Linksys Wired Router :: RV042 VPN Can't Access Connected Clients

Jun 23, 2012

I have configured 2 RV042 VPN with different ISP. Tunnel connected successfully and i can ping each other router but i can't access clients which are connected to router. I have added rules also in firewall.

View 1 Replies


ADVERTISEMENT

Linksys Wired Router :: RV042 Can Access Clients Which Are Connected To Router

Jun 23, 2012

I have configured 2 RV042 VPN with different ISP. Tunnel connected successfully and i can ping each other router but i can access clients which are connected to router. I have added rules also in firewall.

View 1 Replies View Related

Linksys Wired Router :: RV042 - Can't See Remote Computers When Connected Via VPN

Feb 10, 2011

I've got an RV042 router at home and am connected from my office via the QuickVPN client ver 1.4.1.1.2.  I can ping the RV042 and log into the administration page and make changes.  However, I can not see other computers on the remote network.  I can not ping them.  When I open my Network page, I still see the computers on my local network.
 
All machines are running Windows 7 Ultimate.  ISP is Comcast at both locations.  WAN IP's are dynamic, but have not changed in over a year.  Local IP's on the remote (home) network are static..[url]....

View 1 Replies View Related

Linksys Wired Router :: RV042 - Setup OWA For Outside Access?

Nov 24, 2009

I have a RV042 router and we are trying to set-up our OWA for outside access. I can't figure out which ports or which page those ports are on to open them. We are a small company and we do not have IT except for ourselves. The internal network works fine but i can't get the Exchange access from outside.

View 2 Replies View Related

Linksys Wired Router :: Rv042 / Wifi Access Point On Dmz

Apr 4, 2011

We have an RV042 router.I'm looking for a solution where my drop-in clients would have their own WIFI key to access Internet, with no access to our LAN.
 
-Can I place a Wifi AccessPoint on the DMZ so my drop-in clients use it to connect to the WEB.

-While putting another Wifi AccessPoint on a regular LAN port for Employees to use and stay within the LAN?

View 2 Replies View Related

Linksys Wired Router :: After VPN Starts / Lose Access To RV042

Jun 2, 2011

I have a RV042:Firmware Version : v4.0.0.07-tm (Aug 19 2010 19:19:50)PID VID : RV042 V03 .Configured with a internal LAN address (10.0.17.0/24) and ISP PPPoE External address on WAN1.I´ve configured a VPN with a remote location (Fortigate 4) and after the VPN starts up the RV042 cannot ping any machine in their local network (using the diagnostic, all pings failed in 10.0.17.0/24) and no machines in that network can PING and access or manage the RV042
 
The only way to manage the RV042 after VPN starts UP is using a machine in the other side of the VPN (The Main office)If i force the VPN down, the connectivity begins to work, but as soon the VPN starts up again, the local/LAN connectivity loses again.

View 1 Replies View Related

Linksys Wired Router :: Guest Network Access / RV042

Jul 20, 2011

We have an RV042 as main router.We have a netgear WNR2000v2 as WIFI router.We would like to offer our drop-in customers an internet access. But without letting them into our network.

View 1 Replies View Related

Linksys Wired Router :: Rv042 Vpn Tunnel - Can't Access HTTPS

Dec 7, 2011

i have 2 rv042 with a vpn tunnel between them.the problem is that i can't access https over the VPN !if i telnet 192.168.10.1 443 through the VPN, it's not working either. if i telnet 192.168.10.1 443 in my 192.168.10.0 network it's working so it's reall the VPN tunnel the problem.

View 1 Replies View Related

Linksys Wired Router :: RV042 - Can't Access Internet Or Ping Gateway

Jan 4, 2011

I am using the default configuration at this point.  I just connected 1 computer using the default IP with DHCP on the RV042 router. 192.168.1.0/255.255.255.0.I connect my wildblue satalite modem using a static IP address 75.106.203.xxx / 255.255.252.0 I can ping the RV042 router and the static IP address of the wildblue router but I can't ping the gateway on the wildblue side.  Either from the PC or the Router diag tools.

View 1 Replies View Related

Linksys Wired Router :: Configure Cisco RV042 To Access PPTP VPN Server?

Jun 7, 2012

how i can configure the Cisco RV042 to access PPTP VPN Server (Witopia VPn) or other vpn servers.

View 1 Replies View Related

Linksys Wired Router :: Static Route To Access TMG Internal Network Through RV042 Pptp Server?

Mar 20, 2012

Currently i am having a scenario where i have setup RV042 and which is connected to Microsoft Forefront 2010. PPTP works fine only on rv042 subnet but i am not able to access the "internal" network of TMG.RV042 (172.16.1.1) ---> TMG [external] (172.16.1.2) ---> TMG [internal] (192.168.1.1) Is there any way through static route to access the TMG internal network through RV042 pptp server?

View 1 Replies View Related

Linksys Wired Router :: RV016 - Allow Other Networks Connected To Firewall To Access Internet?

Nov 24, 2011

I have a sonicwall firewall connected to the LAN port of the RV016 router and two DSL modems connected to the WAN ports.
 
Ip address allocation:

Firewall
192.168.50.9
RV016
LAN  - 192.168.50.10
WAN - 192.168.60.1
WAN - 192.168.61.1
 
What configurations do I need to enter into the RV016 to allow other networks connected to the firewall(192.168.3.0, 192.168.2.0) to access the internet?

View 1 Replies View Related

Linksys Wired Router :: Setting Up RVS4000 For VPN Clients?

Apr 21, 2011

I've looked through the documentation that came with the router and there is no instructions on how to configure the 4000 to accept remote clients and access the local network.  What the configurations are so a client can launch the vpn client, login, and remote desktop to their local workstations in the office?  I don't have any tunnels or connections setup with other offices, just a simple client connection.Also, will the rvs4000 work with Cisco VPN client (comes with higher end appliances)?

View 1 Replies View Related

Linksys Wired Router :: RV042 One-to-One NAT Subnet?

Jan 17, 2011

I would like to the the RV042 for a one to one NAT, but I need it to NAT to an address that is not on it's local subnet. I have it routing properly to the address, but web interface only allows adding an IP on the local subnet. Is there a way around that?

View 1 Replies View Related

Linksys Wired Router :: OWA Through RV042 With VPN Running

Mar 24, 2012

We have 3 Cisco RV042. These were purchased to permit VPN from two branch offices to our head office. VPN is required to permit the two branch offices to use Avaya IP phones to connect to our main head office switchboard.We also have users on Blackberry and Apple iPhones to collect their mail through OWA from our Exchange 2010 server.
 
I've noticed in one of your threads that the RV042 routers configured for VPN do not permit the use of HTTPS to connect to OWA and that seems to be the problem for us. Since installing the VPN our OWA access is not possible.
 
What can I do to resolve this problem and what router would you suggest that I could use at the head office to enable the two branches to connect VPN to head office? And if there is a suitable router, would I need to replace all three?

View 1 Replies View Related

Linksys Wireless Router :: EA4500 - Unable To See Wired Clients

Jun 9, 2012

Very strange problem with an EA4500 running 2.0.37.131047.  Set it up in no time with a Mixed network on WPA2 Personal, Internet's fine, but I can't see any of my wired clients.  They don't ping at all.  Even stranger, if I plug into another wired switch port with my laptop, I STILL can't ping the other clients.  One is a NAS and one is a network printer so there are no firewalls involved.  I power cycled the printer but in vain.  I've already reset to factory defaults once, but that didn't work.  I'm thinking I'll need to return it.

View 4 Replies View Related

Linksys Wired Router :: RV042 GW To GW VPN Using Verizon FIOS

Aug 18, 2011

I have never setup a GW to GW VPN with a FIOS connection.  I have done it with DSL and cable without any problems. 

View 1 Replies View Related

Linksys Wired Router :: RV042 Slow Vpn Performance?

Feb 10, 2011

I'm experiencing quite a slow vpn performance. I've tested different scenarios.* Windows XP with built-ín pptp client and Shrew ipsec client* Linux built-in pptp* wireless and wired connections? I never managed to go above 1MBps neither with windows or linux. I managed to go up to 3MBps using the Shrew client.I've also checked mtu settings and everything seems to be fine.

View 1 Replies View Related

Linksys Wired Router :: RV042 / One-To-One NAT From Internal To External IP?

Mar 10, 2012

I am converting from a Cisco Model 850 to a RV042, all is well so far but I cannot implement one feature I had on the old router.I want to do one to one nat from one internal ip to one external ip but I only want to use one tcp/ip port.The command to do this on the old cisco 850 was this:"ip nat inside source static tcp 192.168.1.181 80 75.xxx.xxx.181 80 extendable"Can this be done with the RV042?I can do one to one nat but it include all ports.

View 1 Replies View Related

Linksys Wired Router :: QuickVPN From BEFVP41 To RV042?

Sep 24, 2006

my office network is running using a Linksys Router RV042 and at home i have a Linksys Router BEFVP41. i'm trying to setup a QuickVPN from home to my office but having problems. both routers have different LAN IPs. the firmware version for my two routers are listed belowRV042 - ver. 1.3.7.4BEFVP41 - ver. 1.02.00?

View 5 Replies View Related

Linksys Wired Router :: Connect Both LANs With Two RV042?

May 10, 2011

LAN L1, with IP addresses 192.168.10.x, for Company C1
LAN L2, with IP addresses 192.168.11.x, for Company C2
 
I have networks separated: different racks (but very closer fisically: a wire can be thrown), different gateways (to DSL), but both LAN's must connect with each other. I have acquired two RV042, one for each company to create VPN's (permitting telejob).

View 1 Replies View Related

Linksys Wired Router :: RV042 Firmware Upgrade

Feb 22, 2011

I tried to upgrade the firmware of my RV042 router. I downloaded the file (RV0XX-v4.0.0.07-tm-20100819-code.bin) and check the cheksum. When I try to upload it, I have the message "413 Request Entity Too Large". How can I do ? Should I unzip the .bin file (it's about 30Mo) ?

View 1 Replies View Related

Linksys Wired Router :: RV042 To Cisco ASA VPN Not Coming Up

Apr 25, 2013

i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
 
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.

[code]....

View 2 Replies View Related

Linksys Wired Router :: RV042 Error 501 Not Implemented

May 19, 2012

My quickvpn setup has been working great for a few years but it stop working recently with the following error message in wget_request_error.txt: HTTP request sent, awaiting response... 501 Not Implemented 20:10:10 ERROR 501: Not Implemented.quickvpn hangs on the dreaded verifying network stage.Checked VPN router logs and also quickVPN client logs and confirmed the tunnel has been created successfully. However the ping was unsuccessful.I look through the forum and confirmed that my quickvpn user account and password only contains alphanumeric characters. 

View 1 Replies View Related

Linksys Wired Router :: Static Route On RV042?

Apr 10, 2011

static route on RV042? 

View 1 Replies View Related

Linksys Wired Router :: DHCP Setup On RV042?

Mar 16, 2011

We have a Network set up with a RV042 router. Router is hooked up to Cox Cable and ATT DSL. Currently have 20 computers hooked up to the router all using Static IP addresses. Setup has been in place for over 7 years. I want to set up a Wireless Access point on this network. The problem is, I can't seem to get DHCP to work right even WITHOUT the Wireless Access Point. I have taken one of the computers that works great with a static IP and changed it to be DHCP, I have enabled DHCP on the router and set the from and thru parameters for the IP assignment. The computer will connect and get an IP address and it allows me to see all the INTERNAL servers on the network but going to the Internet is REAL FLAKY. I usually have to refresh 5 or 6 times to get a web page and sometimes even that don't work. If I do get a page to come up there is about a 10% chance that it will bring up a subpage of that page without doing a refresh 5 or 6 times. Its like it won't hold the connection to the Internet. I did notice one thing different in the User Manual of the RV042 that is different than all the other Linksys routers I have worked with. It says that when you enable the DHCP on the router, you then make sure ALL computers hooked to it are set for DHCP. All other routers I have worked with do NOT use that word ALL. Am I missing some setting or is this a binding thing where you are either ALL static or ALL DHCP?

View 1 Replies View Related

Linksys Wired Router :: Connecting 2 RV042 With Different Subnets And DSL

Apr 30, 2013

Small office, 2 RV042, 2 DSL connections. 1 is used striclty for the business side, and the other is for our CCTV network. They also have seperate DSL connections as we have 2 external IP address for clients to connect remotely. We don't want to take away our exisring setup, but would like to bridge both networks so a few of our internal clients can connect to our CCTV network and use some of the devices. Right now they come in on VPN but its not as fast.Is this doable without adding additional hardware? Both networks need DHCP enable as well.

View 1 Replies View Related

Linksys Wired Router :: Setting Up A Rv042 A Barracuda?

Aug 22, 2012

I have been running a email/web/ftp server on one server for 9 years. I have currently acquired a Barracuda spam 300. I cant get the emails to go thru the barracuda first. Here is how it is setup: my email and web come in thru one outside address..call it 166.5.5.5 I have a 1 to 1 nat for 166.5.5.5 to 10.0.0.2 (email/web/ftp server) ports 25 and 53 are forwarded to the 10.0.0.4 (barracuda) then out on 25 to my 10.0.0.2 no emails go thru as long as it is set this way I can nat the 166.5.5.5 to the barracuda first and emails go thru, but I lose my web and ftp will this router work for me? I was told that i needed to change mx records for email to 166.5.5.6 and then forward nat on that address to the barracuda. I dont really want to change mx records for 10-12 email domains.

View 1 Replies View Related

Linksys Wired Router :: Getting RV042 And RV082 Throughput?

Feb 17, 2008

I am currently using Netgear FVS338 Routers / VPN Devices in 3 different locations and honestly I am not happy / impressed with them whatsoever.I have been doing some research and came across the Linksys RV042 and RV082 devices that caught my eye. The question is what is the VPN throughput of these devices?I have gone over the website, spec sheets and they only really say the throughput of the LAN Links and not the WAN Links. I currently have very reliable 20Mb+ Synchronous connections between all 3 sites and have not been able to get any good performance out of the Netgear devices and contacting their support is a joke. They can't tell you anything other than it should work or we will swap out the unit. Well if I have 3 of them that have been purchased at all different times I don't believe that they are all having the same issues. What these units 3DES VPN Throughput and will more than likely be purchasing 3 of which ever once suits our needs immediately.

View 9 Replies View Related

Linksys Wired Router :: RV042 / Upgrading 1.3.12.19-tm To 4.0.0.07-tm Version?

Mar 28, 2011

Did anybody ever succeeded upgrading 1.3.12.19-tm to 4.0.0.07-tm version?

View 1 Replies View Related

Linksys Wired Router :: E2000 / E3000 - How Many Guest Clients Allowed In A Day

Jan 26, 2011

I would like to put an E2000 in an office where clients are coming and going throughout the day.  When the documentation says that there is a maximum of 10 guest network users allowed (with a default setting of 5) what exactly does that mean ?   I don't want the first 10 guest-clients who come in, connect to the guest network, then leave the office to consume all 10 slots for the day.If I have 50 people that come and go from the office throughout the day who connect to the guest 192.168.33.X network and attempt to enter the password (but no more than 10 guests authenticated at any given time) will all 50 be successful in connecting ?  Or do I have to reduce the Client Lease Time to something less than the default setting of one day ?

View 1 Replies View Related

Linksys Wired Router :: Really Slow Internet Rv042 In Dual Wan?

May 20, 2007

Having a problem everytime I try to use load balance on my Rv042 it is slow as a dog  and sometimes wont connect at all. if I run in smart backup mode its fine. removed firewall rebooted everything  tried numerous configerations upgraded to the latest frimware just about to be convinced

View 2 Replies View Related

Linksys Wired Router :: Configuring SMC 8014 And Cisco RV042

Apr 3, 2013

Spent a lot of time trying to configure a time warner set up. Users are using 2 SMC 8014 and one RVO42 on the network. Cannot access the internet.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved