Linksys Wired Router :: RV042 - Can't Access Internet Or Ping Gateway
Jan 4, 2011
I am using the default configuration at this point. I just connected 1 computer using the default IP with DHCP on the RV042 router. 192.168.1.0/255.255.255.0.I connect my wildblue satalite modem using a static IP address 75.106.203.xxx / 255.255.252.0 I can ping the RV042 router and the static IP address of the wildblue router but I can't ping the gateway on the wildblue side. Either from the PC or the Router diag tools.
View 1 Replies
ADVERTISEMENT
Jul 11, 2012
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies
View Related
Feb 8, 2011
we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies
View Related
Mar 22, 2011
I have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
View 1 Replies
View Related
Apr 6, 2013
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies
View Related
Jul 26, 2012
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
View 1 Replies
View Related
Feb 7, 2013
Comcast installed a new fiber 10M EDI internet connection in our facility the other day and found out it is our responsibility to provide a layer 3 gateway to map the internet connection to the 14 public IP addresses they assigned to us. We are using RV042 for our existing networks with a T1 we had.
Will the RV042 provide the gateway function to route the single IP address comcast provided to the 15 public IP addresses? If so , can you provide the configuration example on this process?
Comcast EDI Connection ---> ???????? ----> 14 Static External Addresses
Interconnect Block 51.235.227.60 / 255.255.255.252.Comcast Gateway is 51.235.227.61Clear Layer 3 device WAN interface: 51.235.227.62Usable IP Block 51.235.227.96/28Mask: 255.255.255.240Usable Addresses: 51.235.227.97 - 51.235.227.110
View 1 Replies
View Related
Aug 8, 2011
I am setting up an RV042 for my small business office and I am trying understand how it needs to be configured.
-For WAN1 I have a Wildblue Satellite Modem connected IP 70.66.93.4
-For WAN2 I have a Cradlepoint CTR35 Router with a verizon AirCard Connected IP 192.168.0.1
(Verizon has a 5GB download limit and wildblue has a 17GB download limit but it drops out in poor weather)The LAN is IP 172.16.0.1 Subnet Mask 255.255. 255. 0Should I set the RV042 up as a gateway or as a router?
View 1 Replies
View Related
Jan 27, 2012
I am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
View 2 Replies
View Related
Nov 24, 2009
I have a RV042 router and we are trying to set-up our OWA for outside access. I can't figure out which ports or which page those ports are on to open them. We are a small company and we do not have IT except for ourselves. The internal network works fine but i can't get the Exchange access from outside.
View 2 Replies
View Related
Apr 4, 2011
We have an RV042 router.I'm looking for a solution where my drop-in clients would have their own WIFI key to access Internet, with no access to our LAN.
-Can I place a Wifi AccessPoint on the DMZ so my drop-in clients use it to connect to the WEB.
-While putting another Wifi AccessPoint on a regular LAN port for Employees to use and stay within the LAN?
View 2 Replies
View Related
Jun 2, 2011
I have a RV042:Firmware Version : v4.0.0.07-tm (Aug 19 2010 19:19:50)PID VID : RV042 V03 .Configured with a internal LAN address (10.0.17.0/24) and ISP PPPoE External address on WAN1.I´ve configured a VPN with a remote location (Fortigate 4) and after the VPN starts up the RV042 cannot ping any machine in their local network (using the diagnostic, all pings failed in 10.0.17.0/24) and no machines in that network can PING and access or manage the RV042
The only way to manage the RV042 after VPN starts UP is using a machine in the other side of the VPN (The Main office)If i force the VPN down, the connectivity begins to work, but as soon the VPN starts up again, the local/LAN connectivity loses again.
View 1 Replies
View Related
Jul 20, 2011
We have an RV042 as main router.We have a netgear WNR2000v2 as WIFI router.We would like to offer our drop-in customers an internet access. But without letting them into our network.
View 1 Replies
View Related
Dec 7, 2011
i have 2 rv042 with a vpn tunnel between them.the problem is that i can't access https over the VPN !if i telnet 192.168.10.1 443 through the VPN, it's not working either. if i telnet 192.168.10.1 443 in my 192.168.10.0 network it's working so it's reall the VPN tunnel the problem.
View 1 Replies
View Related
Jun 23, 2012
I have configured 2 RV042 VPN with different ISP. Tunnel connected successfully and i can ping each other router but i can't access clients which are connected to router. I have added rules also in firewall.
View 1 Replies
View Related
May 20, 2007
Having a problem everytime I try to use load balance on my Rv042 it is slow as a dog and sometimes wont connect at all. if I run in smart backup mode its fine. removed firewall rebooted everything tried numerous configerations upgraded to the latest frimware just about to be convinced
View 2 Replies
View Related
Jun 7, 2012
how i can configure the Cisco RV042 to access PPTP VPN Server (Witopia VPn) or other vpn servers.
View 1 Replies
View Related
Jun 23, 2012
I have configured 2 RV042 VPN with different ISP. Tunnel connected successfully and i can ping each other router but i can access clients which are connected to router. I have added rules also in firewall.
View 1 Replies
View Related
Feb 24, 2013
In our USA office we have a RV042 router and in Venezuela we have a RV082 router. We have connected a VPN tunnel (gateway-to-gateway) between both offices.
The point is: How could we redirect the internet traffic from our Venezuela office (RV082) to the USA Office (RV042) to navigate using USA public IP's?
The reason for this is that we need to use online streaming services which are only available for IP's from USA and we can't use them from the Venezuelan IP's.
We can not use the PPTP option since the equipment which will use the streaming services (like hulu, crackle, etc.) in Venezuela is a Google TV device which doesn't allow the configuration of proxy navegation or PPTP VPN connections itself. That's the reason why we need to do that through the routers.
View 1 Replies
View Related
Mar 20, 2012
Currently i am having a scenario where i have setup RV042 and which is connected to Microsoft Forefront 2010. PPTP works fine only on rv042 subnet but i am not able to access the "internal" network of TMG.RV042 (172.16.1.1) ---> TMG [external] (172.16.1.2) ---> TMG [internal] (192.168.1.1) Is there any way through static route to access the TMG internal network through RV042 pptp server?
View 1 Replies
View Related
Oct 10, 2008
I am having problems with my RV042.I have a Intervoip(url...) account for VOIP.
When I try to register the intervoip account to the internet I don't get any kind of reply. My VOIP server just keeps requesting to register the SIP account, but gets no reply.
When I connect an other router to my ISP modem, the register just goes fine. However the RV042 blocks something I don't really know what the cause could be.I installed wireshark to monitor my network traffic.
When I monitor registering with intervoip with the RV042, I see requests but no replies from intervoip, the VOIP server keeps requesting, but doesn't get any reply.
When I monitor registering with intervoip with an other router, I see requests from the VOIP server, and replies from intervoip initiating my intervoip account and everything goes well and registers. The following I tried:
- Forwarding port 5060 to private ip
- Putting private ip in DMZ
- Disabled the firewall
All without result. (Also tried them all at once)
View 8 Replies
View Related
Feb 28, 2012
I was able to install the RV042 router to my ATT DSL line (WAN1 port-INTERNET) and it gets an external IP address automatically and the Internet works. When I connect my Comcast Internet to WAN2 port INTERNTE/DMZ) it doesn't get an IP address. and the Internet goes down and the WAN2 port ip address says 0.0.0.0.I've tried releasing/ renewing and it still says 0.0.0.0.Everything else is set as the default.
View 1 Replies
View Related
Jan 24, 2012
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
View 1 Replies
View Related
Apr 12, 2011
We recently upgraded from a Linksys WRT54G router to a Cisco RV042 to gain "gateway-to-gateway" automated VPN access. However, we are unable to get "client to gateway" access working.
With the Linksys WRT54G we used a "username" "password" pair for remote client authenication. This worked for both Windows and Mac OS X users using the built-in PPTP client. We found we had to set "encryption" value to "none" on the client side.
I am confused by the setup screens on the RV042. It looks like I must setup a "tunnel" (VPN->Client to Gateway), there is (VPN->VPN Client Access) where I can enter a username/password, and also (VPN->PPTP Server) where another username/password pair can be entered. I have tried all sorts of combinations but "no love". I am particularly mystified by the (VPN->Client to Gateway) settings for "Remote Client Setup"; the client can be calling in from anywhere and there is an option for "Dynamic IP + Email Address" but I'm not sure how that maps onto the client (do they use the email address as their account name?). I have also looked at defining a "Group VPN" where I am given other options. But nothing works from the client.
I just need to come up with some setup that works, that I can document to both PC and Mac users at a miniumum.
View 1 Replies
View Related
Mar 6, 2011
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
View 1 Replies
View Related
Sep 23, 2012
I purchased and set-up the EA4500 on Thursday. Friday my ISP (Charter) was out and worked on connection for over 2 hours due to slowness issues. Connected directly to modem I get normal ping times on whichever computer is connected. When I get the computer connected by the router (hard wired) I get very long ping responses up to 900ms. They are all over the place 30ms (I can live with that), up to the 900's. I contacted Linksys support last night, who had me update to the cloud firmware and change MT U to 1300, have not noticed a difference. I did end up doing a hard reset on the router last night after I lost tech support. We were disconnected with router rebooted, and I didn't have the patience to connect again last night.
It was so slow on my work computer, a pint to yahoo timed out. The computers connecting to router are
XP SP3 (mine)
Win 7 Home (IPV6 turned off)
Work laptop that uses VPN and VOIP
View 5 Replies
View Related
Mar 30, 2013
Belkin N750 Router - wired connection can not access Internet. I've tried direct to modem and have no problem, have tried old router, no problem, but if I shut down desktop completely (Win7) and restart, I get no connection. Uninstalling the NIC (Intel 82579V Giga) and restarting, then I get connection again. However, if I start in safe mode with networking, I have no problems at all. I've disabled my firewall to no avail.
View 3 Replies
View Related
Nov 11, 2011
I have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies
View Related
Feb 21, 2011
A while ago internet access was slowed right down for an hour or so. I have a phone line that comes into the house and then into gateway (10.0.0.2) then ethernet from that to linksys wifi router (192.168.1.1). So I did the following ping and repeated what you see below a few times to see that these results were broadly consistent, which was the case. One other person is connected to linksys via ethernet cord and they might have been on at the time. Questions are.... are these results consistent with contention caused by other user on the linksys? and why can I ping gateway but not the router? That makes no sense to me! I am not annoyed with the other person if he is hogging the network...I like him. I just wonder whats going on. When the internet works results from pinging are all as one would expect
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsNASA>ping 192.168.1.1
[Code].....
View 4 Replies
View Related
Jan 17, 2011
I would like to the the RV042 for a one to one NAT, but I need it to NAT to an address that is not on it's local subnet. I have it routing properly to the address, but web interface only allows adding an IP on the local subnet. Is there a way around that?
View 1 Replies
View Related
Mar 24, 2012
We have 3 Cisco RV042. These were purchased to permit VPN from two branch offices to our head office. VPN is required to permit the two branch offices to use Avaya IP phones to connect to our main head office switchboard.We also have users on Blackberry and Apple iPhones to collect their mail through OWA from our Exchange 2010 server.
I've noticed in one of your threads that the RV042 routers configured for VPN do not permit the use of HTTPS to connect to OWA and that seems to be the problem for us. Since installing the VPN our OWA access is not possible.
What can I do to resolve this problem and what router would you suggest that I could use at the head office to enable the two branches to connect VPN to head office? And if there is a suitable router, would I need to replace all three?
View 1 Replies
View Related
Aug 18, 2011
I have never setup a GW to GW VPN with a FIOS connection. I have done it with DSL and cable without any problems.
View 1 Replies
View Related
Feb 10, 2011
I'm experiencing quite a slow vpn performance. I've tested different scenarios.* Windows XP with built-ín pptp client and Shrew ipsec client* Linux built-in pptp* wireless and wired connections? I never managed to go above 1MBps neither with windows or linux. I managed to go up to 3MBps using the Shrew client.I've also checked mtu settings and everything seems to be fine.
View 1 Replies
View Related
