If I'm outside my home network, I'm getting an error saying router is offline when i use the iPhone smart wifi app on my cellphone service LTE.When I connect using my home connection or wifi, I don't get the error and I'm able to connect to my router E3500.Why is this happening ?
View 7 Repliessince my network (static ip, cameras, and other boxes) is set up using 10.0.0.xx. How do I change the default ip address on the Linksys e3500 wifi router to 10.0.0.xx?
View 2 Replies View RelatedI don't see it in the menu as it was in the classic firmware. does that mean i cannot forward specific port to open a port in Transmission on a mac?
this is the only thing i see - but what i entered does not work - port is still closed.
i've a bit more complicated setup:
main house - comcast modem and wifi router <--------> guest house - WIFI bridge - ethernet cable to a WIFI router - my apple laptop. WIFI bridge is ASUS with DD-WRT firmware. i get good speed up to 20mbps/4mbps (down/up)
transmission works, but the port is closed ? doe it really matter ? what can i do to open the port (for e. "61622") ?
I've tried all sorts of settings, and I'm still holding out that its a setting possibly, but I have a E3500 and devices on both 5Ghz and 2.4Ghz... Most of them, probably when idle, seem to stop working over WIfi. They still have decent connection, but every internet related request just times out. Disable and reinable the wifi and it works great again.
Could this be defective wifi radios? or could it really be interference? I have it happening on multiple devices. Also, I'm not far away from the router when it occurs, and when I reconnect, it seems to work just fine for a while. Basically the big problem is on the cell phones and tablets because I'll miss notifications... I'll turn off the wifi and turn it back on when I use the device next, then a flood of notifications will come in. Again, it's not just a phone thing, tablets and laptops have the same problem, that's just the main reason I want it fixed.
I have a router (Linksys E3500) set up as an AP. To do that I just disabled DHCP on the router. I can connect devices to it fine, but I'm having a couple of issues.
So I have a DC setup. It's in the same subnet as the router and I can ping it fine, but when I browse to the AP for management it prompts with the username/password and won't accept the credentials. Not sure what's going on here as I've always used the same credentials and I logged into the router fine when I was first setting it up.
Another issue, is if I try to ping this router from a different subnet, it fails. I can ping the DC fine from this subnet. Would this be to do with the AP just acting as a pass-through?
My xp computers recently gave up. So, I bought a new one (windows 7).
When I had my new computer plugged directly into my modem, there was no problem; I could easily connect to the internet.Yet, when I plugged the modem into my router (WRT54GS) and then plugged the router into the computer, I repeatedly encountered: Error 651.
The new computer has a built-in wireless adapter. So, I was able to disconnect the router and try to re-connect via a wireless connection. Yet, dispite being able to connect to my "network", the computer was not able to connect to the internet; again, I received the dreaded Error 651 message.I tried using the installation disk, but it would not work, either.
I've got a Linksys E2000 router and a Brother MFC-7840W wireless printer and they don't seem to want to play nice together. The set-up process was fine and I can usually print wireless without a problem, but every so often I'll try to print and my computer will say that the printer is offline. Other computers on my network also show it as offline. The printer confirms it has an IP address, but even after power cycling it won't be picked up by my machines. I've even tried a full reset of the printer and re-configured it, at which point it is able to successfully obtain an IP address, but it still shows as offline on my PCs.
The only solution I have found is to powercycle the router. This always works. Now that's not a terribly inconvenient workaround most of the time, so I've been doing that for a few months now. It obviously implicates the router as the point of failure, but wireless internet access is not affected when the printer appears to be offline, so obviously some packets are getting through normally.
I recently buoght a E3500 router for my home. I want to add my old WRT610n as a repeater bridge in my basement. The 610n has been flashed - whenever i try to get it going - WIRELESSLY - i get IP conflicts on the 2 laptops that we have.
View 1 Replies View RelatedHave a Belkin F6D4230-4 Version 3, both times we have stayed here we have noticed the same issue, we can connect to the router, but after a while it throws everything offline, and then you will see the orange light on the front of the router flashing. I usually have to reboot the router to get it to come back online. I did check the firmware version and it is the latest version 3.0 something, but it did say it was the latest?
View 14 Replies View Relatedthe specified destination is not reachable. connecting error 769
View 2 Replies View RelatedMy Linksys WRT120N router was working fine for all of 1 and 1/2 months and suddenly it stopped making the internet connection. At first nothing could access the internet but now that I've reset the router (via the little reset button in the back) my Kindle can access the wireless, but of course no password etc. I actually don't know how to put back the username and password for it. When router is connected: When I troubleshoot the connection by clicking on "Repair Connection" it takes about 2-5 mins "obtaining a new network address" then I get an error saying "The wired connection to your router was not automatically repaired. X Local network: Not connected.
View 14 Replies View RelatedI'm having a problem with a cisco bridge WET200 we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge but the equipment is not communicating with the gateway, with nothing!WLC always appears the following error:
WiSM-slot9-1) >debug client XX:XX:XX:XX:XX:XX
(WiSM-slot9-1) >*apfReceiveTask: May 23 12:03:27.953: XX:XX:XX:XX:XX:XX Deleting mobile on AP XX:XX:XX:XX:XX:XX(0)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Adding mobile on LWAPP AP XX:XX:XX:XX:XX:XX(0)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Association received from mobile on AP XX:XX:XX:XX:XX:XX
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX 0.0.0.0 START (0) Changing ACL 'Guest' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Applying site-specific IPv6 override for station XX:XX:XX:XX:XX:XX - vapId 5, site 'default-group', interface
[code]....
i have test command config network ip-mac-binding disable but It does not connect....when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured?
I'm having a problem with a cisco bridge WET200.we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge [code] but the equipment is not communicating with the gateway, with nothing!
when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured
I have a BEFCMU10 v1 that has been misbehaving recently. It will go off line losing contact with the router and the Internet. It will stay off line for 8 to 10 minutes and then comeback on its own. If I cycle the power it will come up pretty quickly. Here is a log of a recent episode without power interruption.; [URL] Is there a solution or is it time for a new modem?
View 9 Replies View RelatedMy roommate has just gotten a second hand laptop and he's trying to connect it to the Wireless network so that he can browse the internet from his room.However, although all the settings are correct, attempting to connect to the network loops.It comes up showing the Wireless Networks available, I select the network and click connect, it then asks for the encryption key. I enter the key and hit connect again, it comes up with the 'Connecting' pop-up and then loops back to the Available Networks screen again.There are no error messages, it just goes back to the starting screen and it hasnt connected.The Laptop in question is a Lenovo T60 with a Intel PRO/Wireless 3945ABG card.The router is a TP-Link TD-W8960N.
View 5 Replies View RelatedTrying to login to my router with the default IP address of http://192.168.1.1
Been working fine forever.. I went in and dumped all my cache on my browers IE and Firefox.
Still getting this error. I have unplugged the router and cable model and also restarted the computer.
This seems to be a recent issue since it was working a few days ago..
I added a VOIP fax line to my network and in doing so, was forced to reset my router, as it would not go on-line. Now the printers are all off line and I can not get them back online. I followed instructions within admin and it did not work. My network is a 2 computer network. My computer acts as server and then one other computer.
View 2 Replies View Relatedthe camera is about 30 feet from the router. Is it too far for the camera to be detected? After I mounted the camera at the front door, after connecting the camera to the electric power, I saw clearly the picture. But after I finished mounting, I could not see the picture anymore. On the computer, it was stated that the camera was offline.
View 1 Replies View RelatedI've got an apple Airport Express and have managed to set it into my network. Airplay works on both Itunes and my phone. However after 10-15minutes the Airplay drops out and the network map shows that the airport express is 'offline'. however the airport express LED remains showing it still have connection to the network. The only way to get it back is to reset the AE. The apple forum has lots of people stating the same problem with WAG120n routers.
-Router Firmware V 1.00.16
-Airport Express firmware version 7.6.1
-windows Vista
I have an E3000 with firmware v. 1.0.01 build 6. I am trying to upgrade to the latest firmware version. I downloaded the file, and when I went to install from the web page I got the error message: Not enough memory available. I tried from 2 computers and got the same message.
View 6 Replies View RelatedI've just recently started to get this error, and I'm not sure why (I have no expierence with routers whatsoever). I have noticed, that whenever this happens though, that my NAT type for my xbox goes strict.
View 4 Replies View RelatedI have a problem with my router, WRT54G2. I was upgrading my firmware when my computer froze up, so I had to exit. Afterwards, I could not connect to the web based setup page anymore. I did a factory reset and installed it again with Network Magic and set up my wireless key. It is working now however, I cannot get into the web based setup page. Whenever i go to 192.168.1.1 and enter my info, it just says 500 Internal Server Error. I was always able to access this page, now I can't, so I assume it's not working because of the interrupted firmware update. I do alot of mac filtering and I limit the amount of IP addresses my router gives out so if anyone hacks my security key, they still won't be able to connect, so accessing my router setup page is important to me. I have reset (hold down reset button for 30 secs - 1 minute) the router many times and still nothing. I mean, the router still works. My brother and I can still connect with our laptops, I just can't get to the web based setup page.
View 7 Replies View RelatedCouple weeks ago installed my ea3500. Am loving its ease of use and features. I also created a smart wifi account. yesterday I tried to remotely log in and got password errors. I have tried all my small arsenal of staple passwords. No go. Today I called Linksys for support. After getting transferred around then having to explain the difference between router local and online passwords, the customer service rep had me create a new account telling me I had not previously done so. Also said if I had, then I wouldnt be able to create another since a router can only have one account associated with it. What the heck, worth a try.
Now, when I try to log in to the web based settings I get 'Unexpected Error 2120.' If i try to log in from my SmartWifi iphone app I get 'No associated networks. the linksys smart wifi account specified does not have associated networks.'
Just to clarify, I can log in locally to the router, but cannot via my smartwifi account.
I am treating to install a router e 1000 when I run the CD setup a get an error code 82bd0305
View 7 Replies View RelatedI bought a new CISCO EA6500. During, first setting up, error was occurred. And, I cannot do anything with this product. How can I setup this one?
Error code: 0x82BF0306
Error description: A JNAP call to the device failed for an unknown reason.
Model name: EA6500
Model description: unknown
Serial number: unknown
Firmware version: unknown
Operating system: Mac OS X 10.8.3
Software version: 2.0.12254.2
Connection type (WAN): unknown
IP address (LAN): unknown
IP address (WAN): unknown
Computer IP address: unknown
I get error 2123 whaen I try to access the Security tab. Also, all my port range forwarding settings are gone, and it will not let me enter any new port forwarding settings.
View 6 Replies View RelatedI have been experiencing problems with my Linksys EA4500 router not being able to find my network. I reset the router and it was able to find my network, but said it was out of range despite it not being so.
View 1 Replies View RelatedI am installing the router but keep getting stuck on the 4th step and getting an error code 321. i currently have cable internet, which is working but when i follow the instructions it wont work. I cant access 192.168.1.1. I tried through google chrome and internet explorer but neither will recognize it. I just started school and would like to use wireless internet on my new laptop instead of cable on my desktop.
View 9 Replies View RelatedI had a E1200, I read the articles from the support about the routers, I think the "access Restrictions" has more flexible to setup on for the parental control, after chated to cisco support person online, I was told that the E1200 v2 has this "access restrictions" function, and I wan convinced to purchase from them. I did. I got the E1200 v2 recently, however, after I installed the CD and found there is no "access restrictions" tab, instead the "access policy" is still there. by the way the firmware is 2.0.02 now. How to get the "access restrictions" from setup? I've chatted with cisco support person twice again, but nobody can fix the problem, one suggested to restart and reinstall the CD. I uninstalled the software, restarted the computer and reinstalled the CD. same problem, no tab of "access restrictions".
View 6 Replies View RelatedNotified of new firmware for my router. Tried to install. Downloaded fine but will not install. Keeps saying error but not what kind, how to fix, not anything.
View 1 Replies View RelatedI recently purchased a new router (WRT54G Ver.6) and the initial setup went well. however, when I try to connect my xbox 360 to this network, the DNS does not resolve and it fails every time. what should I do?
View 2 Replies View RelatedI am trying to set up a E2500 router to a Arris/Comcast modem. I connected the blue cable to the router then to the modem and followed the Cisco instructions on the disk. I was 90% done when I received a error message 82BD0118 - Description - adapter connection time out period expired with no IP address.
View 2 Replies View RelatedI tried to connect to my E1550 router admin page at 192.168.1.1 and I'm not seeing the login page. I'm getting an error. I've always been able to get to the admin page. I'm not sure what changed. I tried changing the IP# and subnet mask of my laptop and I still can't connect. I tried resetting the router to factory defaults.
View 1 Replies View Related