I have 2 gateway over my network provider to connect to internet.like Gateway1="1.1.1.2" and Gateway2 = "1.1.1.3".but i have only one network adapter with one wire.now i want program to create "Virtual Network adapter" assigned to my real network adapter to set secondary Gateway to it, and use it by "ForceBindip".
View 3 Replies
Our work building currently has 2 separate DSL lines feeding into it, one on each end of the building. The reason for two lines was so each one would have its own bandwidth, thereby supporting more simultaneous users. There is a router connected to the DSL jack at each end of the building, broadcasting its own wireless network: let's call them Work 1 and Work 2.Is there any way for me to connect the Work 1 and Work 2 wireless networks, so that they appear to the end user as one contiguous network?
View 3 Replies View Relatedsetting up a simple internet plan for a place, but a LAN center needs crazy fast internet, faster than most large enterprise class offices that take up an entire floor or two. Otherwise there is too much lag in games like first person shooters. We are expecting to have 60 computers, plus people bringing their own gaming rigs from home and laptops as well, xbox, ps3 and other consoles, all accessing the internet at the same time to varying degrees, with no room for lag. There is a LAN center in california that has 200 or more computers and they pay for 9 t3 lines, which is thousands and thousands of dollars per month. Plus the initial equipment to set that up from what I can find on cdw is many thousands of dollars also. Something like 10,000 for a router with 4 expansion bays, and 4000-6000 dollars for a t3 expansion card, bringing the total to around 22-28,000 for equipment to do just 4 t3's. Plus the monthly cost. Since we don't need all of the traffic to be secured like a high end business class line like a t3, I was considering what it would be like, and how one would set up, having multiple cable internet lines coming in. They make cable wic cards for cisco routers. 4, 50meg cable lines would give us 200 down and 40 up but I don't know how to make that work without having multiple public ip's. I was thinking that if I did have multiple public ip's on the network I could just divide the computers up so that they are in groups, using all of the public ip addresses for gateways, so that the load is split pretty evenly, but still, there should be a more seamless way to do this, I just don't know what it is. At the rate for business cable internet, 4 lines would probably only cost around 700 dollars a month, which is much better than probably 5 grand a month for several t3 lines.
View 3 Replies View RelatedMy computer will only run on ethernet cable, the network can be found but only connects for a second, connects to the internet in and out, it gives the error, default gateway is not available, or problem with the wireless network adapter. The manufacturer is HP
Windows IP Configuration
Host Name . . . . . . . . . . . . : Owner-HP
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : cogeco.net
[code]...
I have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc). I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity.
Routing does behave as advertised, where all traffic does go to the main office. However, the 192.168.1.0 subnet in the branch office does not get internet connectivity. I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet. Is there a way to configure the RV082 router to provide NAT for all subnets?
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets? Can the RV082 be used as part of the final solution or are my RV082s a wasted expenditure?
Following is the configuration that I'd implemented, (real IP and IKE keys are bogus).
Gateway To Gateway
Remote Main Office
Add a New Tunnel
Tunnel No. 1 2
Tunnel Name : n1-2122012_n2-1282012 n1-2122012_n2-1282012
Interface : WAN1 WAN1
[code].....
I was looking at an XP system that has 4 user accounts. Two are limited accounts and two are admin accounts. The adapter is a DLINK DWA-125 USB adapter.When logged into one of the admin accounts, internet works fine. When logged into one of the limited accounts, internet works fine.If I switch to either of the other accounts, the adapter can't get an IP address. If I switch back to one of the accounts that works, I get an IP right away.
View 2 Replies View RelatedAm trying to understand how we can have multiple IP addresses on a single NIC and what are the restrictions on the same. If i can have two IPs from two different networks present on a single NIC, then why would i ever get a new NIC?
Also, i want to understand the concept of virtual IP and how it fits into this picture.
I have an older DELL power edge 2800. Currently we have 2 NIC's one for the WAN one for the LAN. I wish to increase my users access speed. Can I team and or bond up to Four NIC's on the LAN side and leave the single NIC for the WAN? I am having trouble finding any info on the net for pulling this off. I have 67 users and throughput is getting a little rough.
View 1 Replies View RelatedIs it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
My topologie is to connect IBM Mainframes into a Single Gateway Scenario. All the configurations in the machines are correct, and during a feel period of elapsed time we had the mainframe XCA/line/PU Station (Side DLSW) and the PU from CCU 3745 line (Single Gateway Side) both into ACTIVE state. The problem occured when we tried to INACT and ACT the mainframe VTAM lines; The lines, after this restart operation stayed in PCTD1 all the time. Searching the problem into DLSW's Border Router definitions, we observe that there are two Routers Serial Interfaces defineds with the same SDLC VMAC address (4000.3745.0000). Executing the DEBUG DLSW command was verified that there are the following messages:
00:39:07: CSM: delete group cache for 4000:3745:1, group 0
00:39:07: CSM: delete group cache for 4000:3745:1, group 0
00:39:07: DLSw: START-FSM (2147483685): event:DLC-CloseStn.Cnf state:CLOSE_PEND
00:39:07: DLSw: 2147483685 to dead queue
My question is, the ocurrence of these two delete group cache for the same Mac Address 4000.3745.1, group 0, means the mistake into maintain defined two Serials Interfaces with the same SDLC VMAC Address ?
The messages dispalynd the CONNECTED state never appears and iI think mus be something like that sample:
%DLSWC-3-RECVSSP: SSP OP = 8( CONQ ) from peer 10.17.2.198(2065)
DLSw: START-FSM (488636): event:WAN-CONQ state:CKT_ESTABLISHED
DLSw: core: dlsw_action_i()
DISP Sent : CLSI Msg : CONNECT.Req dlen: 16
[Code]...
I need to put a few cameras, without a server, on a static WAN ip address. Do I just assign them a static LAN ip address(for example 192.168.1.200), make sure the port they use is open, then type the WAN static ip address then colon and the last address? Like this.....I'm making up the WAN address....45.34.55.334:200
View 1 Replies View Relatedsome of the servers are not pinging from one switch but they are pingable from other redundant distribution switch. So I took the IP addresses from the redundant switch, with that I found MAC addresses from the access switch.But when I tried to see to which ports these MAC are addresses are connected to, multiple MAC addresses are resolving to the same switchport. like 5 MAC's are showing to 1 port and other 3 MAC's are showing to other port, like this there are many. All these MAC's belong to virtual servers.
View 11 Replies View RelatedI just want to keep one PC as a server and one switch connect to it (For LAN). I want to connect multiple client/screen to that server, so I can use single servers for multiple screen/client.(Client machine will not have any CPU, they will utilize servers memory.)
View 1 Replies View RelatedI currently have mutiple computers at my place. Once the computer turned on i want the option of which login for the current computer to use, it can login it current computer or the mutiples computer with their content/data all inside. So more like an computer linked. Example, it can only to A or B, A is the current computer data, while B have all the data of the different computer monitor datas, and if i login B it will show that current computer info. And same goes to the B computer, i can login to A or B on the B computer. What makes this very good is that, both the computer logins are sort of connected, for example if im on actual computer A, but logined to computer B and downloaded/changed some files/data on the B login, once i login on computer B to login B, the changes will apply even tho the changes are done in computer A.
View 1 Replies View RelatedI have six Cisco 300 Series switches in Layer 2 mode. They are all connected using ports in Trunk mode. These Trunks are tagged members of all VLANS.
I have one 300 series in layer 3 mode with IP address assigned to each VLAN.I would like to use one Internet gateway for multiple VLANS. This gateway has numerous IP ports that forward to internal ip addresses on various machines.
All i9nternal clients use their respective VLAN IP as their default gateway.The Layer 3 switch is connected to one of the Layer 2's using a Trunk that is a tagged member of all of the VLANS.
I understand how traffic routes from a client to its respective VLAN gateway. Where I am confused is how it routes from there to the Internet gateway? Internet gateway is 192.168.1.1.VLAN IP's are 192.168.2.1, 192.168.3.1, etc...
Should the Internet Gateway be patched into the Layer 3 switch or one of the Layer 2's using a separate "Internet" VLAN?
I have a i-ball 150M wireless-N ADSL2+ Router device in that , in the NAT tab, i have activated DMZ at my static ip with a private address 192.168.1.224 , so that that ip enabled device can be access to anywhere in public network.I want that using this single static ip , How to configure two private address devices in DMZ, so that both of ip enabled devices can be access in public network.
View 3 Replies View RelatedI have multiple campuses and a Central Admin...I've created Groups for all, except I need a few devices within Central to be available to the Campus Admins... (ie..a Cisco WCS System) How do I allow a device to be put into multiple NDG groups?
View 1 Replies View RelatedWe are in the process of installing time clocks at some of our sites around the USA. Our security department has asked that the time clocks be completely isolated from the rest of the network. The time clocks will be administered by ADP via a centralized firewall utilizing NAT. We have multiple subnets available at each site. Let me give an example to calrify what I would like to do. Example: Site A has 10.168.19.0 /24 user subnet and is configured for VLAN1 using 10.168.19.1 on the router as the default gateway. I would like to use subnet 10.168.20.0 /24 for the time clocks, configure it for VLAN2 and use 10.168.20.1 as the router gateway address for VLAN2. This should allow me to NAT one of our additional public IP addresses to the 10.168.20.1 gateway address thus completely isolating the time clocks from the remainder of the network. Problem is I have not done this before so I'm a little confused about how to configure it in the Cisco 3750 switches.
View 6 Replies View RelatedI have Cisco L3 3560G switch which directly connected with router . i have configured Vlan 2,3 on the switch and assign port 2 & 3 respectably. I want to management both vlan 2 & 3 from from L3 port g0/10 .
View 6 Replies View RelatedI am Implementing Cisco IP Routing (CCNP ROUTE FLG) book and right now I am reviewing IPv6 chapter. This part of OSPFv3 multiple instances over a single physical interface caught my attention
View 6 Replies View RelatedWe having ACS version 5.2 0.26 with Active/Standby. We need to integrate active directory with ACS. Domain name given by Server team was as xyzcompy.local. When I tried to resolve the same domain name I got five servers ip address against the same domain name. however we given the ip reachability to only for two servers. We we try to save we get error saying that "Can not resolve the network address".
So my questions are;
- does ACS should have ip reachaibility to all five servers
- does the username/password we entered in the ACS should have domain admin rights?.
- the given AD is configured with windows NTP [URL] but when we configured ACS as windows NTP it was taking local server as active NTP..?
When we check the ACS logs, we saw the following error;
in acsLocalStore:
AdminName=acsadmin, DomainName=qatarconvention.local, ADOperationResult=unable to create secured connection against AD server, switching to non-secured connection. javax.naming.CommunicationException: simple bind failed: qnccad02.xxxxconvention.local:636 [Root exception is java.net.SocketException: Connection reset],
in ACSADAgent;
32484]: INFO dns.findsrv FindSrvFromDns failed: res_query failed _ldap._tcp.xxxxconvention.local
Sep 4 12:43:20 acs01-cc4 adjoin[32484]: INFO cli.adjoin Join to domain 'xxxxconvention.local', zone 'null' failed.
I attached some screen print which saw the error and output of nslookup for the domain name.
I just bought a Linksys EA6500 (AC 1750). Now after a week, seems to stop rresponding at times and I am get 5+ MAC Addresses from 1 IP address. I have only one NIC installed and it is configured to have a static IP.
See attached screen capture. ( Server-PC, IP: 192.168.1.130)
Can we use single ospf process for multiple VRFs in Nexus 7k. If yes is there a document to show how ?
View 0 Replies View RelatedI have a Failover pair of ASA5550's running ASDM 6.2(5) and ASA 8.2(2). Originally they were setup with 2 context's and an admin context but one of the contexts has now been removed. I would like to now migrate to single mode before I go about patching them to the latest software.
View 4 Replies View RelatedI have a FTP server at my local network and i have natted the private IP with my Public IP using default FTP Port ( 21) , now i have created Diffrent FTP Account in my server using port 2121 and i am able to login using the private IP with port 2121 , now i want to nat with my public IP with port 2121 and i failed,
1) 125.x.x.x --------- 10.10.1.x : 21 ( Able to access from external network)
2) 125.x.x.x ---------- 10.10.1.x : 2121 ( not able to login from external network and able to login internally )
We are migrating from a nother brand to an ASA Cluster running 8.4.5
We have a web-server on an inside interface listening on a non standard port - 20111. We have created a static NAT translating the public ip to the private, so If I do http://public-ip:20111 it works. (we are using a seperate public IP for this service only).
Now I need to create a NAT rule that will forward requests on BOTH port 80 and 443 to the same private ip and the same port number (20111)
The Private address is 10.99.250.20 and the "public" (I've replaced it in this example) is 172.16.16.16 I have managed to create a NAT that will translate 443 to 20111:
object network 10.99.250.20 nat (Private-DMZ,Outside) static 172.16.16.16 service tcp 20111 https
But if I try to add another rule like: nat (Private-DMZ,Outside) static 172.16.16.16 service tcp 20111 http It will simply replace the first one.
Is it possible to redirect both 80 and 443 from outside to the same port number and same IP on the inside?
I have a Fail over pair of ASA5550's running ASDM 6.2(5) and ASA 8.2(2). Originally they were setup with 2 context's and an admin context but one of the contexts has now been removed. I would like to now migrate to single mode before I go about patching them to the latest software.
View 2 Replies View RelatedI have two 1142n LWP ap converted into standalone, as client doesn't have any controller there. They just want to extend their network via wireless.
L3 switch (trunk port gig 1/48) -----> connected to AP1
L3 switch (trunk port 2/48) -----------> connected to AP2
client is looking for 3 vlans on the floor ( users might multiple vlans might associated same AP ). They have a dedicated DHCP/DNS server and he will be configuring 3 vlans on L3 switch with correct ip helper address on SVI interfaces.
I'm i allowed to created 3 SSID's on 1142n standalone AP ?
What would the various optiosn to achieve this requirement ? Is there any simplest way to achieve this ? Do i need to go for 802.1x ? I remember client told their users are authenticating by using AD for wired network. This is their first request for wireless environment
I read from this forum some discussion about the WLC VLAN Select feature. [URL]. I see that you can use this feature to have multiple VLANS (interfaces) to map to the same WLAN (SSID).
What I try to learn is under what scenarios would people need to have mutliple vlan mapped to single SSID?
In my environment, I have 50+ AP int he campus on 20+ Cisco 4500 switches. I have single WLAN and it is mapped to one subnet. All wireless users would be on that subnets, whereas wired users are on 20+ subnets of their own.
I have a facebook account for work and another one personal, and another one for my family, sometimes it's distrubing to log in into the 3 accounts at once, is there any solution how to log into the 3 accounts using a single Skype ID? or a chat webpage such as meebo before instant chat which acquired by google on the 11 of july 2012, I used to log in meebo using my 2 MSN accounts an 1 yahoo account at once, it was a great one indeed?
View 1 Replies View RelatedI have a customer with three rooms where teh access layer aggregation switches are run back to.
Access Switch Stack A -> room 1 + room 2
Access Switch Stack B -> room 2 + room 3
Is it possible to have three Nexus 7000s ie one in each room (1,2 and 3) and have them setup like this:
Nexus 7000#1 vPC domain 1
Nexus 7000#2 vPC domain 1 + vPC domain 2
Nexus 7000#3 vPC domain 2
Thus gving all access switch stacks redundant links to the core withouit spanning tree.
I know its not ideal but its a campus site and thats how the existing fibre runs go.
I am learning the 2911 router. Is there a way to set a physical single RJ45 port to handle multiple WAN IPs? Or do I need to buy a port expansion module.
View 12 Replies View RelatedI would like to know if it is possible to assign a 3rd IP address to my end user vlan. Basically the 45xx acts as my end user gateway and has been confirgured as below
interface VlanXX
description Main Vlan
ip address 2.X.X.X 255.255.255.0 secondary
ip address 1.X.X.X 255.255.252.0
[Code].....
Here, due to IP address exhaustion in my end-user network, i want to add one more subnet X.X.X.X/22 to my network and assign one IP more from this range to the above vlan to act as the gateway IP.
