I'm having a problem with a cisco bridge WET200.we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge [code] but the equipment is not communicating with the gateway, with nothing!
when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured
I'm having a problem with a cisco bridge WET200 we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge but the equipment is not communicating with the gateway, with nothing!WLC always appears the following error:
WiSM-slot9-1) >debug client XX:XX:XX:XX:XX:XX
(WiSM-slot9-1) >*apfReceiveTask: May 23 12:03:27.953: XX:XX:XX:XX:XX:XX Deleting mobile on AP XX:XX:XX:XX:XX:XX(0)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Adding mobile on LWAPP AP XX:XX:XX:XX:XX:XX(0)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Association received from mobile on AP XX:XX:XX:XX:XX:XX
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX 0.0.0.0 START (0) Changing ACL 'Guest' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Applying site-specific IPv6 override for station XX:XX:XX:XX:XX:XX - vapId 5, site 'default-group', interface
[code]....
i have test command config network ip-mac-binding disable but It does not connect....when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured?
We Have a WLC-4402 controller with LWAPPs and different VLANs and SSIDs. I've configured a Linksys WET200 to associate to one of the SSIDs.On the WLC I can see, that the WET200 is associated to one Wlan.Then I connect one computer with a static IP address and works fine.But when I connect a second one, everythiing goes down. It does not connect.I can only connect one computer to the WET200.Do I need other seetings on the WLC to allow pass traffic through the WET200?
View 4 Replies View RelatedI just picked up a WET200... connect it wirelessly to a Verizon Mifi so wired devices can get access to the Internet.
I've had zero luck connecting the WET200 to a wireless network...I've tried two different ones and I've also tried changing from WPA to WPA2.
I've just purchased 2 WET200 wireless bridges for our organisation, with the intention of using them to create a wireless bridge between 2 buildings.I've followed this guide here: url...and I'm unable to configure any kind of security other than WEP. More disconcertingly, the foot of that guide states:WET200 only supports WEP for the Wireless Security."Surely this can't be the case? All the marketing blurb states clearly that the WET200 supports WPA2, and I would have thought WPA2 was a given for any wireless product sold today, especially a business grade product. Have I misunderstood what this device can do?
View 4 Replies View RelatedThis is what the Log shows when I try adding a 4404 to NCS
[2012-09-11 12:37:04,199] [ICE Service[ 1]Thread: 7] [inventory] [INFO ] - Complete inventory for deviceid 11020009 at Tue Sep 11 12:37:04 EST 2012. Total time taken to collect inventory in milliseconds = 1304
[2012-09-11 13:48:41,707] [http-443-10] [inventory] [INFO ] - Device with id 11020010 is managed state now, initial inventory collection started
[2012-09-11 13:48:41,768] [http-443-10] [inventory] [INFO ] - Initial inventory collection completed for device with id 11020010 without exception
[2012-09-11 13:48:41,822] [ICE Service[ 1]Thread: 8] [inventory] [INFO ] - Enter collect inventory for deviceid 11020010 at Tue Sep 11 13:48:41 EST 2012
[2012-09-11 13:48:41,960] [ICE Service[ 1]Thread: 8] [inventory] [INFO ] - Called InventoryCollectorEngineXdeImpl.call()for device ID = 11020010.
[2012-09-11 13:48:42,045] [ICE Service[ 1]Thread: 8] [inventory] [INFO ] - Invoking FeatureRunner [returned result: mib2-bootstrap] for MNE collection of device: 11020010)
[2012-09-11 13:48:42,159] [ICE Service[ 1]Thread: 8] [inventory] [ERROR] - 192.168.12.77 No matching device profile found.......
[code]....
We have two controllers 7510 with the same config (SSID, Mobility Groups, etc)... All APs now was joined in wlc01... If we try to one o more APs join to another controller.. it's is not possible and debug show this . [code]
View 1 Replies View Relatedi have currently a 2504 WLC and some 1602i AP's.Basically so far i have configured the WLC as per the guidelines on the startup and now i want to join the AP's (which i haven't managed to do yet) and the setup the wireless network.I can get the AP to join and pickup an ip address and that is it. It comes up with different error messages from the WLC, and through hyper terminal, none of which i understand but the main jist is the following:
*spamApTask4: Feb 19 15:05:56.171: #CAPWAP-3-DECODE_ERR: capwap_ac_sm.c:3844 Error decoding Join request from AP 6c:20:56:0e:23:e0
AND
0Tue Feb 19 15:06:19 2013AP with MAC 6c:20:56:0e:23:e0 (AIR-CAP1602I-E-K9 ) is unknown.
AND
I am facing problem with an outdoor access point AIR-1522-K-E series which is unable to join a wirless lan controller 5508. The wireless AP is able to get IP address from dhcp server and discover the Wireless controller IP address. After this i see following status messeges on the console of AP.
*Aug 27 11:04:19.767: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 27 11:04:21.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.2.64.50 peer_port: 5246
*Aug 27 11:04:21.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Aug 27 11:04:21.707: %CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.2.64.50 peer_port: 5246
[Code]...
I am trying to connect a Zodiac iAqualink wireless pool equipment controller to my home network (WRT54G) without success. This is a 802.11b device. My router is set to mixed mode. What I have tried:
1. Set it up as suggested in the instructions: WEP2 security, double checked SSID and password
2. Set it up without wireless security
3. Changed channels
4. Set mode to 802.11b
In all cases the LED on the iAqualink that is supposed to indicate that it is connected to the network illuminates properly, but I can never find the device using EasyLink Advisor.
I have initially configured 2504 controller with necessary parameters. & we have LAP1131AG access Points. we have connected 2 Nos. of access points in network. we are getting Both AP connected with controller,Whenver i am trying to connect with this wireless network though SSID( currently, open authentication), laptop's not connecting with it. it shown error that " Windows was unable to connect to SSIDname "
View 4 Replies View Relatedthe specified destination is not reachable. connecting error 769
View 2 Replies View RelatedI'm looking to bring up a wireless bridge between 2 WET200.I've set in Wireless -> Basic Settings and Wireless -> Security the same parameters in both devices, but it fails.
View 13 Replies View Relatedafter reading the many issues reported here about the WET200's WPA abilities (or lack thereof), I doubt that there will be an easy solution to the issue I'm having, but it's worth a try.The setup consists of a WET200 that should bridge two devices in a remote room to our main network. The AP is a WAP4410N, which works beautifully with all other connected devices. The WAP4410N is set up in 'WPA2-Personal Mixed' mode, and only b/g (as n was giving other, unrelated trouble). The WET200 sees the network just fine, is able to connect and receives an IP from the DHCP server. The devices behind the bridge also have connectivity - all well so far. However, at a certain point in time, which i _believe_ to coincide with the key renewal on the AP, the bridge loses the connection to the AP, even though it reports its WLAN status on the web interface (via LAN) as connected. The AP's log shows the following (MAC address is the WLAN interface on the WET200).
View 2 Replies View RelatedI have a new WET200 wireless bridge and cannot authenticate to our WPA2 EAP-TLS freeradius server. Here are the steps that I have taken so far:
1. Renamed my pkcs12 client certificate to .pfx extension and imported it into the WET200.
2. Used the client certificate import password as the "Private Key Password"
3. Typed in the client "Login Name"
The freeradius server recognizes the WET200 with the entered credentials but will not authenticate. The freeradius debug log gives the following error:
WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
WARNING: !! EAP session for state 0x3e833be03884222b... did not finish!
WARNING: !! Please read [URL]
WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Normally, with other wireless devices the CA (ceritificate authority) certificate needs to be installed to the client as well as the pkcs12 client certificate? Is there a way to place a CA and client certificate into the WET200?What is the proper method to install certificates into the WET200 for FreeRadius EPA-TLS authentication?
I just purchased a WET200 wireless bridge. After trying a very long password for an enterprise certificate the bridge restarted and I have not been able to contact the device with the default 192.168.1.226 ip address. I have tried performing a reset even by holding the reset button in for a minute. The bridge will not ping either. I do have a power light and the wireless light flashes and the Ethernet port lights function when plugged into my laptop.
View 3 Replies View RelatedIf I'm outside my home network, I'm getting an error saying router is offline when i use the iPhone smart wifi app on my cellphone service LTE.When I connect using my home connection or wifi, I don't get the error and I'm able to connect to my router E3500.Why is this happening ?
View 7 Replies View RelatedI've got a WET200 connecting to a wireless router (linksys WRT54G) setup thru the WET200 site survey.Does the WET200 need to have an ip with the same sub net as the network the WRT54G is connected to?I have a laptop hooked up the the WET200 with a static IP. I cannot ping IP's of the same sub net on the network the WRT54G is connected to nor see anything on the internet?
WET200 connected to wireless AP WRT54G (192.168.23.3)
WET200 IP address = 192.168.23.8
Laptop IP address = 192.168.23.218 (connected to port 1 of WET200)
I can configure the WET200 via the laptop, but not able to see anything across the bridge?
My roommate has just gotten a second hand laptop and he's trying to connect it to the Wireless network so that he can browse the internet from his room.However, although all the settings are correct, attempting to connect to the network loops.It comes up showing the Wireless Networks available, I select the network and click connect, it then asks for the encryption key. I enter the key and hit connect again, it comes up with the 'Connecting' pop-up and then loops back to the Available Networks screen again.There are no error messages, it just goes back to the starting screen and it hasnt connected.The Laptop in question is a Lenovo T60 with a Intel PRO/Wireless 3945ABG card.The router is a TP-Link TD-W8960N.
View 5 Replies View Relatedi am placing a formal request to Cisco and to the firmware development team to create a new-and-improved firmware release for the WET200 wireless Ethernet bridge, a product that is still being produced, shipped, and sold. I purchased the product about one-and-a-half years ago and have enjoyed its performance. There have been, however, some flaws with the device, namely the following:While configured to use WPA2-based security, DHCP-related traffic is not passed from a router/gateway's DHCP Server to connected devices on the WET200. Current firmware release notes indicate this was a known issue and was, supposedly, fixed; however, due to the level of problems customers are reporting, it appears this may have only been resolved, if at all, with security configurations of WPA, WEP, or OPEN. It has not been fixed for customers using WPA2-based security.When I originally purchased the WET200 and configured it to use WPA2-based security, while it, initially, did have a few problems connecting to my router/gateway, it, eventually, did connect and stayed connected for, approximately, one year. However, in September of 2009, it suddenly lost connectivity with my router/gateway and has not been able to establish a connection since, even after reinstalling the latest firmware revision and after several soft and hard resets of the device. I tested the WET200 with another router/gateway, only to experience the same issue. Other devices are connecting to my router/gateway, but, not the WET200. The last firmware update for the WET200 was dated back in July of 2008. Currently, it is January 2010 and since these issues have been known for quite some time, it is unacceptable that the firmware for this device has not been updated in such a long time, especially when there are known issues with the WET200's firmware. Such lack of support is forcing me and my clients to stop using these Cisco-based products and purchase competing hardware, something I would prefer not to do; however, without better support, I and my clients do not have a choice. Expecting me and my clients to use an inferior form of security on the WET200, such as WEP and/or WPA, until a firmware update is issued is unacceptable, especially when that update has not been released in over one-and-a-half years. Such lack of support is especially unforgettable when my clients and I are looking to purchase new networking equipment. In the past, I would not have hesitated to purchase a Cisco-based product; now, with this experience in mind, I am finding it very difficult to recommend to a client that he or she should invest their organization's finances into Cisco-branded equipment. Proper, professional, timely, support of your hardware is expected of your customers, especially if you wish them to remain loyal customers. I have noticed that other similar devices, albeit, higher-end devices, have had their firmware updated, more recently, compared to the WET200. I assumed this meant that the firmware development team was updating all firmware on such devices. So far, I have been disappointed in the lack of firmware updates for the WET200. While I understand the possible desire to update the higher-end products, first, as a professional whose job is to research, recommend, purchase, install,configure, secure, and maintain both the enterprise-level and small business-level devices, I highly encourage Cisco not to overlook their small business products when the firmware development team is updating firmware for any Cisco products. Deficiency in the support of one strata of Cisco-based products is reflective upon the support of any Cisco-based product and is not easily forgiven by Cisco customers, such as myself, when new and additional hardware needs to be purchased.
View 15 Replies View RelatedI have one WET200 Wireless Brigde, connected to internet router... I can't use the infraestructure mode to broadcast the ssid to wireless cliente like laptops,
Only can use the ad hoc mode, but the wireless clients dont reach the internet from adhoc connection trought WET200...The datasheet saids "client only" for WET200, what is the diference between client only and Access Point mode? ??
My xp computers recently gave up. So, I bought a new one (windows 7).
When I had my new computer plugged directly into my modem, there was no problem; I could easily connect to the internet.Yet, when I plugged the modem into my router (WRT54GS) and then plugged the router into the computer, I repeatedly encountered: Error 651.
The new computer has a built-in wireless adapter. So, I was able to disconnect the router and try to re-connect via a wireless connection. Yet, dispite being able to connect to my "network", the computer was not able to connect to the internet; again, I received the dreaded Error 651 message.I tried using the installation disk, but it would not work, either.
I have a cisco router 2951 and this is the message that apear on the console:
ERROR: DDR controller 1 data training time out during initialization! Stop.
What does it mean?
I'm looking to bring up a wireless bridge between 2 WET200.I've set in Wireless -> Basic Settings and Wireless -> Security the same parameters in both devices, but it fails. [code]
View 6 Replies View RelatedI'm starting to see an error creep up that I havn't seen since 2003/2004 on my brand new 5508 controllers. I'm recieving the following from my WCS: Receive Multicast Queue is full on Controller and then on the controller itself RX Multicast Queue Full. I understand this used to be due to a large influx of ARP requests or CDP packets on older controllers but, this was supposed to be fixed in an update many years ago.
Has seen this on their 5508's. These were advertised as having the horsepower to handle our user loads which arn't really that high at 300 users at any given time max.
so i can not connect to net on my desktop but my wifi works fine, the error is the realtek PCIe FE family controller (code 31) i have tried updating the drivers but nothing i have verizion fios.
View 2 Replies View RelatedI have an 5510 ASA with 804 IOS. In that installed anyconnect (anyconnect-win-2.0.0343-k9.pkg) version. But when i am going to connect it from https:// I am getting the below error. So as a work around i tried to install anyconnect-win-2.5.6005-pre-deploy-k9.msi at my laptop and try to connect from https:// i am able to connect.
View 4 Replies View Relatedtying to connect CSM client to CSM server (ver 4.0) and getting attached error message. The server is running, no errors reported while installation, all services are up and fine. I tried to install client locally on the server and connect it that way with no luck. CSM server runs on Win 2008, firewall disabled.
View 0 Replies View RelatedI am unable to connect to the vpn I set up on my ASA 5505 using the Cisco VPN Client on a Windows machine. The log of the vpn client and the config of the ASA 5505 are below.
LOG CISCO VPN CLIENT
Cisco Systems VPN Client Version 5.0.06.0160
Copyright (C) 1998-2009 Cisco Systems, Inc. All Rights Reserved.
[Code]......
my net is connecting so late after a sudden hang in windows, and sometimes showing Error 718..It has become very often...I asked my friends (same connection), they are not having any problem from the ISP... what's wrong? :/ Few minutes ago, it was showing error 718, i had to restart, and then it connected (still slowly).
Core2Duo, Dg41Rq, @2.93Ghz, 2Gb DDR2, 500Gb HD, avast free, Ethernet connection braodband PPPoE via landline.
I had been working on our client servers through Cisco VPN using internet datacard. But from past 3 weeks after logging into Cisco VPN using my username/password, when I try to connect to any of the servers, it is giving connection timed out error.
Whereas, my team members across other locations are able to connect to the servers using my VPN username/password.
I thought there might be some issue with my laptop or internet datacard. I got my laptop formatted, even tried out with fresh new laptops & new internet datacards, but the issue remains same.
I have tried using vpn_5.0.06.0160-k9 & vpnclient-5.0.05.0290-k9 to connect but issue did not get resolved.
I have a Linksys WRVA4400N router in my home office that I access my internet with throughout my house. I also have a Linksys WET200 Bridge that I want to use but can’t get them configured together. The Tech support folks keep shifting me back and forth and I’m about the throw my hands in the air. I get to the Advance Configuration setup for the WET200 and when I place the configuration URL 192.168.1.226 I get nothing. I can get to my router adjustments just unsure how to get the WET200 setting entered.
View 1 Replies View Relatedi got an error while connecting to my PIX (515e) via ssh connection there is an error message appears (The server has disconnected with error, server message reads: Internal Error) and at the console session at the time time, the following message appears also (process_create: out of memory)
View 1 Replies View Related