Linksys Wired Router :: Should Set RV042 Up As Gateway Or As Router
Aug 8, 2011
I am setting up an RV042 for my small business office and I am trying understand how it needs to be configured.
-For WAN1 I have a Wildblue Satellite Modem connected IP 220.127.116.11
-For WAN2 I have a Cradlepoint CTR35 Router with a verizon AirCard Connected IP 192.168.0.1
(Verizon has a 5GB download limit and wildblue has a 17GB download limit but it drops out in poor weather)The LAN is IP 172.16.0.1 Subnet Mask 255.255. 255. 0Should I set the RV042 up as a gateway or as a router?
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
I am using the default configuration at this point. I just connected 1 computer using the default IP with DHCP on the RV042 router. 192.168.1.0/255.255.255.0.I connect my wildblue satalite modem using a static IP address 75.106.203.xxx / 255.255.252.0 I can ping the RV042 router and the static IP address of the wildblue router but I can't ping the gateway on the wildblue side. Either from the PC or the Router diag tools.
Comcast installed a new fiber 10M EDI internet connection in our facility the other day and found out it is our responsibility to provide a layer 3 gateway to map the internet connection to the 14 public IP addresses they assigned to us. We are using RV042 for our existing networks with a T1 we had.
Will the RV042 provide the gateway function to route the single IP address comcast provided to the 15 public IP addresses? If so , can you provide the configuration example on this process?
Comcast EDI Connection ---> ???????? ----> 14 Static External Addresses
Interconnect Block 18.104.22.168 / 255.255.255.252.Comcast Gateway is 22.214.171.124Clear Layer 3 device WAN interface: 126.96.36.199Usable IP Block 188.8.131.52/28Mask: 255.255.255.240Usable Addresses: 184.108.40.206 - 220.127.116.11
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings: IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
I have configured 2 RV042 VPN with different ISP. Tunnel connected successfully and i can ping each other router but i can access clients which are connected to router. I have added rules also in firewall.
I've installed a RV042 and my terminals cant even ping each other. They have Internet, but they cannot ping each other, or open network shares. It is not a dns problem becouse it does not work with the IP.
I have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
I would like to the the RV042 for a one to one NAT, but I need it to NAT to an address that is not on it's local subnet. I have it routing properly to the address, but web interface only allows adding an IP on the local subnet. Is there a way around that?
We have 3 Cisco RV042. These were purchased to permit VPN from two branch offices to our head office. VPN is required to permit the two branch offices to use Avaya IP phones to connect to our main head office switchboard.We also have users on Blackberry and Apple iPhones to collect their mail through OWA from our Exchange 2010 server.
I've noticed in one of your threads that the RV042 routers configured for VPN do not permit the use of HTTPS to connect to OWA and that seems to be the problem for us. Since installing the VPN our OWA access is not possible.
What can I do to resolve this problem and what router would you suggest that I could use at the head office to enable the two branches to connect VPN to head office? And if there is a suitable router, would I need to replace all three?
I'm experiencing quite a slow vpn performance. I've tested different scenarios.* Windows XP with built-ín pptp client and Shrew ipsec client* Linux built-in pptp* wireless and wired connections? I never managed to go above 1MBps neither with windows or linux. I managed to go up to 3MBps using the Shrew client.I've also checked mtu settings and everything seems to be fine.
I am converting from a Cisco Model 850 to a RV042, all is well so far but I cannot implement one feature I had on the old router.I want to do one to one nat from one internal ip to one external ip but I only want to use one tcp/ip port.The command to do this on the old cisco 850 was this:"ip nat inside source static tcp 192.168.1.181 80 75.xxx.xxx.181 80 extendable"Can this be done with the RV042?I can do one to one nat but it include all ports.
my office network is running using a Linksys Router RV042 and at home i have a Linksys Router BEFVP41. i'm trying to setup a QuickVPN from home to my office but having problems. both routers have different LAN IPs. the firmware version for my two routers are listed belowRV042 - ver. 18.104.22.168BEFVP41 - ver. 1.02.00?
LAN L1, with IP addresses 192.168.10.x, for Company C1 LAN L2, with IP addresses 192.168.11.x, for Company C2
I have networks separated: different racks (but very closer fisically: a wire can be thrown), different gateways (to DSL), but both LAN's must connect with each other. I have acquired two RV042, one for each company to create VPN's (permitting telejob).
I tried to upgrade the firmware of my RV042 router. I downloaded the file (RV0XX-v4.0.0.07-tm-20100819-code.bin) and check the cheksum. When I try to upload it, I have the message "413 Request Entity Too Large". How can I do ? Should I unzip the .bin file (it's about 30Mo) ?
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up . [IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
My quickvpn setup has been working great for a few years but it stop working recently with the following error message in wget_request_error.txt: HTTP request sent, awaiting response... 501 Not Implemented 20:10:10 ERROR 501: Not Implemented.quickvpn hangs on the dreaded verifying network stage.Checked VPN router logs and also quickVPN client logs and confirmed the tunnel has been created successfully. However the ping was unsuccessful.I look through the forum and confirmed that my quickvpn user account and password only contains alphanumeric characters.
We have a Network set up with a RV042 router. Router is hooked up to Cox Cable and ATT DSL. Currently have 20 computers hooked up to the router all using Static IP addresses. Setup has been in place for over 7 years. I want to set up a Wireless Access point on this network. The problem is, I can't seem to get DHCP to work right even WITHOUT the Wireless Access Point. I have taken one of the computers that works great with a static IP and changed it to be DHCP, I have enabled DHCP on the router and set the from and thru parameters for the IP assignment. The computer will connect and get an IP address and it allows me to see all the INTERNAL servers on the network but going to the Internet is REAL FLAKY. I usually have to refresh 5 or 6 times to get a web page and sometimes even that don't work. If I do get a page to come up there is about a 10% chance that it will bring up a subpage of that page without doing a refresh 5 or 6 times. Its like it won't hold the connection to the Internet. I did notice one thing different in the User Manual of the RV042 that is different than all the other Linksys routers I have worked with. It says that when you enable the DHCP on the router, you then make sure ALL computers hooked to it are set for DHCP. All other routers I have worked with do NOT use that word ALL. Am I missing some setting or is this a binding thing where you are either ALL static or ALL DHCP?
Small office, 2 RV042, 2 DSL connections. 1 is used striclty for the business side, and the other is for our CCTV network. They also have seperate DSL connections as we have 2 external IP address for clients to connect remotely. We don't want to take away our exisring setup, but would like to bridge both networks so a few of our internal clients can connect to our CCTV network and use some of the devices. Right now they come in on VPN but its not as fast.Is this doable without adding additional hardware? Both networks need DHCP enable as well.
I have been running a email/web/ftp server on one server for 9 years. I have currently acquired a Barracuda spam 300. I cant get the emails to go thru the barracuda first. Here is how it is setup: my email and web come in thru one outside address..call it 22.214.171.124 I have a 1 to 1 nat for 126.96.36.199 to 10.0.0.2 (email/web/ftp server) ports 25 and 53 are forwarded to the 10.0.0.4 (barracuda) then out on 25 to my 10.0.0.2 no emails go thru as long as it is set this way I can nat the 188.8.131.52 to the barracuda first and emails go thru, but I lose my web and ftp will this router work for me? I was told that i needed to change mx records for email to 184.108.40.206 and then forward nat on that address to the barracuda. I dont really want to change mx records for 10-12 email domains.
I am currently using Netgear FVS338 Routers / VPN Devices in 3 different locations and honestly I am not happy / impressed with them whatsoever.I have been doing some research and came across the Linksys RV042 and RV082 devices that caught my eye. The question is what is the VPN throughput of these devices?I have gone over the website, spec sheets and they only really say the throughput of the LAN Links and not the WAN Links. I currently have very reliable 20Mb+ Synchronous connections between all 3 sites and have not been able to get any good performance out of the Netgear devices and contacting their support is a joke. They can't tell you anything other than it should work or we will swap out the unit. Well if I have 3 of them that have been purchased at all different times I don't believe that they are all having the same issues. What these units 3DES VPN Throughput and will more than likely be purchasing 3 of which ever once suits our needs immediately.
I have a RV042 router and we are trying to set-up our OWA for outside access. I can't figure out which ports or which page those ports are on to open them. We are a small company and we do not have IT except for ourselves. The internal network works fine but i can't get the Exchange access from outside.
Having a problem everytime I try to use load balance on my Rv042 it is slow as a dog and sometimes wont connect at all. if I run in smart backup mode its fine. removed firewall rebooted everything tried numerous configerations upgraded to the latest frimware just about to be convinced
I've got an RV042 router at home and am connected from my office via the QuickVPN client ver 220.127.116.11.2. I can ping the RV042 and log into the administration page and make changes. However, I can not see other computers on the remote network. I can not ping them. When I open my Network page, I still see the computers on my local network.
All machines are running Windows 7 Ultimate. ISP is Comcast at both locations. WAN IP's are dynamic, but have not changed in over a year. Local IP's on the remote (home) network are static..[url]....