Cisco Routers :: RV016 Gateway To Gateway RV082 Won't Connect
Mar 9, 2012
New hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
View 2 Replies
ADVERTISEMENT
Feb 14, 2013
I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
View 2 Replies
View Related
Feb 11, 2012
I have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc). I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity.
Routing does behave as advertised, where all traffic does go to the main office. However, the 192.168.1.0 subnet in the branch office does not get internet connectivity. I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet. Is there a way to configure the RV082 router to provide NAT for all subnets?
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets? Can the RV082 be used as part of the final solution or are my RV082s a wasted expenditure?
Following is the configuration that I'd implemented, (real IP and IKE keys are bogus).
Gateway To Gateway
Remote Main Office
Add a New Tunnel
Tunnel No. 1 2
Tunnel Name : n1-2122012_n2-1282012 n1-2122012_n2-1282012
Interface : WAN1 WAN1
[code].....
View 2 Replies
View Related
Jan 24, 2012
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
View 1 Replies
View Related
Jul 26, 2012
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
View 1 Replies
View Related
Aug 9, 2011
My rv082 router protect link gateway is already activated. How do i change the key or activate it with a new activation key?The router dont have any link to change the key. I'm using v1-2 rv082
View 4 Replies
View Related
Aug 30, 2012
I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...
View 0 Replies
View Related
Jul 6, 2012
I picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
'TECHNICAL' SPECS
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
[URL]
View 7 Replies
View Related
Oct 17, 2011
Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?
View 1 Replies
View Related
Apr 11, 2013
I have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.
View 2 Replies
View Related
Apr 8, 2012
I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway. One location is a static IP Address. The other location is a dynamic IP address.
View 2 Replies
View Related
Mar 19, 2013
I am trying to set up a gateway to gateway VPN connection between a RV042G (central site) and a RV110W (newest firmware) which is used for presentation purposes on various customer's sites. The RV042G has a static IP. The RV110W has different IPs, depending on where it is used.
Basic VPN settings are clear to me (we have another VPN between two RV042G with static IPs). I set up the VPN connection on the RV042G wth the following settings for "Remote Group Setup":
Remote Security Gateway Type : IP + Domain Name (FQDN) Authentication IP by DNS resolved: mydomain.no-ip.org Domain Name: router12345
The value "router12345" is what I have configured in the RV110W as "Host name" in the network settings.
This configuration does not work so I am obviously doing something wrong. Do I have to use "router12345.mydomain.local" instead if I configured "mydomain.local" as the domain name in the RV110Ws network settings? For my tests the RV110W has a WAN-IP of 192.168.178.100 because it is located behind a DSL-Router. The external IP of this DSL-router is 178.0.x.x. The resolved IP from mydomain.no-ip-org is 192.168.178.100 but when I look in the RV042G log I see the requests coming withg the external IP (178.0.x.x). Is this the problem? The last message I see in the log is "no connection has been authorized with policy=PSK".
Or can I use "IP + Email Address (USER FQDN) Authentication" instead (where can I enter this email address in the RV110W?). Or do I have to use "Dynamic IP"?
View 1 Replies
View Related
Dec 19, 2012
I exchanged a RV042 v1.2 (Firmware 1.3.13.02) by a new RV042G v3. (Firmware 4.2.1.02).
My problem is now the following: The old RV042 established the Gateway to gateway VPN connection as soon as an IP- address of the remote location was requested. The new RV042G stays on „Waiting for connection“ all the time and does nothing at all. The connection works by clicking „CONNECT“ or by ticking Keep-Alive in the advanced tunnel settings but NOT automatically as before. Is this a firmware issue or have I to configure something additional?
View 1 Replies
View Related
Jun 22, 2011
I am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)
View 1 Replies
View Related
Oct 12, 2011
Loss connection every day for several hours and just comes back. Reset router than works fine. Only about six months old. Found several forums staing the same problem. I have a RV016 16 port VPN router. What can I do?
View 1 Replies
View Related
Jun 1, 2011
VPN tunnel backup is not available on the RV016 firmware version 4.0.2.08 (it IS on the RV082. The data sheet and the manual for the RV016 is wrong. I have purchased several RV016 hardware V3 and several RV082 hardware V3. Both have the same current firmware version. We have noted that the RV016 does not have the VPN tunnel failover option found in the RV082. It also does not have split DNS (noted in the manual. A I would have thought that the firmware would provide equal options on the RV042, RV082, and RV016.
View 2 Replies
View Related
Apr 29, 2013
I know this *should* be simple but having a devil of a time getting it to work.
I have 2 routers. Both have a static ip. Each is setup for a different private subnet. At the moment they are not connected to each other. Consider this setup (made up numbers obviously):
RV016
has 13 lan ports, 2 internet ports, 1 dmz port
Internet port: 10.10.10.10
[Code].....
I'd like clients on the rv082 lan to be able to access the printer on the rv016 lan, and use the rv016 as an alternate internet connection (optional). I would prefer the rv016 client not be able to access the rv082.
View 3 Replies
View Related
Mar 25, 2011
I have RV082 in many locations and it is working fine.One location I just starting to have problem with packet lose (50 to 60 %)I ping between two location which i am having problem.Gateway to Gateway shows no lose on packet (reply with 20ms avg.)but router to router will lose packet 50 to 60 %.
View 1 Replies
View Related
Jun 1, 2013
I'm trying to setup an rv180w to connect as a client to an remote vpn gateway and route all the lan traffic behind it direct to the remote vpn gateway. [code]
View 3 Replies
View Related
May 16, 2012
I'd like to setup a WCCP in those routers, but as I read, it's not possible.
Another way to circumvent this limitation is to foward a request to the router from the LAN port 80 to a LAN IP, something like:
LAN 1 192.168.1.100:80 -> router -> LAN 2 192.168.1.101:80
View 1 Replies
View Related
Sep 13, 2012
config setup
protostack=netkey
klipsdebug=none
[Code]....
View 3 Replies
View Related
Jul 11, 2012
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies
View Related
Feb 8, 2011
we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies
View Related
Mar 22, 2011
I have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
View 1 Replies
View Related
Apr 6, 2013
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies
View Related
Jan 29, 2012
Just bought 3 WRVS4400N, I wanted to setup gateway to gateway VPN. I followed the instructions on the WRVS4400N admin guide and VPN does not connect. I also downloaded the VPN setup wizard and that also did get the gateway connected. Everything seems to be correct. Do I have to enable anything else? Firewall setting?
Below is my config.
IPSec VPN Tunnel: Enabled
Tunnel Name: TUN01
Local Security gateway: IP only
WAN1 IP: 192.168.100.1
SUBNET: 255.255.255.0
Local Security type: subnet
LOCAL IP: 10.10.10.1
SUBNET: 255.255.255.0
[code]....
View 1 Replies
View Related
Mar 6, 2011
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
View 1 Replies
View Related
Jan 29, 2013
Can a router using OSPF propagate that he is a router with default-information originate... at the same time when he got an own gateway of last resort to an IP-adress? If so, how? I can't get it to work.
View 8 Replies
View Related
Mar 23, 2013
I try to install a Gateway to Gateway VPN between a RV042G router (LAN1) and a 1721 router (LAN2). The VPN is connected. I can ping the devices from a LAN to the other in the two way.
But otherwise I can't access to the devices of LAN2 from LAN1 like with telnet, HTTP, mstsc, ....
And it is OK to access to the devices of LAN1 from LAN2....
Normally I access to all the resources of LAN2 with the Cisco VPN Client but i try to change it with this router. The firewalls are off on all the computers I look.
View 2 Replies
View Related
Nov 8, 2011
I have a RV042 and I am trying to setup a Client to Gateway VPN for about 12 to 15 remote users. These users travel a lot and need to connect to the server. I have never setup a vpn and have looked at the manual and set it up like it says to. I installed the Quick VPN client on the remote computer and copied the certificate to the remote computer.
I am having two problems.
1. When I run the client on the remote computer and try to connect it tells me the cert is not installed on the local computer. (it is copied to the root program directory C:Program Files Cisco Small Business and the sub directory, C:Program Files Cisco Small Business Quick VPN Client.
2. I can continue and it acts like it's connecting but it does not. If I look at the router VPN summary it shows that I connected for only a brief time.
View 1 Replies
View Related
Mar 31, 2013
I've got half a dozen RV042 routers in various locations. They are running v4.0.0.07. Seemingly randomly, I got the 502 Bad GatewayThe CGI was not CGI/1.1 compliant. error when attempting to log into the web interface with google chrome (same with IE too). This happens from the LAN side. I actually didn't notice it until my Opsview monitoring software threw up a critical when it didn't get an http response. The router is otherwise actually working just fine.Since the first occurrence, more of my routers have developed the same error.
I've tried different browsers, clearing caches, though I'm not surprised those efforts were fruitless, as there is clearly a problem even when no browser is involved (nagios). The nagios http check also returns a 502 Bad Gateway.
View 7 Replies
View Related
Feb 5, 2012
I'm having problems setting up VLANs on my RV110W Small Business Router. I have updated the firmware to the latest : 1.1.0.9 Here is my set up :
WAN settings :
IP : 192.168.1.252 / 255.255.255.0 - Gateway 192.168.1.254
VLAN1 (default) :
IP : 192.168.2.254 / 255.255.255.0
VLAN3 (test) :
IP : 192.168.16.254 / 255.255.255.0
Inter-VLAN routing option is checked.
Symptoms :
- The communication from VLAN1 to WAN is fine
- The communication from VLAN3 to VLAN1 is fine
- The communication from VLAN1 to VLAN3 is not working
My routing table is :Routing table Entry ListDestination LAN IPSubnet MaskGatewayInterface192.168.2.0255.255.255.0192.168.2.254LAN192.168.1.0255.255.255.0192.168.1.252WAN192.168.16.0255.255.255.00.0.0.0LAN0.0.0.00.0.0.0192.168.1.254WAN
As you can see, the gateway for VLAN3 is set to 0.0.0.0, which is wrong I believe. I don't know how to update that. I tried to add a a static route for the subnet, but the router did not let me do that.
View 1 Replies
View Related
Nov 6, 2012
I gave setup a vpn gateway between two cisco RV120W. The connection is established.
Active IPsec Security Association Table: Policy NameEndpointPacketsKBytesStateActionRxTxRxTxVPN-INTERDIO87.65.38.62000.000.00IPsec SA Established Poll Interval: (Seconds)
The problem is that there is no trafic. Even ping te remote internal nework is not working. For testing i have disabeld at both sites te firewall and have configured both with an access rule any to any.
View 1 Replies
View Related
