Linksys Wired Router :: RV0XX Gateway To Gateway VPN?

Mar 6, 2011

I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet. 
 
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
 
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup

View 1 Replies


ADVERTISEMENT

Linksys Wired Router :: RV082 Gateway To Gateway VPN Not Connecting?

Jan 24, 2012

I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.

Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask :  Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256  AES-128 IPSec Setup3DES  Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:

[code].....

View 1 Replies View Related

Linksys Wired Router :: VPN Gateway To Gateway With Two RV042 Constantly

Jul 11, 2012

My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]

View 1 Replies View Related

Linksys Wired Router :: RV042 Gateway To Gateway Connection?

Feb 8, 2011

we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?

View 1 Replies View Related

Linksys Wired Router :: RV042 - Gateway To Gateway VPN Connection

Mar 22, 2011

I have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
 
I cannot ping the computers with static ip configuration.
 
In local an remote computers who have DHCP ip configuration i can ping each other .

View 1 Replies View Related

Linksys Wired Router :: RV082 Gateway 2 Gateway VPN Can't Ping

Jul 26, 2012

We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network.  I am unable to ping between routers, let alone ping computers behind those routers. 
 
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic.  I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
 
To me it seems like a firewall issue at branch 2, but what's causing this.  Also they are currently running 2 differnet firmware version not sure if this would cause a problem.

View 1 Replies View Related

Linksys Wired Router :: RV042 / Setup A Vpn Gateway To Gateway

Apr 6, 2013

i am trying to setup a vpn Gateway To Gateway  when i setup the vpn i can ping  the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?

View 1 Replies View Related

Linksys Wired Router :: RV082 Gateway Shows No Loss On Packet

Mar 25, 2011

I have RV082 in many locations and it is working fine.One location I just starting to have problem with packet lose (50 to 60 %)I ping between two location which i am having problem.Gateway to Gateway shows no lose on packet (reply with 20ms avg.)but router to router will lose packet 50 to 60 %.

View 1 Replies View Related

Linksys Wired Router :: RV042 - Can't Access Internet Or Ping Gateway

Jan 4, 2011

I am using the default configuration at this point.  I just connected 1 computer using the default IP with DHCP on the RV042 router. 192.168.1.0/255.255.255.0.I connect my wildblue satalite modem using a static IP address 75.106.203.xxx / 255.255.252.0 I can ping the RV042 router and the static IP address of the wildblue router but I can't ping the gateway on the wildblue side.  Either from the PC or the Router diag tools.

View 1 Replies View Related

Linksys Wired Router :: Can't Set RV016 To Assign A Default Gateway IP Of Server

Jun 22, 2011

I am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)

View 1 Replies View Related

Linksys Wired Router :: Using RV042 As Layer 3 Clear Gateway For Comcast EDI?

Feb 7, 2013

Comcast installed a new fiber 10M EDI internet connection in our facility the other day and found out it is our responsibility to provide a layer 3 gateway to map the internet connection to the 14 public IP addresses they assigned to us.  We are using RV042 for our existing networks with a T1 we had.
 
Will the RV042 provide the gateway function to route the single IP address comcast provided to the 15 public IP addresses?  If so , can you provide the configuration example on this process?
 
Comcast EDI Connection ---> ???????? ----> 14 Static External Addresses 
 
Interconnect Block 51.235.227.60 / 255.255.255.252.Comcast Gateway is 51.235.227.61Clear Layer 3 device WAN interface: 51.235.227.62Usable IP Block 51.235.227.96/28Mask: 255.255.255.240Usable Addresses: 51.235.227.97 - 51.235.227.110

View 1 Replies View Related

Linksys Wired Router :: BEFSR41 V4.3 / Error - Wrong Gateway Input After Firmware Upgraded

Aug 14, 2011

I have upgraded the firmware on my Linksys BEFSR41 V4.3 router. On this router i used Statis IP (so DHCP enabled). This worked fine on my network, until this upgrade. Now when i try to ad another static IP , or when i want to change something in the Routing-tab, i get this message ' Wrong Gateway Input! It should be the same subnet with WAN IP'. Strange because i haven't changed anything in the settings.I already did a complete reset on the router, still the same problem.

View 7 Replies View Related

Linksys Wired Router :: Should Set RV042 Up As Gateway Or As Router

Aug 8, 2011

I am setting up an RV042 for my small business office and I am trying understand how it needs to be configured.
 
-For WAN1 I have a Wildblue Satellite Modem connected IP 70.66.93.4

-For WAN2 I have a Cradlepoint CTR35 Router with a verizon AirCard Connected IP 192.168.0.1
 
(Verizon has a 5GB download limit and wildblue has a 17GB download limit but it drops out in poor weather)The LAN is IP 172.16.0.1 Subnet Mask 255.255. 255. 0Should I set the RV042 up as a gateway or as a router? 

View 1 Replies View Related

Cisco :: OSPF - Router As A Gateway And Has An Own Gateway?

Jan 29, 2013

Can a router using OSPF propagate that he is a router with default-information originate... at the same time when he got an own gateway of last resort to an IP-adress? If so, how? I can't get it to work.

View 8 Replies View Related

Gateway 2wire 3800 HGV-B Router - Wireless Working Properly But Wired Isn't?

Jul 22, 2012

I've got a Gateway 2wire 3800 HGV-B router which works fine wirelessly, but when using an ethernet cable to connect to the internet, it doesn't even recognize the computer. My laptop runs wirelessly all the time, and I recently picked up a desktop PC for home here, and it's the first wired connection I'm using, but for some reason the wired connection isn't connecting to my network, but instead it's own Unidentified Network.

View 2 Replies View Related

Cisco Routers :: RV082 Gateway To Gateway VPN Not Resolving Remote DynDns

Feb 14, 2013

I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
 
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.

View 2 Replies View Related

Cisco Routers :: How To Manage Port 80 Hosts Via Gateway To Gateway VPN (rv220w)

Aug 30, 2012

I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...

View 0 Replies View Related

Cisco Routers :: RV220W Gateway-to-Gateway Inter VLAN Routing?

Jul 6, 2012

I picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly.  What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there.  For what its worth: While I have some IT experience, I don't have strong networking experience.
 
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site.  Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
 
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up.  Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
 
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected.  But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me.  I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
  
'TECHNICAL' SPECS
 
 Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs

[URL]

View 7 Replies View Related

Cisco Security :: Rv042 Vpn Openswan Gateway To Gateway Linux Unbutu

Sep 13, 2012

config setup
protostack=netkey
klipsdebug=none

[Code]....

View 3 Replies View Related

Cisco Routers :: RVS4000 To Use A Gateway To Gateway IPSec Tunnel

Oct 17, 2011

Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?

View 1 Replies View Related

Cisco Routers :: RV042 Gateway To Gateway Tunnels Not Reconnecting

Apr 11, 2013

I have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either  router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.

View 2 Replies View Related

Cisco Routers :: RV016 Gateway To Gateway RV082 Won't Connect

Mar 9, 2012

New hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway  VPN
 
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address  some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
 
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address  some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
 
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.

View 2 Replies View Related

Cisco Routers :: Getting VPN Gateway To Gateway With NAT For Multiple Subnets / RV082?

Feb 11, 2012

I have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc).  I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity. 
 
Routing does behave as advertised, where all traffic does go to the main office.  However, the 192.168.1.0 subnet in the branch office does not get internet connectivity.  I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet.  Is  there a way to configure the RV082 router to provide NAT for all subnets?
 
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets?  Can the RV082 be used as part of the final solution or are my RV082s a  wasted expenditure?

Following is the configuration that I'd implemented, (real IP and IKE keys are bogus). 
  
Gateway To Gateway    
Remote                                                   Main Office
 Add a New Tunnel
Tunnel No.                  1                                               2
Tunnel Name :               n1-2122012_n2-1282012        n1-2122012_n2-1282012
Interface :                  WAN1                                    WAN1

[code].....

View 2 Replies View Related

Cisco Routers :: RV8082 Setup A VPN Tunnel With Gateway-to-Gateway

Apr 8, 2012

I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway.  One location is a static IP Address.  The other location is a dynamic IP address.

View 2 Replies View Related

Cisco VPN :: WRVS4400N VPN IPsec Gateway To Gateway Setup?

Jan 29, 2012

Just bought 3 WRVS4400N, I wanted to setup gateway to gateway VPN.  I followed the instructions on the WRVS4400N admin guide and VPN does not connect.  I also downloaded the VPN setup wizard and that also did get the gateway connected.  Everything seems to be correct.  Do I have to enable anything else?  Firewall setting?
 
Below is my config.
 
IPSec VPN Tunnel: Enabled
Tunnel Name: TUN01 
Local Security gateway: IP only
WAN1 IP: 192.168.100.1
SUBNET: 255.255.255.0
Local Security type: subnet
LOCAL IP: 10.10.10.1
SUBNET: 255.255.255.0

[code]....

View 1 Replies View Related

Cisco Routers :: Gateway To Gateway VPN Between RV110W And RV042G?

Mar 19, 2013

I am trying to set up a gateway to gateway VPN connection between a RV042G (central site) and a RV110W (newest firmware) which is used for presentation purposes on various customer's sites. The RV042G has a static IP. The RV110W has different IPs, depending on where it is used.
 
Basic VPN settings are clear to me (we have another VPN between two RV042G with static IPs). I set up the VPN connection on the RV042G wth the following settings for "Remote Group Setup":
 
Remote Security Gateway Type : IP + Domain Name (FQDN) Authentication IP by DNS resolved: mydomain.no-ip.org Domain Name: router12345
 
The value "router12345" is what I have configured in the RV110W as "Host name" in the network settings.
 
This configuration does not work so I am obviously doing something wrong. Do I have to use "router12345.mydomain.local" instead if I configured "mydomain.local" as the domain name in the RV110Ws network settings? For my tests the RV110W has a WAN-IP of 192.168.178.100 because it is located behind a DSL-Router. The external IP of this DSL-router is 178.0.x.x. The resolved IP  from mydomain.no-ip-org is 192.168.178.100 but when I look in the RV042G log I see the requests coming withg the external IP (178.0.x.x). Is this the problem? The last message I see in the log is "no connection has been authorized with policy=PSK".
 
Or can I use "IP + Email Address (USER FQDN) Authentication" instead (where can I enter this email address in the RV110W?). Or do I have to use "Dynamic IP"?

View 1 Replies View Related

Linksys Cable / DSL :: WCG200 Bridge Mode From Wireless-G Cable Gateway To Wired?

Mar 14, 2013

Our family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:

- WLAN AutoConfig service has successfully stopped.Wirel?

- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll

- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.

- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down.  Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]

Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.

View 9 Replies View Related

Cisco VPN :: RV042G / 1721 - Gateway To Gateway VPN

Mar 23, 2013

I try to install a Gateway to Gateway VPN between a RV042G router (LAN1) and a 1721 router (LAN2). The VPN is connected. I can ping the devices from a LAN to the other in the two way.
 
But otherwise I can't access to the devices of LAN2 from LAN1 like with telnet, HTTP, mstsc, ....

And it is OK to access to the devices of LAN1 from LAN2....
 
Normally I access to all the resources of LAN2 with the Cisco VPN Client but i try to change it with this router. The firewalls are off on all the computers I look.

View 2 Replies View Related

Cisco Routers :: RV042G - Gateway To Gateway VPN

Dec 19, 2012

I exchanged a RV042 v1.2 (Firmware 1.3.13.02) by a new RV042G v3. (Firmware 4.2.1.02).
 
My problem is now the following: The old RV042 established the Gateway to gateway VPN connection as soon as an IP- address of the remote location was requested. The new RV042G stays on „Waiting for connection“ all the time and does nothing at all. The connection works by clicking „CONNECT“ or by ticking Keep-Alive in the advanced tunnel settings but NOT automatically as before. Is this a firmware issue or have I to configure something additional?

View 1 Replies View Related

Gateway Netbook Cannot Connect To Network - Wired Or Wireless

Aug 1, 2012

The netbook was working fine on wireless network; didnt use it for a couple of days - now I cannot conenct wired or wireless; cannot see the wired or wireless modem , only MSN dial up. But the wireless modem light is blinking steadily. Otherwise the netbook is working OK - it even seems to boot up quicker than it used to)(I would reinstall the OS but it didnt come with OS DVD or a DVD drive ; so I didnt create a backup when I bought it. I have since purchased a USB DVD drive; this is one of two identical netbooks I purchased on black Friday - other one works perfectly?

View 2 Replies View Related

Set Up My Linksys N Router With Uverse Gateway?

Aug 25, 2011

So we just had Att Uverse installed in our apartment and the 2wire box has not been too reliable. I was trying to set up my Linksys router to provide an additional wireless network but i was having some problems with the set-up

View 3 Replies View Related

Linksys Gateway WAG54GS Router Does Not Work Wirelessly

Apr 21, 2011

I am having problems with my linksys wireless G ADSL gateway WAG54GS router. I am on Windows Vista/Internet Explorer. When I set up the router to work on the internet when I first bought it (several years ago), something must have gone wrong in the installation because it works only when connected to the computer by the lead, and NOT wirelessly.

While this is fine for general internet browsing etc on the main computer, my problem now is that I cannot connect anything else to it (such as my Playstation 3) because the router does not work wirelessly and I do not have the WPA key that the PS3 asks for. Is there any way can fix this without doing a complete reset on the router?

[ALSO: the router also periodically goes wrong, e.g. loses connection for no reason at all - I often have to disable and then enable the internet connection, or turn the router off for 15 seconds then switch it on again, and then it's fine again. I live in a rural area though, so it might be because of a poor connection. Our telephone connecton isn't very good either and sometimes goes wrong.]

View 4 Replies View Related

Install 2wire Gateway Behind Linksys Wireless Router?

Oct 30, 2011

I currently have Comcast as my ISP.However there are only 4 wired ports on the router and I need an additional 2 ports for my needs. I have a 2wire 38000HGV-B Uverse Wireless gateway. I wanted to know if I could use one of the output ports from the Comcast wireless gateway and feed the 2wire Gateway to achieve the additional ports that I need. Also the wireless router from comcast is so difficult to setup that I don't even use the wireless. The 2wire gateway is much easier to setup and use and I could have wireless available where I don't have it right now.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved