Cisco Wireless :: 881W - Wi-Fi User Cannot Reach Internet
Oct 10, 2011
We had setup a wired/wireless LAN using Cisco 881W router for one of our client. Wired lan works OK but we have issues with wireless. Users on wireless LAN can connect to the wireless network, but cannot browse the Internet. The wifi network does not give out an ip address to the client so client cannot get to the default gateway and Internet. Not sure what part of config does not work.
##### sh runn #####
881WiFi#sh run
Building configuration...
[Code].....
View 10 Replies
ADVERTISEMENT
Sep 26, 2012
I have one WET200 Wireless Brigde, connected to internet router... I can't use the infraestructure mode to broadcast the ssid to wireless cliente like laptops,
Only can use the ad hoc mode, but the wireless clients dont reach the internet from adhoc connection trought WET200...The datasheet saids "client only" for WET200, what is the diference between client only and Access Point mode? ??
View 2 Replies
View Related
Sep 30, 2011
I have an ASA running 8.2(2).I am trying to get the network on the inside interface to be able to communicate through the outside interface and on to the internet.
View 18 Replies
View Related
Sep 1, 2012
I have got a problem with my LAN connection. I can't connect to the internet anymore and I can't reach my router. I rebooted my router several times, but that didn't work. I thought my network adapter was broken, so I bought a new one and reinstalled the driver, but it did not work. My router does recognize my computer though. When I tried to boot in safe mode with network opportunities, I was able to connect with my router and internet. I can't use System Restore as I don't have any restore points.
View 10 Replies
View Related
Aug 16, 2012
Just got a brand new router this morning. Hooked it up to the modem, called Bright House and had it set to bridge mode, set up our wireless range extender and everything was fineMy dad's mac laptop was able to connect as well as my win7 desktop. When my brother tries to connect using his win7 laptop, though, he can connect to the router but not to the internet. He keeps getting limited access. He was able to connect and use a neighbor's wireless (but obviously we don't want to be doing that) so we know it's at least working
View 5 Replies
View Related
Nov 30, 2012
I have been at this for the past few hours now. I just cannot get this device to pass through traffic to the internet. Here is the basic topology:
Default Gateway (ISP): 208.118.125.129/29
IP of outside int (e0/0): 208.118.125.130/29
ip of inside int (e0/1): 10.1.1.1/24
igniteCSGfw(config)# sho run
: Saved
:
ASA Version 8.0(4)
[Code].....
View 3 Replies
View Related
Mar 6, 2012
I have been configuring a cisco ASA 5520, everything is working fine but when i create an ACL:
-access-list OUT extended permit ip 172.16.x.x 255.255.255.0 any
-access-group OUT out interface outside
i added ports like www or 443 and it is not working to Internet access a router is before to my firewall connected to my headquater, i can see my private networks but i cannot able to reach Internet access,
View 3 Replies
View Related
May 20, 2013
PCs --> SG500(4 vlans) --> rv042 --> Internet..vlan 1 is able to reach the internet..vlan 2-4 cannot reach the internet, but can reach vlan 1.
View 2 Replies
View Related
Apr 11, 2011
I'm having trouble setting up local LAN (reach inside network when VPN connected) and Internet access (reach internet when VPN connected) for my VPN CLients when they are connected to my VPN, They can connect, no problem there, but I can't reach any resources when connected. My pings time out, both to my inside network and to public ip adresses, the only thing I'm able to ping is my ASA (172.16.30.1), and I don't se any routes under "Status/Statistics/Route Details" in my cisco VPN Client (when connected).
Here's my config
ASA Version 8.0(3) !hostname KardesASAdomain-name default.domain.invalidenable password XXXX encryptednames!interface Vlan1 nameif inside security-level 100 ip address 172.16.30.1 255.255.255.0 !interface Vlan10
[Code]....
View 14 Replies
View Related
May 30, 2011
Att says they are giving us 3mb/sec but we get 300kbps and speed tests from anywhere say we get 2.5 to 2.9 mb/sec yet even on unlimited bandwidth downloads(like torrents) with thousands of seeds connected and a few peers they never get faster than 340kb/sec.
View 9 Replies
View Related
Jun 4, 2012
Since some days we have a ASA5510, we connected it on a Windows Vista Laptop via ethernet cable (using at the back of the router the mgtm slot) and connect it on the network slot on the laptop. Laptop is getting IP addresses automatically.
Now we tried to reach the router in the Internet Explorer using: http://192.168.1.1, but we could not reach this site. When I try to ping the router via cmd and typing ping 192.168.1.1 I get answers.
For us it is very important to change the IP address of the router, as he will be used in a network with 10.xxx.xxx.xx addresses.
View 2 Replies
View Related
Jan 24, 2011
I've got a Cisco 881W Router and I am trying to set up the wireless Network. I've managed to get the SSIDs up and running, but I can't see to get DHCP addresses going from the router to the access point and Laptops .When i am connecting laptop directly to Router ethernet port i am able browse and seeing DHCP address. [code]
View 7 Replies
View Related
Sep 27, 2012
I'm putting together a design for a new office with the following requirements:
10 VPN users.For Ethernet – 24 ports POE 10/100/1000
Probably go with VZ FIOS so EthernetAbout 2000 square feet so 2 WAP's should do it I'm thinking a CISCO881W-GN-A-K9 ISR with a SRW224G4P-K9-NA switch should do the trick. This will give me an integrated AP but I need a second one. Do I need to order an autonomous one or does the 881W do some sort of WLC function?
View 1 Replies
View Related
Dec 20, 2012
I am trying to setup a remote PC over a wireless access Point/Bridge to our FIOS router. Pic of setup is shown below. Everything is connected, there are no errors or security warnings shown in the ActionTec MI424 router. The RemotePC IP shows up as an Active Ethernet client in the Router config app. Moreover, I can run the connectivity test from the router app to the RemotePC and it passes that, and I can PING from the RemotePC to the Router. Yet I cannot reach the Internet from a Browser on the RemotePC (192.168.1.75). I am using (2) DLINK DAP-1522 Access Point/Bridge units and they have worked as expected. I set the Router log to list any blocked IP traffic as well, and it does not show anything being blocked from the RemotePC (192.168.1.75). So why can't I reach the Internet from the RemotePC? Seems like a gateway problem or I need to make some config changes in the Router.
View 2 Replies
View Related
Dec 8, 2010
Is the max wireless speed on the cisco 881w 54mbps even though it has 802.11n hardware? What about the 891w ?
View 13 Replies
View Related
Jul 7, 2011
The 801 AP on my 881W reboots every other day or so, randomly, on its own. The router / AP works great otherwise, no other issues. I checked the error log and I see no indications of why it would be doing this.
ap#sh ver
Cisco IOS Software, AP801 Software (AP801-K9W7-M), Version 12.4(25d)JA, RELEASE SOFTWARE (fc1)
[Code]......
View 30 Replies
View Related
May 21, 2013
How to upgrade the IOS of the Integrated wireless AP in a Cisco 881W using TFTP server (I do have software)Router side is not an issue it is the integrated AP that gives problem?
View 14 Replies
View Related
Feb 2, 2012
I have a Cisco 881W configured for wireless (just a PSK, nothing special). I can get out to the Internet OK and browse to everywhere except my own websites.
It runs on a connection that does not connect directly to my network, but our website is available to the world externally.
Now, from the router a traceroute and ping work fine to our website but from the wireless connection I can get to everywhere else on the web but our website. A traceroute just stars out. I'm using 8.8.8.8 as a DNS server and nslookup resolves the DNS.
I can't set a DNS server or domain server on the ap on the 881W so are there any commands I can use to see what's going on?
View 2 Replies
View Related
Jan 17, 2011
Just recently got a new 881W router. i have downloaded the 2.4 software upgrade. I go into the Office extend AP login and i get just a enter button. when i click on the enter button the AP page does not come up.
View 7 Replies
View Related
Mar 30, 2013
1 router 881w with a site-to-site VPN connected to a switch and a wireless which allows internal users to access the VPN via wireless (this is like a backup, if the switch fails, then they can use the wireless). Everything's working fine so far. Now I want to configure a second WLAN for guest but I'm not really sure if this configuration will work:
ROUTER:
ip dhcp excluded-address 192.168.100.1 192.168.100.200
!
ip dhcp pool GuestNetwork
network 192.168.100.0 255.255.255.0
default-router 192.168.100.1
dns-server 8.8.8.8
[code]....
If it's not clear I want that everyone that is connected to the guest WIFI receives an IP address from the range I wrote before and then goes directly to the internet.
View 11 Replies
View Related
May 9, 2013
We've had a Cisco 881W set up in one of our remote offices for a while and the wireless has been fine. Yesterday I got a call saying that the wireless was no longer working.
I went over and it's true, the SSID is no longer broadcasting. I reloaded the router but it's still the same. I tried to get access to the embedded ap and I get this
RTR#service-module wlan-ap 0 session
% telnet connections not permitted from this terminal
RTR#
Now I've not changed anything on the configuration since it went in and it was working before. Has the embedded ap died? The embedded ap is still showing as a component in show hardware.
View 15 Replies
View Related
Oct 15, 2012
I recently purchased a new Cisco 881w router (last Friday).I have configured the 'wired' part of the router with little trouble, but the wireless side is proving a little challenging.I have read a number of posts complaining about the firmware version installed on my device being very buggy.The version of the firmware on the wired part is: Version 15.0(1)M8, however, the firmware on the wireless side seems to be: Version 12.4(21a)JA1 - the version reported as buggy. The former has a version date of 2012, with the latter being 2009.I have tried to download a newer version, but the site is asking me to provide a support contract.I wouldn't mind buying a support contract if the thing worked in the first place and I was trying to add some feature after it had been working for a while.
View 1 Replies
View Related
May 9, 2012
I have a Cisco 881W and I would like to basically some how bridge the Cisco router to my netgear router. This is what I'm trying to achieve:
Cable Modem ----> Netgear Router ~~~~~ via wifi ~~~~> Cisco 881W ------> FastEthernet Ports
I've tried setting the Cisco 881W with station-role non-root with the SSID of my netgear router, but I get the error %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response whenever I try to bridge it.
Is bridging the Cisco router via wifi to the Netgear Router something that is not possible or is it an error on my part?
View 2 Replies
View Related
Nov 21, 2012
Is it configurable to allow wifi user to user traffic on WLC 5508?
View 4 Replies
View Related
Feb 20, 2012
I'm setting up a couple 881W cisco routers to use Unified wireless and am running into a bit of a brick wall.I've read through the "Upgrading to Unified Cisco Software" section of the following article:[URL]The problem is, I can't run the "service-module wlan-ap0 bootimage unified" command. The keyword "bootimage" does not exist. The router is licensed for advipservices and I'm running version 15.0(1)M4 on the router. AP is currently running version 12.4(21a)JA1. why the bootimage command doesn't appear? Will I need to downgrade the router IOS to 12.4?Additionally I'm having trouble finding an answer to the following:Is there a way to set up the embedded AP on the same network as the Data VLAN on the router, or do I need to create a separate IP network for the embedded AP? I've tried using 'ip unnumbered vlan10' (vlan10 is the data vlan) on the wlan-ap0 interface but then when I try opening a session to the AP it doesn't connect.
bcp4n51001#service-module wlan-ap0 session
Trying 10.199.62.1, 2002 ...
% Connection timed out; remote host not responding
This is my Vlan10 setup for one of the routers:
interface Vlan10
ip address 10.199.62.1 255.255.255.0
ip helper-address 10.151.103.254
ip helper-address 10.150.1.254
ip pim sparse-mode
View 8 Replies
View Related
Nov 9, 2012
I have an integrated 881W with a built in 801 access point. I'm interested in increasing the range of my AP. I'm interested in considering any configuration changes while still maintaining support for N. I've included a copy of my running config.As well, I've heard of high gain antennas. I'm using the default antennas that came with the 881W. If there are better antennas that I can buy to increase my range, I'm interested in considering that as well.
View 10 Replies
View Related
Aug 19, 2010
I was trying to upgrade the IOS image of the AP and I did a wrong manip.
I downloaded the IOS image (ap801-rcvk9w8-tar.124-10b.JA3.tar) from my TFTP server to the flash of the AP. Everything went find so far. But than I did an archive archive download-sw /overwrite ap801-rcvk9w8-tar.124-10b.JA3.tar and my AP reboot in LWAPP mode.
I should have done: archive download-sw /overwrite tftp://10.0.0.1/ ap801-rcvk9w8-tar.124-10b.JA3.tar instead!
Now I don't how to go back to autonomous mode. archive commando is not available anymore in LWAPP mode.
View 4 Replies
View Related
Feb 27, 2011
I have a laptop with 2 user account (one for me - administrator and the other for my eleven year old son). Connection is wireless. Until a few months ago everything was working fine and then the problems started: my son could no longer connect on the internet with Explorer and Google Chrome but I managed to connect it via Firefox. And it worked until yesterday. As of yesterday he can no longer connect to the internet even with Firefox. I tried again as an administrator to reinstall Google Chrome, but the icon is shown only on my user account. I took a completely new browser - Opera, but fails to connect. When I go to Diagnose & Repair connection problems - shows no problems. On my account everything is working properly. OS is Windows Vista Home Premium
View 2 Replies
View Related
Dec 18, 2011
I have a Cisco 881W that will no longer boot/operate properly if the internal radio card is installed. If the card is installed, all I get is the following...
System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 2009 by cisco Systems, Inc
[Code]....
if I do a dev I get nothing. If I do a dir flash: I get "bad device name". My cookie shows FF in all positions.
If I remove the entire WiFi Radio card (both boards), then It boots fine, cookie appears intact, devs appear, IOS loads, just without the WAP.
Any chance this is a matter of a file getting deleted or corrupted or is this certainly bad hardware? The router sans Wifi appears fully functional.
View 2 Replies
View Related
Mar 19, 2012
I simply need to recover an embeded access point password.
I have the passwords to the 881-w router, but passwords to the embedded access point I don't have.
What is the recovery process for it, or the password reset process for the embedded access point.
View 8 Replies
View Related
May 25, 2013
I have 5508 controller in my lab. I am working on a project to set up a public internet but with some condition.
- User should able to connect to the SSID without any authentication.
- Once user will connec to the SSID it should redirect to an external URL which indicates terms and condition and email address field.
- User should enter his/her email address in email addrss filed and click I accept button.
- Once that is done then he/she is allowed to access internet.
We are not sure how can we achive this as I do not know what should be the return value for WLC to allow that user to go through or what should be the settings on the WLC to redirect to the page.
I have seen a settings on web authentication for external URL but I guess it is only for username passwor or Radius authentication. While in this case I do not want to use any authentication just an accept buttor or Decline button and all good to go.
View 2 Replies
View Related
Mar 1, 2011
Recently i bought a new printer: Epson SX620FW, I've tried many things, but I can't connect it wireless to my network. Ive downloaded and installed the latest drivers and software from the internet. My PC is connected with a cable to my wireless router. When I connect the printer with a cable to my router everything works perfectly. But I want to connect my printer wireless. On the printer I disconnect the cable. I followed the wireless wizard setup on the printer and I connect to my wireless router. This is confirmed by an ip adress on the printer. Also in the menu of my router I find the ip adres of my printer in the DHCP clients list. So far so good. But from my PC I can not find the printer in my network. I also cant ping my printers ipadres. When I connect the UTP cable to my printer again, I can ping the ip of my printer.
View 2 Replies
View Related
Feb 8, 2013
I have a new EA4500 router and I cannot configure it to reach the 450 mbps that is supposed to get.
I have it configured as follows:
Dual Band- 2,4 and 5 GHz
2,4 in 20MHz only - 5 GHz in 40 MHz only
2,4 Mixed - 5 Ghz only N
WPA2 personal in both
Channel - automatic (both)
I have checked that the 5 Ghz network can only use 4 channels: 36, 40, 44, 48. Where are the channels up to 100 (or more)? How to get all the power of the router?
View 2 Replies
View Related
