Trying to login to my router with the default IP address of http://192.168.1.1
Been working fine forever.. I went in and dumped all my cache on my browers IE and Firefox.
Still getting this error. I have unplugged the router and cable model and also restarted the computer.
This seems to be a recent issue since it was working a few days ago..
I can't log into the router. Get 502 Bad Gateway - Model EA4500; Have a USB Drive connected to the router.
Power-off and Powered-Back on - no change.
I have been experiencing problems with my Linksys EA4500 router not being able to find my network. I reset the router and it was able to find my network, but said it was out of range despite it not being so.
View 1 Replies View RelatedI have the tunnel set up, but when I try to renew and release it pops up with this error.
View 9 Replies View RelatedThere are several features that don't work and are returning errors. For starters, when trying to save settings for media/device prioritization I am receiving a 2123 error message. Unable to save settings. EA4500/N900 Router, Cisco Cloud Connect.
View 3 Replies View RelatedI have upgraded the firmware on my Linksys BEFSR41 V4.3 router. On this router i used Statis IP (so DHCP enabled). This worked fine on my network, until this upgrade. Now when i try to ad another static IP , or when i want to change something in the Routing-tab, i get this message ' Wrong Gateway Input! It should be the same subnet with WAN IP'. Strange because i haven't changed anything in the settings.I already did a complete reset on the router, still the same problem.
View 7 Replies View RelatedI recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies View Relatedwe do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies View RelatedI have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies View RelatedI have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
I've looked all over the internet for this and can't find a definate answer. Waited for live chat and got kicked before I got to talk to someone... Just sold my computer and the plan was to buy a newer mac but we've been getting along fine without a computer with just using our iphones. So my question, I see that Cisco has the Connect Express app for the iphone, and I've read about all the features it has like changing settings, router features, etc. But I can't find anything on using the app for the initial set up of the router. I'm currently on an older linksys router (set up before we sold the computer) but it's time for a needed upgrade.
View 3 Replies View RelatedI got my ea4500 all set up. never had a media servor or anything like that, figured this would be an easier way. when i hook up my exteral i can find it but i can only view the files in windows media player. how can i just browse the folders manually? WMP doesnt let me browse the folders as they actually are on the HDD which is such a pain in the **bleep**.
shows a device in "network infrastructure" but it says problem sending command to the program when i click that. i dont want to have to view the HDD in WMP as a media device...
My new EA4500 (fw ver 2.0.36) won't obtain an IP from a Brighthouse TM502G cable modem. The EA4500 replaced a functioning WRT54G which would obtain an IP from the ISP. I've tried upgrading firmware and have used both straight-through and crossover cables between the EA4500 & TM502G to no avail. The EA4500 would issue IPs to it's clients, but not obtain one from it's TM502G. At the moment, all 3 are daisy-chained together with the old WRT54G in the middle in order to make the EA4500 work. Both WiFi and LAN ports function in this configuration.
View 1 Replies View RelatedI downloaded and installed inSSider for Windows and, under the 2.4 Ghz tab, I can clearly see the Router SSID, on Channel 6, exactly as configuredbin the Router. However on the 5 Ghz tab, nothing? I can see Channels 36, 40, 44, 48, 52 and so on BUT no trace of any wireless signal here?I carefully reviewed the wireless settings options and it is indeed enabled.
View 1 Replies View RelatedConnect my primary router EA4500 to another EA4500?
I tried and followed the steps provided here but it doesn't work at all for the Xth time already.
The first router installed and ran flawlessly in minutes. The second one has failed to work in bridge mode for 3 hours now.
Can we get a forum title just for the EA4500?
View 1 Replies View RelatedIn my apartment, I can receive the wireless signal of free scholl wireless, which is accessable without user name and password. Although the signal is not good, but we used to use a router EA3000 to relay the signal. Now my roommate is leaving with this this router. So I bought EA4500 and try to do the similar job. However, I find that the configurations on 192.168.1.1 are different between EA3000 and EA4500. Many options cannot be found in the EA4500 page, such as the wireless client.
View 4 Replies View RelatedI recently got an EA4500 from a friend and when I tried to run the Cisco Connect CD on my MacBook it gets to 25% and then stops and says it can't find a router. I've reset, powercycled, unplugged, plugged, searched, and searched but I cant seem to get it to find the router.
View 3 Replies View RelatedI'm hoping to get this router to allow WOL (actually wake on WAN) but it seems to be blocking the necessary broadcast magic packet even though the settings appear correct. It's not critical, but the reason is this: I'd like to shut down the home PC, but when necessary be able to start it up and use a VPN to access any info I need remotely.
From within the LAN, I can verity that WOL works. I have NIC and PCI WOL enabled in the BIOS. The NIC (a Marvel Yukon Gigabit) has WOL enabled as well as "allow this device to wake.." using magic packets under power management. The target machine's local IP is reserved through the EA4500 DHCP Reservation table. Just for troubleshooting, I opened port 9 in windows firewall. More importantly, I have ports 7-9 forwarded to my target LAN address. Single port forwarding... it just has been less reliable (?). I'm using a mask of 255.255.255.128 in order to enable broadcasting on .127 at some point as it seems it must be necessary. Broadcasting on .255 is not possible, despite some workarounds I found on the web. EA4500 firmware is the latest, 2.0.37. I have turned off the multicast filter and the anonymous internet filters under the security tab.
So, with these settings, I can WOL from inside the network no problem either targeting the LAN address, or by using a dyndns address. So far so good.With these same settings, I can go to WAN using Depicus or the Cloud Connect Pro app over 4G on an iPad. With all these same settings, WOLsniffer confirms the magic packet still getting through over WAN (obviously using the dyndns address). Even better, I can shutdown the target PC and STILL wake it up within a few minutes from WAN. Let me restate that! Wake up over WAN works, but only for the first few minutes after a shutdown.
However, if I wait 20 minutes or so, WOL stops working. If I change the port forwarding to .127, not only does it not work, but WOLsniffer will fail to see the magic packet. My conclusion is that the ARP table is getting purged, which is undertandable, and so the target LAN address isn't in memory. However, frustratingly the EA4500 will not broadcast no matter what settings you use. This limitation is undocumented, and counterintuitive since the software allows you to disable multicast filtering and does not notify you of an error when forwarding to xxx.xxx.xxx.127 with a 255.255.255.128 mask.
How do I enable WDS on my new EA4500 ?
View 3 Replies View RelatedWas thinking to buy this router but I am not sure if it supports magic packets in order to use wake on lan on PCss and NAS
View 3 Replies View RelatedI really want to have a password on my wifi, but I cant control it when all it keeps asking me is for a CD I have a EA4500
View 1 Replies View RelatedUsing the FTP server built into the EA4500 firmware. I can get the FTP service to work from some computers outside my home network, but when i try to access the service from a PC within my home network i am unable to connect to the server through the WAN address.
View 1 Replies View RelatedI bought 2 weeks ago a Linksys EA4500 after searching the best Wi-Fi Router all over the net... I choose this cos all over people writed that it was amazing, fast a nd very good coverage all over the house.
Before I had a Buffalo AirStation Dual Band, wich worked perfectly. But since I have several tv and a central NAS whit all films in MKV, I wanted the BEST product for my system, so I choosed Linksys EA4500!
Well, the result is that (when it works it is greate) but sometimes it disconnects and I have to restart it... And second thing that makes me MAD is that the coverage in my house is WORST!! Before my Wi-Fi was present in all the house, now in some parts doesn't work! The position is the exact same of the Buffalo, so it's not a problem of position... I tryed also a router of 40€ and it has a better coverage! How come? how is it possible that a person pays more than 200$ (in Italy it costs 185€) and the result is so BAD??? I'm totaly freak about Linksys now.
I'm in the process of wanting to upgrade my wireless network but I'm not really agreeing to the Cloud Connect, I don't need to have my settings on the internet. I want to manage everything on my own. I've found the following link on the community to be able to put the classic firmware before the cloud connect feature {URL}.
My question now is : If I buy a brand new EA4500, will it still be possible to downgrade to that firmware? No problem with this one? I'm hoping Cisco will continue to publish bug fixing if any to this classic firmware.
I purchased a EA4500 and at first I could connect to it through its default ciscoxxxxx ssid on my laptop which is 2.4GHz only. I upgraded the firmware using the PC utility and now I can't find the 2.4GHz SSID no matter what settings I do. I've disabled and enabled it multiple times, changed it to have no security or with security and enabled and disabled it and renabled it. Nothing seems to work, but for some reason the 5GHz side I can connect to using a 5GHz device. I've also tried disabling the 5GHz side, but still no 2.4GHz.
View 4 Replies View RelatedJust purchased a ea4500 router. Have setup multiple computers/devices already and works great. This computer (HP dv6000 running Win Vista home prem) however will not connect to the internet. It states that it is connected to the router (computer sees router), using the cloud connect app on my iphone i can see this computer, but will not allow access to the internet (local connection only). It works fine with the wired connection. When attempting to use the cloud connect software, it says it was unable to complete the install. Have attempted trying while connected by wire as well, same result. Have deleted the wireless connection and allowed software to find connection, still same result, cannot install. Wireless worked perfectly with previous router (WRT54G) three days ago.
View 6 Replies View RelatedI have a new EA4500 router and I cannot configure it to reach the 450 mbps that is supposed to get.
I have it configured as follows:
Dual Band- 2,4 and 5 GHz
2,4 in 20MHz only - 5 GHz in 40 MHz only
2,4 Mixed - 5 Ghz only N
WPA2 personal in both
Channel - automatic (both)
I have checked that the 5 Ghz network can only use 4 channels: 36, 40, 44, 48. Where are the channels up to 100 (or more)? How to get all the power of the router?
I just installed a new EA4500 and the range is terrible. How can I increase it?
View 1 Replies View RelatedI had a WRT54G2 router and began having trouble with my PS3. It would connect for a few minutes then it would lose the internet connection. I thought maybe it was the router so I have the EA4500 now. The same problem is still happening. I connected all of my other wireless devices to the EA4500 with no problems. The PS3 connects and signs me in and then two or three minutes I'm disconnected. I called Sony and Cisco for assistance but in vain. The PS3 is showing my network has nearly 100% signal strength so that isn't a problem
View 4 Replies View Related