Cisco Routers :: Getting VPN Gateway To Gateway With NAT For Multiple Subnets / RV082?
Feb 11, 2012
I have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc). I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity.
Routing does behave as advertised, where all traffic does go to the main office. However, the 192.168.1.0 subnet in the branch office does not get internet connectivity. I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet. Is there a way to configure the RV082 router to provide NAT for all subnets?
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets? Can the RV082 be used as part of the final solution or are my RV082s a wasted expenditure?
Following is the configuration that I'd implemented, (real IP and IKE keys are bogus).
Gateway To Gateway
Remote Main Office
Add a New Tunnel
Tunnel No. 1 2
Tunnel Name : n1-2122012_n2-1282012 n1-2122012_n2-1282012
Interface : WAN1 WAN1
[code].....
View 2 Replies
ADVERTISEMENT
Feb 14, 2013
I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
View 2 Replies
View Related
Mar 9, 2012
New hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
View 2 Replies
View Related
Jan 24, 2012
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
View 1 Replies
View Related
Jul 26, 2012
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
View 1 Replies
View Related
Aug 9, 2011
My rv082 router protect link gateway is already activated. How do i change the key or activate it with a new activation key?The router dont have any link to change the key. I'm using v1-2 rv082
View 4 Replies
View Related
Aug 30, 2012
I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...
View 0 Replies
View Related
Jul 6, 2012
I picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
'TECHNICAL' SPECS
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
[URL]
View 7 Replies
View Related
Oct 17, 2011
Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?
View 1 Replies
View Related
Apr 11, 2013
I have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.
View 2 Replies
View Related
Apr 8, 2012
I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway. One location is a static IP Address. The other location is a dynamic IP address.
View 2 Replies
View Related
Mar 19, 2013
I am trying to set up a gateway to gateway VPN connection between a RV042G (central site) and a RV110W (newest firmware) which is used for presentation purposes on various customer's sites. The RV042G has a static IP. The RV110W has different IPs, depending on where it is used.
Basic VPN settings are clear to me (we have another VPN between two RV042G with static IPs). I set up the VPN connection on the RV042G wth the following settings for "Remote Group Setup":
Remote Security Gateway Type : IP + Domain Name (FQDN) Authentication IP by DNS resolved: mydomain.no-ip.org Domain Name: router12345
The value "router12345" is what I have configured in the RV110W as "Host name" in the network settings.
This configuration does not work so I am obviously doing something wrong. Do I have to use "router12345.mydomain.local" instead if I configured "mydomain.local" as the domain name in the RV110Ws network settings? For my tests the RV110W has a WAN-IP of 192.168.178.100 because it is located behind a DSL-Router. The external IP of this DSL-router is 178.0.x.x. The resolved IP from mydomain.no-ip-org is 192.168.178.100 but when I look in the RV042G log I see the requests coming withg the external IP (178.0.x.x). Is this the problem? The last message I see in the log is "no connection has been authorized with policy=PSK".
Or can I use "IP + Email Address (USER FQDN) Authentication" instead (where can I enter this email address in the RV110W?). Or do I have to use "Dynamic IP"?
View 1 Replies
View Related
Dec 19, 2012
I exchanged a RV042 v1.2 (Firmware 1.3.13.02) by a new RV042G v3. (Firmware 4.2.1.02).
My problem is now the following: The old RV042 established the Gateway to gateway VPN connection as soon as an IP- address of the remote location was requested. The new RV042G stays on „Waiting for connection“ all the time and does nothing at all. The connection works by clicking „CONNECT“ or by ticking Keep-Alive in the advanced tunnel settings but NOT automatically as before. Is this a firmware issue or have I to configure something additional?
View 1 Replies
View Related
Apr 9, 2012
I am struggling on a problem for over 2 weeks despite of various researches.
We have a Cisco router, then an ASA 5520 8.4(3).
The private interface of the ASA is connected to a switch, and so on connected to one interface of the router.
The private interface is as following : 129.88.63.253 255.255.248.0 (/21) =>
It is in the 129.88.56.0/21 subnet
Here is the part of the router config we are interested in :
!
interface Vlan32
ip address 129.88.63.254 255.255.248.0 (this is the tunnel default gateway configured on the ASA - 129.88.56.0/21 subnet)
ip address 129.88.71.254 255.255.255.0 secondary
ip address 129.88.75.254 255.255.252.0 secondary
ip access-group CVPN-depuis-129.88.56 in
ip access-group CVPN-vers-129.88.56 out
ip verify unicast source reachable-via rx allow-default
no ip redirects
mls rp ip
!
On the ASA, there is currently one default route for the tunneled traffic :
route Private 0.0.0.0 0.0.0.0 129.88.63.254 tunneled
As you can see, it's on the same subnet as the primary IP address of interface Vlan32 on the router.
The scenario is as following :
- we can connect to the VPN with the appropriate alias (LDAP connection), then we get an IP address in the defined range (it's a local ASA pool)
- the pool is : 129.88.71.0/24
- but, once we are connected, we can't do anything, because it seems like we don't have any network access
View 9 Replies
View Related
Jan 12, 2012
Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies
View Related
Mar 25, 2011
I have RV082 in many locations and it is working fine.One location I just starting to have problem with packet lose (50 to 60 %)I ping between two location which i am having problem.Gateway to Gateway shows no lose on packet (reply with 20ms avg.)but router to router will lose packet 50 to 60 %.
View 1 Replies
View Related
Sep 13, 2012
config setup
protostack=netkey
klipsdebug=none
[Code]....
View 3 Replies
View Related
Jul 11, 2012
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies
View Related
Feb 8, 2011
we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies
View Related
Mar 22, 2011
I have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
View 1 Replies
View Related
Apr 6, 2013
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies
View Related
Jan 29, 2012
Just bought 3 WRVS4400N, I wanted to setup gateway to gateway VPN. I followed the instructions on the WRVS4400N admin guide and VPN does not connect. I also downloaded the VPN setup wizard and that also did get the gateway connected. Everything seems to be correct. Do I have to enable anything else? Firewall setting?
Below is my config.
IPSec VPN Tunnel: Enabled
Tunnel Name: TUN01
Local Security gateway: IP only
WAN1 IP: 192.168.100.1
SUBNET: 255.255.255.0
Local Security type: subnet
LOCAL IP: 10.10.10.1
SUBNET: 255.255.255.0
[code]....
View 1 Replies
View Related
Mar 6, 2011
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
View 1 Replies
View Related
Oct 6, 2012
I'm sitting around 6-15 feet away from my wireless router, and I keep losing wifi. I end up having to right click on the wifi icon in the bottom right corner and click Troubleshoot Problems. The problem which is found and fixed is "The default gateway is not available." During the troubleshooting, Intel My Wifi Technology gets disabled and then re-enabled, and things usually start to work again.ometimes I have to unplug the router to re-cycle it to fix the problem.When this happens is inconsistent - sometimes when I'm actively working, other times when I return from being away from my machine.[CODE]
View 5 Replies
View Related
Feb 24, 2011
I am trying not to run before i can walk,.. so first thing I'm trying to do is ping out to a DNS server in the internet: 212.135.1.36 from my internal network.
- If I put a default gateway on my router, and set to 172.16.32.254 (Firewall Vlan100 interface) and ping,.. it works fine from my router.
- If put a default gateway on my switch below the router as 172.16.32.252 (VLAN100 interface of the router) and ping from the switch it doesnt work.
I assume its getting to the switch as I can ping the 172.16.32.252 from the switch so the router is dropping the packets... my question is why!?
Once this bit works,.. the intention is to route any external bound traffic that comes from VLAN100 to 172.16.32.254, external bound traffice from VLAN200 to 172.16.64.254 etc etc
[Code] .....
View 5 Replies
View Related
Jan 29, 2013
Can a router using OSPF propagate that he is a router with default-information originate... at the same time when he got an own gateway of last resort to an IP-adress? If so, how? I can't get it to work.
View 8 Replies
View Related
Mar 23, 2013
I try to install a Gateway to Gateway VPN between a RV042G router (LAN1) and a 1721 router (LAN2). The VPN is connected. I can ping the devices from a LAN to the other in the two way.
But otherwise I can't access to the devices of LAN2 from LAN1 like with telnet, HTTP, mstsc, ....
And it is OK to access to the devices of LAN1 from LAN2....
Normally I access to all the resources of LAN2 with the Cisco VPN Client but i try to change it with this router. The firewalls are off on all the computers I look.
View 2 Replies
View Related
Mar 5, 2011
I have 2 gateway over my network provider to connect to internet.like Gateway1="1.1.1.2" and Gateway2 = "1.1.1.3".but i have only one network adapter with one wire.now i want program to create "Virtual Network adapter" assigned to my real network adapter to set secondary Gateway to it, and use it by "ForceBindip".
View 3 Replies
View Related
Jan 24, 2012
I have 2 networks ,one is 135.7.31.0/24 for intranet to connect remote office gateway is 135.7.31.253. other is airtel broadband to (network 192.168.1.0/24)connect internet GW 192.168.1.1.both are connected in l2 switch(cisco cat exp500) now I assign 2 ip addresses and gateway in win xp PC with TCP/IP advance settings also set the different metrics for 2 networks , now problem is I cannot connect remote office and internet simultaneously, only one networks connect at a time,
View 3 Replies
View Related
Jun 8, 2012
I just moved into a new place and the cable company supplied me with a Motorola sbg6580 gateway and I have a netgear wnr3500l router with dd-wrt. because of location I have computers plugged into both devices (htpc and game consoles in the gateway, desktops in the netgear). how would i configure the gateway and router so everything sits on a single network AND the netgear with dd-wrt handling all the heavy lifting (port forwarding mostly)
View 2 Replies
View Related
Jan 22, 2013
Here's what I want to do with my RV042: I have a bunch of devices, including a server, inside my network at 192.168.1.100
I've set up VPN using PPTP. It works, but if my clients have their own remote DHCP set up to 192.168.1.x, they can't get to the server. If their home DHCP is 10.x.x.x., everything works
I am considering changing my internal network to something obscure.
My server has two NICs. So I thought, I why not set one address up to 10.x.x.x But the two nets can't ping each other. I tried using "multiple subnet" on the RV042, setting up 10.1.1.1, but no luck.
View 1 Replies
View Related
Aug 5, 2011
We have 4 RV 042 routers and cisco router at HQ, we have Site to Site VPN tunnels in between, All branch offices are connected to HQ via S2S VPN tunnels
10.10.1.0/ 24 HQ
10.10.2.0/24 Branch 1
10.10.3.0/24 Branch 2
10.10.4.0/24 Branch 3
10.10.5.0/24 Branch 4
now lets say i am branch 1, i can access 10.10.1.0/24 network but cant access 10.10.5.0/24 network, means i dont have branch to branch connection, it should be through HQ, means my RV042 at brnach should fwd all traffic to HQ for another branches also. Under VPN tunnel if i try to configure remote destination 10.10.0.0/21 its not allowing me it says network overlaping with local network, how i can sole it, I know how to do in cisco, we can permit those networks in access lists.
View 1 Replies
View Related
Aug 16, 2011
We have Point to point T1 environment where 3 additional WAN sites get internet access through our RV042. When we setup load balancing we have problems with https traffic, so we setup protocol binding for https and everything worked great from the local LAN. When trying to access https content from the remote LAN across the WAN the sites failed and I see no option to add additional subnets to the protocol binding. Is there a command line feature that supports adding additional subnets for protocol binding or is the local LAN the only option?
View 7 Replies
View Related
