Cisco :: 2811 - WLC - Cannot Reach Management IP From LAN
Jul 4, 2012
I have a 2811 (running 12.4(15)XZ) with a WLCM (4.2.209.0).
I have reset the configurations on both. Set FE and WLCM IPs on the router and gave WLC Management and AP manager addresses. All + PC are on the same subnet. Router pings all addresses besides AP-manager(intended). WLC CLI cannot ping PC and PC cannot ping (nor http) to WLC. PC can however ping and telnet the router on both the FE and WLCM IPs.
I followed the guides on WLCM configuration, did I miss something?
How can I access the management IP and the web GUI?
2811 config:
Building configuration...
Current configuration : 1292 bytes
!
version 12.4
service timestamps debug datetime msec
[Code].....
View 17 Replies
ADVERTISEMENT
Mar 12, 2013
In one of my client location I have deployed one Cisco 3560X (core switch) and one SG-200-18 (access switch). I’ve configured three vlans (vlan 2, vlan 3 and management vlan 1), relevant trunking and I’ve connected two pc to the access switch to vlan 2 and 3 respectively. So far everything (including inter-vlan communication) works fine, except that I couldn’t reach the vlan 1 (management vlan) devices (access switch and core switch) from any pc which is connected to either vlan 2 or 3.
I’ve configured the “port VLAN membership” settings in SG-300 as follows,
Interface mode Administrative vlans Operational vlans
GE 2 Access 2UP
[Code].....
View 4 Replies
View Related
Mar 28, 2012
I've just reset our WISM2 in the test lab back to factory default as I needed to reconfigure the 6500 and the WISM2 itself. Bearing in mind I had it working before.I've just renamed and re-addressed some of the vlans so things flow better and make it easier to add more WISM2s in the future.Now I've run through the initial configuration and it's rebooted ok and show WISM status is showing Oper-Up and there's a port channel 407 been created as I would expect. However, I am unable to get to the management interface via GUI or SSH. In fact from the 6500 I can't even ping the management interface (but I can the service port).The Vlans have been changed in the 6500 config so it knows the native-vlan and service vlan etc and all the vlans are up/up.
View 17 Replies
View Related
Feb 11, 2012
I have 25 of these routers installed behind various providers and transport (DSL, Cable, UVerse). At sites where I have static IP, I can't reach any service inside, and in fact can't even reach the router for Remote Management. At all times the users indoes can do whtever they like, the have Internet access.
At sites where we draw a dynamic IP or use PPPoE, I can reach services and manage the router until a known issue stops the inbound traffic.
View 3 Replies
View Related
Aug 29, 2012
I am trying to use GNS to simulate this, but a bit difficult to achieve this. May I know can the Cisco Router handle below requirement? Example Cisco 2811
1) Bandwidth management based on IP Address or Subnet? For example; allocate 1Mbps (CIR) and 10Mbps (BIR) to 172.16.1.10
2) Can the Cisco Router control the inbound and outbound bandwidth?
3) Can you share the sample config?
View 7 Replies
View Related
Aug 15, 2011
I'm trying to reach Celebs4.UsThe first time I tried (earlier today), I was able to access, but when I clicked on one of the images I recieved a "The connection has timed out" error. I have not been able to open the site at all since that very first time.I have done the following:- tested it in both FF and IE- run tracert (seems like the problem is on the site's server end, but everyone else is able to connect fine)- flushdns- clear cachemy tracert: :: pokIt
View 5 Replies
View Related
Apr 15, 2012
for the last 5 days or so, my internet was acting weird, disconnecting every 20 mins or so, i had an old linksys router, no clue on the modem, but all of it's about 7 years old, i got a replacement, Motorola SBG6580, my connection is somewhat better, but my ISP says they can't ping my router/modem
View 1 Replies
View Related
Jul 7, 2012
I've setup a SSL VPN to a ASA 5505 and can connect.
VPN network 192.168.2.0 /24
Inside Network 192.168.1.0 /24
Outside is connected to Router.
I am trying to RDP to a win server on the inside network but I cant get to it. Can not even ping 192.168.1.1 or (not sure if I could anyways) 192.168.2.1...
I added a ACL on the outside interface and then inside interface permit ip any any but still no ping or RDP...
New at VPN and have survived so far on cisco docs but this problem is evading me.
: Saved
:
ASA Version 8.2(5)
!
hostname ciscoasa
[Code]....
View 1 Replies
View Related
Sep 30, 2011
I have an ASA running 8.2(2).I am trying to get the network on the inside interface to be able to communicate through the outside interface and on to the internet.
View 18 Replies
View Related
Nov 28, 2012
since a few days I'm trying to solve a problem. I've successfully established an IPSec tunnel between two local LANs. In the main office I'm working with a ASA5510 CLI 8.4 and a static public IP address. The branches are using different Cisco 8xx routers and dynamic public IP address. The following picture shows the current configuration:As I mentioned an IPSec Tunnel between the main office "Intern"-LAN 192.168.1.0/24 and an outside LAN 10.10.0.0/24 is successfully established. Now there is a new intern "Admin"-LAN 192.168.2.0/24 at the main office. The users from the outside LAN 10.10.0.0/24 need the possibility to reach this new intern "Admin"-LAN.Can I simply route the traffic from 10.10.0.0/24 to 192.168.2.0/24 via the existing IPSec-Tunnel? Or need I a new IPSec tunnel between the outside 10.10.0.0/24 LAN and the new "Admin"-LAN 192.168.2.0/24?
View 5 Replies
View Related
May 27, 2012
i'm setting up vlan and inter-vlan routing in my lab. My vlan work well (routing between them and dhcp relay) on the LAN side of the ASA but they cannot reach internet trough the ASA.
Here my ASA settings :
Note : I know that the physical interface musn't have an @IP but my present network needs one to work. I'll fix this during my next tests.
: Saved
:
ASA Version 8.2(1)
!
[Code].....
View 8 Replies
View Related
May 23, 2013
We set up a 1941 Router with the Cisco Configuration Professional Tool. The VPN Tunnel works and i get an IP Adress from the pool. But i cant reach any devices in the VLAN10 Network. Do i forget anything ?
Here is the config from the Router:
version 15.1
parser view CCP_Monitor
secret 5 $1$FnN7$Qr.mbJbPOuOH7Te6MD1.I0
commands configure include end
[Code].....
View 3 Replies
View Related
Oct 13, 2011
I have a (central) ASA5510 acting as a EasyVPN server and a number of (remote) ASA5505 as EasyVPN client. All the communication works fine between the different networks. The issu is the ASA itself. The remote ASA can ping the central ASA on it's internal IP-adress, but it can't ping any other resoruces at the central network. If I ping the DC at the central network from the remote ASA I get a deny in the central ASA with source address as the public IP-adress of the remote ASA and destination of the internal address of the DC. If I from the remote ASA do "ping inside ip-of-central-dc" it work's like a charm, but "ping ip-of-central-dc" dosen't work.
View 3 Replies
View Related
May 9, 2012
I have configured a Remote access vpn on pix 525 with 7.2(4) code. After getting connected (with ip address assigned from the pool) i am not able to reach any of the internal networks. [code]
View 3 Replies
View Related
Jul 6, 2012
I've setup a SSL VPN to a ASA 5505 and can connect.
VPN network 192.168.2.0 /24
Inside Network 192.168.1.0 /24
Outside is connected to Router.
I am trying to RDP to a win server on the inside network but I cant get to it. Can not even ping 192.168.1.1 or (not sure if I could anyways) 192.168.2.1...I can ping from the 192.168.1.0 net to 10.0.0.0 and 192.168.2.0 without issue but not the other way around....I added a ACL on the outside interface and then inside interface permit ip any any but still no ping or RDP...
: Saved
:
ASA Version 8.2(5)
!
hostname ciscoasa
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code]....
View 1 Replies
View Related
Jun 18, 2012
I am able to reach VPN clients (Anyconnect) only from hosts directly connected to the ASA's inside interface subnet. However, hosts on other internal subnets (177.1.10.0 & 177.1.11.0) are unable to connect to clients on VPN. The ASA is running ver 8.4. [code]
View 8 Replies
View Related
Feb 8, 2011
I have remote access vpn setup and I can get connected with no issues. I assigned the vpn a pool of addresses from the end of my inside interface subnet. When connected I can ping any device on that subnet, I can also connect to my switch on the same subnet via my browser. I can not however access any device located in my dmz while connected. This is a new setup I'm testing but I need vpn user to be able to use rdp to connect to machines in the dmz.
Result of the command: "show running-config"
: Saved
:
ASA Version 8.2(1)
!
hostname ASA1
domain-name
enable password encrypted
[code].....
View 4 Replies
View Related
Oct 9, 2012
[URL]
This router support bridge mode, but i'm unable to configure it. There's no such option in the web configuration page, but the manual says that disabling nat activates automatic routing mode. Unfortunately all i get when i disable nat is to be unable to reach any wan address.
By watching the generated routing table on the wrp400 (when in NO nat mode) i see that 0.0.0.0 is correctly set up to use the external border router, but any incoming packet from the wrp400 lan port isn't routed there.
Also, i don't get any dhcp from the external router, this means the wrp400 is blocking it.
how to set up a bridge mode between wan and lan ports
View 1 Replies
View Related
Mar 12, 2013
I am facing the following problem. SmartPhone is connected WiFi hotspot. Suppose SmartPhone ip is 10.0.2.2 and hotspot ip is 10.140.13.12. I am able to send data from smartphone to a server(over internet) which has static ip and sender details in server are hotspot ip. Problem is sending data from server back to smartphone. Tried sending to 10.0.2.2(smartphone) from server but packets are not received.
View 3 Replies
View Related
Sep 1, 2012
I have got a problem with my LAN connection. I can't connect to the internet anymore and I can't reach my router. I rebooted my router several times, but that didn't work. I thought my network adapter was broken, so I bought a new one and reinstalled the driver, but it did not work. My router does recognize my computer though. When I tried to boot in safe mode with network opportunities, I was able to connect with my router and internet. I can't use System Restore as I don't have any restore points.
View 10 Replies
View Related
Mar 27, 2011
I have two desktop computers upstairs.The main pc has the Linksys G Router and the other pc is wireless with a network adapter. All works fine here.Downstairs and on the other side of the house, I use my laptop which is wireless to the network. I also have a 46" hidef tv hooked up to a blu ray player and also connected to the network with a wireless adapter. I use Netflix to stream movies and seem to be having a problem with the signal in this room, both on the tv and my laptop. I sometimes only have 2 bars on my laptop and frequently get disconnected to the internet. When I am streaming movies or tv series, I get frequent stops and starts.
I am guessing that the signal is just not strong enough to reach this far from the router. Would switching to an N router be better for streaming? Would another G router downstairs solve my problem?
View 4 Replies
View Related
Aug 16, 2012
Just got a brand new router this morning. Hooked it up to the modem, called Bright House and had it set to bridge mode, set up our wireless range extender and everything was fineMy dad's mac laptop was able to connect as well as my win7 desktop. When my brother tries to connect using his win7 laptop, though, he can connect to the router but not to the internet. He keeps getting limited access. He was able to connect and use a neighbor's wireless (but obviously we don't want to be doing that) so we know it's at least working
View 5 Replies
View Related
Feb 10, 2011
I'm having some troubles with SSLVPN connectivity. I've setup SSLVPN at one site and it works great with web access, file share, RDP plugin etc. at the local LAN on that site. But I also would like to reach another site (connected with an IPSEC tunnel). Is this possible? if it is, how do I do it?Both firewalls are ASA5505, one 8.31 and one 8.22 Just a note, it works to connect with IPSEC client and reach the remote site just fine.
View 8 Replies
View Related
Oct 31, 2012
I have created a connection gateway-to-gateway between RV220W and RVL200, is doing without any problems.For example, I can ping the gateway on the other side. But when I connect trough RV220W QuickVPN (or PPTP) I can not reach the gateway (RVL200) or any host behind it.
View 4 Replies
View Related
Dec 9, 2012
I have a cisco 2851 router as the edge router, I have a 3750G and a 3560G switch and configured intervlan routing with four vlans, also connected to the switches a four servers and one has active directory and a dns server.i am able to ping from all te servers fine from different vlans and the servers are able to ping the edge router. the problem I am having is with DNS, in the edge router i have configured the isp's dns server address in ip name-server and i am able to reach the outside world.
the problem im having is the servers are not able to reach the outside, do i need to do something in the edge router to forward it to the 3750g or do i have to add my isp's dns servers on the 3750g with ip name-server.
View 5 Replies
View Related
Oct 12, 2011
An 1841 is conencted to the internet by DSL, it works fine. I have added it to the 10.98.8.x subnet off a 3750 switch.When I connect other devices to the same switch port, I can ping/browse to them fine, but when I connect the 1841 I can only ping it from the 3750, not another subnet connected to the same router. [code]
View 2 Replies
View Related
Mar 3, 2012
I have this strange problem with my Macbook pro, when I connect it to my cisco 2940 8 port switch then I can reach my ISP (websites eg. google.com) in like 2 minuttes, then something is happening on my router, because suddenly I can´t reach my ISP
This is what I have found out so far:
1. when I lose connection to my ISP then I can only ping internal ip addresses eg. another computer in my network
2. if I renew my ip address on the Macbook then it works again in 2 minutts, then the same happens again. This is my network setup:
Router -> Switch 1 -> Switch 2
I also know that it is not the Macbook, because it have got a new motherboard, and it have been reinstalled
also if I use the Macbook on a other network then it works fine.
All my other computers ( windows and linux ) works fine, no problems.
To me it looks like it is a Nat and/or DNS problem, but I can´t fine out what it is.
View 7 Replies
View Related
Nov 30, 2012
I have been at this for the past few hours now. I just cannot get this device to pass through traffic to the internet. Here is the basic topology:
Default Gateway (ISP): 208.118.125.129/29
IP of outside int (e0/0): 208.118.125.130/29
ip of inside int (e0/1): 10.1.1.1/24
igniteCSGfw(config)# sho run
: Saved
:
ASA Version 8.0(4)
[Code].....
View 3 Replies
View Related
Mar 6, 2012
I have been configuring a cisco ASA 5520, everything is working fine but when i create an ACL:
-access-list OUT extended permit ip 172.16.x.x 255.255.255.0 any
-access-group OUT out interface outside
i added ports like www or 443 and it is not working to Internet access a router is before to my firewall connected to my headquater, i can see my private networks but i cannot able to reach Internet access,
View 3 Replies
View Related
Feb 21, 2013
I have set up a Guest Portal with WLC 5508 7.4 and ISE 1.1.1 ;everything is OK, except one thing: the Guest VLAN, associated to the Guest SSID is, actually, a DMZ behind my customer firewall and the DHCP parameters provided to the wireless Guest equipement connected on this VLAN include the public ISP DNS servers addresses, not the customer internal DNS serveurs addresses;this seems OK since the idea of this Guest SSID is to give a pure Internet access to the Guests, and no connection at all towards the customer internal servers;
the problem is that, when the wireless guest receives the redictect URL from ISE (URL to access the ISE Guest Portal), this URL is based on the ISE DNS name, not on its IP address; so, the PC can't resolve this internal DNS name by using the ISP DNS servers addresses provided by the DHCP server, and, so, it can't access the Guest Portal at all ;Apart from changing those DNS values in the DHCP server (the customer does not accept this solution), how could we solve this problem ?I have tried to code manually , in the CWA Authorization profile, the equivalent URL redirect via the CISCO av-pair as follows : [code] but, it does not work, since the sessionIdValue variable is not replaced by its real value when sent to the wireless client
View 4 Replies
View Related
Oct 10, 2011
We had setup a wired/wireless LAN using Cisco 881W router for one of our client. Wired lan works OK but we have issues with wireless. Users on wireless LAN can connect to the wireless network, but cannot browse the Internet. The wifi network does not give out an ip address to the client so client cannot get to the default gateway and Internet. Not sure what part of config does not work.
##### sh runn #####
881WiFi#sh run
Building configuration...
[Code].....
View 10 Replies
View Related
Apr 13, 2013
-cisco 2651xm router
-cisco 1760 router
I have a cisco 2651xm router here at home, and at another remote location I have a cisco 1760 router, both are connected to the internet via adsl (WIC1-ADSL card).The problem is that from home I can't connect to the snmp-service on the 1760 router. I'm using a PC that's on the LAN of the 2651XM router, the blockage is in the 2651XM router, because if I swap it for a cheap plastic domestic router I can get snmp data from the 1760 router, and this is without any port forwarding in the domestic router. What config do I need on the 2651XM router so it will pass this traffic?
View 3 Replies
View Related
Apr 3, 2011
We are facing strange issue in our network. We have a remote branch which is connected to main branch using Leased Line. Remote branch is having Cisco 1700 Router. Every day in the morning time the remote router is unreachable. We are not able to reach (ping/telnet) the remote Router but able to reach L3 switch/ LAN behind this router. The users from remote branch is also not able to reach the local router but they are able to ping the Main branch.Users in the remote branch are not able to access any resources in the main branch during the issue.
During the issue, we have checked the remote branch router and found the CPU utilization of the Cisco 1700 router is very high (99%). If we run "Show process CPU" command (please find the attachment) specially IP input process is very high (97%).
View 1 Replies
View Related
