I have one WET200 Wireless Brigde, connected to internet router... I can't use the infraestructure mode to broadcast the ssid to wireless cliente like laptops,
Only can use the ad hoc mode, but the wireless clients dont reach the internet from adhoc connection trought WET200...The datasheet saids "client only" for WET200, what is the diference between client only and Access Point mode? ??
I decided to upgrade the firmware in my WET200 so downloaded the latest firmware v1.0.10-ESTI filename WET200-ETSI_v1.0.10_200802_fw.img.Update seemed to go well, and the message came up rebooting please wait.Waited about 5 minutes whilst the message stayed the same, decided to try and close my explorer window and connect again, nothing happened.Tried to reset the unit by holding in the reset butting again nothing seemed to happen. The unit had been set up with the ip 192.168.113.4 before the upgrade but this is now unreachable, also tried the default of 192. 168.1 .226. Anything I can do/try to restore my unit, or did the update brick it?
View 3 Replies View RelatedI've just purchased 2 WET200 wireless bridges for our organisation, with the intention of using them to create a wireless bridge between 2 buildings.I've followed this guide here: url...and I'm unable to configure any kind of security other than WEP. More disconcertingly, the foot of that guide states:WET200 only supports WEP for the Wireless Security."Surely this can't be the case? All the marketing blurb states clearly that the WET200 supports WPA2, and I would have thought WPA2 was a given for any wireless product sold today, especially a business grade product. Have I misunderstood what this device can do?
View 4 Replies View RelatedI just purchased a WET200 wireless bridge. After trying a very long password for an enterprise certificate the bridge restarted and I have not been able to contact the device with the default 192.168.1.226 ip address. I have tried performing a reset even by holding the reset button in for a minute. The bridge will not ping either. I do have a power light and the wireless light flashes and the Ethernet port lights function when plugged into my laptop.
View 3 Replies View RelatedI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedI have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedI have been configuring a cisco ASA 5520, everything is working fine but when i create an ACL:
-access-list OUT extended permit ip 172.16.x.x 255.255.255.0 any
-access-group OUT out interface outside
i added ports like www or 443 and it is not working to Internet access a router is before to my firewall connected to my headquater, i can see my private networks but i cannot able to reach Internet access,
How do I connect my wireless access point router to the internet so that I may use my ipad?
View 2 Replies View RelatedAt home I have a wireless access point that I use to connect my laptop #1 to the Internet. On laptop #1 IP address is set to 193.49.21.65. This IP address also Subnet Mask and other addresses are given by my Internet Service Provider. Everything works just fine but lately I bought another laptop (laptop #2) and now my aim is to connect both laptops to the Internet. Unfortunately, I can't make that happen. Only one of my laptops having IP 193.49.21.65 set can connect to the Internet.
[URL]
So is there any way to have an Internet connection on both of my laptops without having to buy any new equipment?
We had setup a wired/wireless LAN using Cisco 881W router for one of our client. Wired lan works OK but we have issues with wireless. Users on wireless LAN can connect to the wireless network, but cannot browse the Internet. The wifi network does not give out an ip address to the client so client cannot get to the default gateway and Internet. Not sure what part of config does not work.
##### sh runn #####
881WiFi#sh run
Building configuration...
[Code].....
I have an AT&T Gateway Wireless router to connect to Internet with my wired computer. In another room, I have another wired computer I also use to connect to Internet. I never have problems connecting to Internet from computer that is hooked up to the router, but I often have Internet connection issues from the computer in the other room. It can find the access point, but not connect to Internet. I reinstalled the WUSB300N driver again, but I still cannot connect.
View 2 Replies View Relatedi am placing a formal request to Cisco and to the firmware development team to create a new-and-improved firmware release for the WET200 wireless Ethernet bridge, a product that is still being produced, shipped, and sold. I purchased the product about one-and-a-half years ago and have enjoyed its performance. There have been, however, some flaws with the device, namely the following:While configured to use WPA2-based security, DHCP-related traffic is not passed from a router/gateway's DHCP Server to connected devices on the WET200. Current firmware release notes indicate this was a known issue and was, supposedly, fixed; however, due to the level of problems customers are reporting, it appears this may have only been resolved, if at all, with security configurations of WPA, WEP, or OPEN. It has not been fixed for customers using WPA2-based security.When I originally purchased the WET200 and configured it to use WPA2-based security, while it, initially, did have a few problems connecting to my router/gateway, it, eventually, did connect and stayed connected for, approximately, one year. However, in September of 2009, it suddenly lost connectivity with my router/gateway and has not been able to establish a connection since, even after reinstalling the latest firmware revision and after several soft and hard resets of the device. I tested the WET200 with another router/gateway, only to experience the same issue. Other devices are connecting to my router/gateway, but, not the WET200. The last firmware update for the WET200 was dated back in July of 2008. Currently, it is January 2010 and since these issues have been known for quite some time, it is unacceptable that the firmware for this device has not been updated in such a long time, especially when there are known issues with the WET200's firmware. Such lack of support is forcing me and my clients to stop using these Cisco-based products and purchase competing hardware, something I would prefer not to do; however, without better support, I and my clients do not have a choice. Expecting me and my clients to use an inferior form of security on the WET200, such as WEP and/or WPA, until a firmware update is issued is unacceptable, especially when that update has not been released in over one-and-a-half years. Such lack of support is especially unforgettable when my clients and I are looking to purchase new networking equipment. In the past, I would not have hesitated to purchase a Cisco-based product; now, with this experience in mind, I am finding it very difficult to recommend to a client that he or she should invest their organization's finances into Cisco-branded equipment. Proper, professional, timely, support of your hardware is expected of your customers, especially if you wish them to remain loyal customers. I have noticed that other similar devices, albeit, higher-end devices, have had their firmware updated, more recently, compared to the WET200. I assumed this meant that the firmware development team was updating all firmware on such devices. So far, I have been disappointed in the lack of firmware updates for the WET200. While I understand the possible desire to update the higher-end products, first, as a professional whose job is to research, recommend, purchase, install,configure, secure, and maintain both the enterprise-level and small business-level devices, I highly encourage Cisco not to overlook their small business products when the firmware development team is updating firmware for any Cisco products. Deficiency in the support of one strata of Cisco-based products is reflective upon the support of any Cisco-based product and is not easily forgiven by Cisco customers, such as myself, when new and additional hardware needs to be purchased.
View 15 Replies View RelatedI'm looking to bring up a wireless bridge between 2 WET200.I've set in Wireless -> Basic Settings and Wireless -> Security the same parameters in both devices, but it fails.
View 13 Replies View Relatedafter reading the many issues reported here about the WET200's WPA abilities (or lack thereof), I doubt that there will be an easy solution to the issue I'm having, but it's worth a try.The setup consists of a WET200 that should bridge two devices in a remote room to our main network. The AP is a WAP4410N, which works beautifully with all other connected devices. The WAP4410N is set up in 'WPA2-Personal Mixed' mode, and only b/g (as n was giving other, unrelated trouble). The WET200 sees the network just fine, is able to connect and receives an IP from the DHCP server. The devices behind the bridge also have connectivity - all well so far. However, at a certain point in time, which i _believe_ to coincide with the key renewal on the AP, the bridge loses the connection to the AP, even though it reports its WLAN status on the web interface (via LAN) as connected. The AP's log shows the following (MAC address is the WLAN interface on the WET200).
View 2 Replies View RelatedI have a new WET200 wireless bridge and cannot authenticate to our WPA2 EAP-TLS freeradius server. Here are the steps that I have taken so far:
1. Renamed my pkcs12 client certificate to .pfx extension and imported it into the WET200.
2. Used the client certificate import password as the "Private Key Password"
3. Typed in the client "Login Name"
The freeradius server recognizes the WET200 with the entered credentials but will not authenticate. The freeradius debug log gives the following error:
WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
WARNING: !! EAP session for state 0x3e833be03884222b... did not finish!
WARNING: !! Please read [URL]
WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Normally, with other wireless devices the CA (ceritificate authority) certificate needs to be installed to the client as well as the pkcs12 client certificate? Is there a way to place a CA and client certificate into the WET200?What is the proper method to install certificates into the WET200 for FreeRadius EPA-TLS authentication?
I just picked up a WET200... connect it wirelessly to a Verizon Mifi so wired devices can get access to the Internet.
I've had zero luck connecting the WET200 to a wireless network...I've tried two different ones and I've also tried changing from WPA to WPA2.
We Have a WLC-4402 controller with LWAPPs and different VLANs and SSIDs. I've configured a Linksys WET200 to associate to one of the SSIDs.On the WLC I can see, that the WET200 is associated to one Wlan.Then I connect one computer with a static IP address and works fine.But when I connect a second one, everythiing goes down. It does not connect.I can only connect one computer to the WET200.Do I need other seetings on the WLC to allow pass traffic through the WET200?
View 4 Replies View RelatedI'm having a problem with a cisco bridge WET200 we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge but the equipment is not communicating with the gateway, with nothing!WLC always appears the following error:
WiSM-slot9-1) >debug client XX:XX:XX:XX:XX:XX
(WiSM-slot9-1) >*apfReceiveTask: May 23 12:03:27.953: XX:XX:XX:XX:XX:XX Deleting mobile on AP XX:XX:XX:XX:XX:XX(0)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Adding mobile on LWAPP AP XX:XX:XX:XX:XX:XX(0)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Association received from mobile on AP XX:XX:XX:XX:XX:XX
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX 0.0.0.0 START (0) Changing ACL 'Guest' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Applying site-specific IPv6 override for station XX:XX:XX:XX:XX:XX - vapId 5, site 'default-group', interface
[code]....
i have test command config network ip-mac-binding disable but It does not connect....when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured?
I'm having a problem with a cisco bridge WET200.we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge [code] but the equipment is not communicating with the gateway, with nothing!
when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured
I'm looking to bring up a wireless bridge between 2 WET200.I've set in Wireless -> Basic Settings and Wireless -> Security the same parameters in both devices, but it fails. [code]
View 6 Replies View RelatedI've got a WET200 connecting to a wireless router (linksys WRT54G) setup thru the WET200 site survey.Does the WET200 need to have an ip with the same sub net as the network the WRT54G is connected to?I have a laptop hooked up the the WET200 with a static IP. I cannot ping IP's of the same sub net on the network the WRT54G is connected to nor see anything on the internet?
WET200 connected to wireless AP WRT54G (192.168.23.3)
WET200 IP address = 192.168.23.8
Laptop IP address = 192.168.23.218 (connected to port 1 of WET200)
I can configure the WET200 via the laptop, but not able to see anything across the bridge?
have netgear pcmcia card need to connect to new belkin wireless access point.
View 1 Replies View RelatedI'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
View 4 Replies View RelatedI have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.
I've been following those instructions to set a dir-615 as a wifi access point connected to a switch : [URL]. I am now able to connect to the 615 either by wifi or by typing it's ip address with another computer connected to the LAN. Connecting to the 615 by wifi, i can do a ping request to urls or receive and send mail with my e-mail client but i can't access websites using my browser.s it possible to get it working without installing some kind of modified firmware? I tried plugging the Internet ethernet cable in the LAN and Internet ports of the 615, none works.
View 3 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
We have recently been given this unusual task. The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition. Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?
Can the access point AP541N connect to wireless clients with 802.11g/a simultaneously?
View 1 Replies View RelatedWe have a 2504 Wireless Controller and it works great!We currently have 6 Access Points (Aironet 1252) connected.We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.Now, I have been assigned to add another Access Point, but at a remote site.The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.We have plenty of licences on our current Wireless Controller.Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
Is 802.11ac wireless module for Cisco Access Point 3602 is available to order ? what Wireless controller we need to use for the support of 802.11ac wireless standard ?802.11ac will support only on 5700 series wireless controller ? Or it will support with 5508 Series also ?
View 7 Replies View Related
