2811 - and ISP switch to rollback the internet operation,My ISP support tell me if is possible to set up the traffic bandwidth in one or both borders devices, ( ASA 5510 or ROUTER 2811)
View 3 Replies View RelatedI have a cisco Swtich SGH 300-20 Gigabit switch i configure 2 vlan one is default and one is vlan 10
Vlan 1 ip range 172.16.0.0/23
Vlan 10 ip range 172.16.2.0/24
Client on Vlan getting Proper IP from DHCP Server all i need is to distribute internet bandwidth we have 6/3 mb and i want to give 4/2 mb to vlan 1 and 2/1 mb to Vlan 10
Int Gi16 on switch is configured as trunk port and is connected to cisco 2811 router
what are the command used to distribute bandwidth between these 2 vlans
I have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
I have a 2811 (running 12.4(15)XZ) with a WLCM (4.2.209.0).
I have reset the configurations on both. Set FE and WLCM IPs on the router and gave WLC Management and AP manager addresses. All + PC are on the same subnet. Router pings all addresses besides AP-manager(intended). WLC CLI cannot ping PC and PC cannot ping (nor http) to WLC. PC can however ping and telnet the router on both the FE and WLCM IPs.
I followed the guides on WLCM configuration, did I miss something?
How can I access the management IP and the web GUI?
2811 config:
Building configuration...
Current configuration : 1292 bytes
!
version 12.4
service timestamps debug datetime msec
[Code].....
I have a WLC 4404 installed and we would like to manage the bandwidth per SSID.
Today we have configured many SSID because our campus has a lot of wireless users and any SSID has only one class C subnet (/24).
We would like to configure each SSID with more subnets. is this possible ?
Additionally we need to restrict the bandwidth per SSID. is this possible ? We have some SSID for less important users and we would like to assign the bandwidth per SSID.
I am trying to restrict bandwidth for a particular LAN IP address on my network using policy maps but it does not seem to be working, My LAN IP address is 192.168.20.199 which i am trying to limit the bandwidth on.
Cisco_1841#sh policy-map interface fa0/0FastEthernet0/0
Service-policy input: Bandwidth_Allocation_In
Class-map: BWTest_In (match-all) 0 packets, 0 bytes 5 minute offered rate 0
[Code].....
I setup a WLC5508 with 2 SSIDs, one for guest traffic and another for internal users. They are in separate subnets and are routed out to the internet via 2 different isps, with the guest network going over a bonded t1 and the internal users going out the primary internet connection for the company. While this works as desired and we've verified that while on the guest network we're going out the right isp, we've encountered an issue with saturation of the bonded t1 pipe by guests. We'd like to find a way to limit a guest to a capped down/up stream if possible, with downstream being the most important. The infrastructure includes 3560 switches and AIR-CAP3502I-A-K9 access points.
View 1 Replies View RelatedI have 20 mbps internet link and I have ASA 5505 . I have to divide this bandwidth 10-10 mbps each for Voice and Data . So that both can work properly. because when I am using it for both on same interface, I am getting Voice disturbance..
View 1 Replies View Relatedi have 16MB internet speed, i want to give inside interface in my ASA only 2MB to use how can i assign it ?
ASA Version 8.2(5) !hostname ConcordeASAenable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface
[Code].....
setting up Rate Control in Bandwidth Management. It doesn't seem to work at all. I knew from some other Posts that I need to have IPS on and I do.. Is there something else I need to do.
My users are connected wirelessly to the router through three different SSIDs and I have 3 VLANS. I need to set some limitations on two of the LANS.
I am looking for some tips on managing my router. I have noticed lately our bandwidth useage has gone up and maxing our DSL line.Cacti is monitoring just for traffic trending and I am in the middle of getting NetFlow going.
Our router sits on the edge with no internal way to access it (or at least so I think right now.)
My thought is to enable NetFlow and port forward it into our network and use ManageEngine to see whats going on.I dont have any ACLs running on the router... We have two connections DSL and T1, I have them into a routing policy.Our nating and firewall sit behind the 2811.
We are looking at putting in a solution at a hotel for Free Guest WiFI.The solution would cover 4 floors and about 120 rooms and some open areas .In short the hardware would look as follows
-2500 controller
-1142LAP
-2960 PoE switch
-878 Adsl router for internet connectivity (20Mbps/1Mbps internet ADSL feed)
One of the concerns raised by the client is that they would like to make sure that no single user could eat up too much bandwidth creating problems for the rest of the users . Can the above KIT or something similar achieve this objective? As far as I can think of we would require a Proxy server .
I have a RVS4000 hardware v2 with firmware 2.0.2.7. I have a DSL modem in bridge mode and have the router set to PPPoE. Everything works fine except I want to use QOS which doesn't work fine. I have some vonage boxes set up on a switch set to port 1 trust mode is set to port and level 4 for highest priority. Port 2 I have on another switch set to priority 3. I tried turning bandwidth mangement on which doesn't seem to work at all so I don't even know if they QOS is even working. I set the max down stream and upstream provided after running a number of speed tests and setting it a little lower than my worst speed results. Once I did that I set up a rule for all traffic for rate control and set them just below the min and max I put in for isp bandwidth. I set the ip range from 192.168.1.100-190 this will cover anything that dhcp hands out and I also have a few statics set up on 192.168.1.180 and 181. However after enabling it I ran some speed tests and I still get full speed and the rules seem to be getting ignored.
View 2 Replies View RelatedI am trying to get ride of an old traffic management appliance and would like to replace it by a simple Cisco 3845.
The configuration is really simple:
Customers -- Router 3845 -- Internet
I want to be able to provide bundles to customer such 64kps garanteed/ 2mbps MIR (retail) and 2mbps garanteed no MIR (business).
I need also to specify to the router the total internet bandwitdh available (example: 20mbps symetrical).
This configuration will work ? Should I worry about any performance issue if I start to have a lot of customers ?
ip access-list extended Cust1
permit ip any sub_Cust1
permit ip subCust1 any
We have a Service Policy rule setup on our 5510 for SMTP traffic.
Problem is, this week someone sent a larger email 20+mb to dozens of recipeints and the outside interface was hitting 10mb, which is not what I would have expected with this rule in place, so I'm questioning the configuration. We know it was email because I disabled the server that receices our outbound mail to apply a signature and the traffic dropped immediately.
We have two Cisco 2811 Routers setup with a GRE tunnel that we would like to constrain the bandwidth on to replicate a satellite connectinon of 400 kbits. We tried the bandwidth command 400, but from what I understand that is only for routing metrics and not actual speed of the interface.
View 5 Replies View RelatedRouter 2811 got 3 Interfaces. One Interface connected to INTERNETProvider, Second Interface connected to Sales_Dept, Third Interface connected to Business_Dept. Internet Bandwidth in Total is 8MB. I need assistance to allocate 6MB total bandwidth to Sales_Dept and 2MB total to Business_Dept Sales_dept has 48port switch 2960, Business_Dept 24 port switch 2960. Gateway for users is the 2811 Router and both are on different subnets
View 3 Replies View Relatedi have a small network with Polycom phones connected to the sf300 switch and have the pc's daisy chained via the second switch port on each phone. i have the pc traffic running on the default vlan 1 and the voice traffic running on the voice vlan 100. can i do bandwidth management on a vlan/port basis or is that not necessary. i want to ensure that the voice traffic is never impacted by the pc traffic on the same cable.
View 2 Replies View RelatedI have some clarifications regarding ASA firewall, it can be support bandwidth management and content security at the same time. we are looking for below features in ASA5510.
IP/Policy based bandwidth management.Controll the bandwidth and allocate the bandwidth to specified users or servers.Content Security. If not, which device I need to set for Internet Bandwidth Management and content security.
We have an ASA 5525 running version 8.6(1)2 and a 10 MG pipe. I have execs that want to limit bandwidth on users for stuff like youtube, stream media, and downloads. I found the article on ‘Bandwidth Management(Rate Limit) Using QoS Policies’ so it appears our firewall can do what we want. I’m not a cisco person. My knowledge is limited when it comes to configuration – that’s why we have SmartNet.
Can bandwidth be limited on end users and/or can they limit the ‘bandwidth rate limit’ to just youtube, steaming media, and downloads? If so, what should the limit be? and I’m assume this would be for ‘incoming’ traffic only? we’re running into some bandwidth hogs – usually youtube and/or streaming media. We have a Barracuda web filter which we’ve used to block and monitor activity but I simply do not have time to babysit this all day. I should also mention we do have critical data running up and down the pipe; such as credit card processing, DB replication between in house DB and hosted website, TPCx and EDI, FTP, and such that we don’t want restricted.
We have 1 mpbs bandwidth line, but most of the time we are getting only 300-500 kpbs download speed, i want to send statistics report to our ISP, what will be best procedure to test the bandwidth report, i have checked in some websites like bandwidthplace and speedtest but these sites are not accurate, how to check the actual bandwidth we getting from ISP against 1 Mbps. We have solarwinds monitoring tool in this i have configured the WAN interface for 1 mbps
View 5 Replies View Relatedi just purchased a cisco 877 on ebay, when i got the router,, i connect to the LAN port,, but didn't get any ip from the router,, then i tried to hard-reset the router by press and hold the reset button on the back for a long time, but nothting happen, not sure if it reseted to the factory setting or not..then i try to connect to lan port again, still not getting an ip,, okay, then i try to manually config the ip to 10.10.10.5(also tried 10.0.0.5, 192.168.0-1.5) and try to connect to the router,, but still no luck, try to ping the router, no luck too, i tred to contact the seller,, he just said, the router is working for sure.. i must need an aux cable to program the router, LAN interface can't program the router, he doesn't want to refund my money,, i don't think that is true... does cisco 877 allow LAN management on default settings??
View 1 Replies View RelatedHow do I access the router's web gui management? I already enabled the ip http server and ip https commands. I have a username and password configured
I open a browser session with the ip address:URL, But I do not get the management GUI. I haven't used the GUI in many years,
Cisco Systems
Accessing Cisco CISCO1921/K9 "my-router"
Show diagnostic log - display the diagnostic log.
Monitor the router - HTML access to the command line interface at level 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
Show tech-support - display information commonly needed by tech support.
Extended Ping - Send extended ping commands.
I want to configure BGP but i am finding it very difficult to know BGP as I am new to this concept.
What is theoretical and practical approach to configure bgp??
I have to configure my office router 2811 for two ISPs which will be acting as fail-over.
I have to start it from scratch.
I just bought an additional router for my network and I'm in the process of setting it up.I have however hit a snag with enabling ssh on the device. It is a cisco router 2811 running IOS 15.0 (refer below to my attempts)
View 3 Replies View Relatedhow many extra interface port can be plugged in to the 2811 router ,there are 2 fixed FE port on this router and i have 3 connection i.e one mpls link , one internet link and one sip trunk .. some body confirm me that i can insert module in 2811 ?
View 5 Replies View RelatedHow to replace fan incisco 2811 router in live or down condition?
View 2 Replies View Relatedwhen I got past my current hang up, I marked the thread as answered, so I wasn't sure if I should start another or continue on...
I've tried going through that troubleshooting doc, but I still can't figure this out.
When turning on debug for the 2811, I'm not seeing any thing.
show debug
Cryptographic Subsystem: Crypto ISAKMP debugging is on Crypto ISAKMP Error debugging is on Crypto IPSEC debugging is on Crypto IPSEC Error debugging is on
#show crypto sessionCrypto session current status
[Code].....
I configured Any Connect SSL VPN on Cisco 2811 router. It works perfectly when I lo gin via web and run secure mobility client. However, when I connect directly from the mobility client connection fails. It does not even ask me for username and password.
----------------------------------------------------------------------------------------------------
Mar 7 21:36:47.613: %SSLVPN-5-SSL_TLS_CONNECT_OK: vw_ctx: UNKNOWN vw_gw: VPN_GATEWAY i_vrf: 0 f_vrf: 0 status: SSL/TLS connection successful with remote at
Mar 7 21:36:47.617: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.621: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.745: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.749: WV: Entering APPL with Context: 0x49233618,
[Code]........
--------------------
I have not figured out yet, why mobility client works when launched from the web and why it does not work directly.
I have cisco 2811 router and two ISP copper line. How can configure it as BGP router.
View 11 Replies View RelatedWe currently are using 2811 router for internet Via IPSEC tunnel.Download speed is 30 Mbps and Upload speed is 6 Mbps.
But we are getting not more than 4 Mbps download speed. We did open Tac case and as per Tac 2811 router is not for 30 Mbps.Can any suggest proper model. We need 2 FastEthernet/Gig and one serial port.
I am looking to upgrade a 2811 router to 15.1.2T and see in the release notes that this image is only compatible with the "C Series" older ISR routers? What is a "C Series" ISR and how do I know if I have one?
View 4 Replies View Related