I just bought a Linksys EA6500 (AC 1750). Now after a week, seems to stop rresponding at times and I am get 5+ MAC Addresses from 1 IP address. I have only one NIC installed and it is configured to have a static IP.
See attached screen capture. ( Server-PC, IP: 192.168.1.130)
I currently have my EA6500 behind verizon fios router. I have 5 static IP addresses assigned to FIOS router, however the machines I want to connect to are behing EA6500. It's a dual NAT scenario:
Public IP - FIOS Router - 192.168.1.0/24 network - EA6500 - 192.168.2.0/24 network
What I would like to do is for each public IP address, I would like to forward traffic to a particular host on 192.168.2.0 network. I can easily configure FIOS router for static NAT and assign one internal IP (from 192.168.1.0 range) for each public IP. However, I don't see a way to assign multiple IPs from 192.168.1.0 network to EA6500 internet interface.
I don't want to use EA6500 as a bridge as it will pretty much reduce my EA6500 to a very expensive GigE switch.
Is this possible? Or should I replace it with something more useful like a business router? This is for my home so I would like to avoid buying an expensive business router.
I have verizon fios business line with 5 static IP addresses and am configured for ethernet wan. I can use EA6500 as the router instead of using Verizon's own router, however I can't figure out how to assign all 5 static IP addresses on internet interface. I have already assigned first IP to internet interface but don't see a way to add more IPs either in internet interface or from NAT section where I can create static NAT.
Is this even possible with EA6500? If so, how?
I need to put a few cameras, without a server, on a static WAN ip address. Do I just assign them a static LAN ip address(for example 192.168.1.200), make sure the port they use is open, then type the WAN static ip address then colon and the last address? Like this.....I'm making up the WAN address....45.34.55.334:200
View 1 Replies View RelatedI have my other XBOXs connected to a 24 port switch but the one connected to the ea6500 directly gives me this moderate NAT issue. I thought this new router would be an upgrade to my old dlink but so far I get a new problem every day.I have reserved dhcp addresses for all the boxes and set up port triggering for the ports listed in several guides. But what else do I need to do? Is it likely I got a bad router?
View 2 Replies View Relatedhow do I block IP/Internet Adresses for ALL users without adding the sites manually per user in the Parental Control panel? I want to block a certain IP/internet adress for all users but can't find this feature within my EA6500 anywhere?Is this a firmware bug? Has linskys forgotten that some sites want to blocked for all users and how do I do it all in one?
View 1 Replies View RelatedI got the new EA6500. For the last few days I've noticed there are multiple devices showing under one device with different IP addresses. In the beginning they show up individually with their own device names, then somehow combine. Each device is different ie. computer, phone, DirecTV box, etc. I did a hard reset, re-flash and still it keeps happening.
View 9 Replies View RelatedOnce your devices start showing up in your device list make a DHCP reservation for each device. (after confirming that no other devices are listed under it).
If you have a device that has multiple MAC & ip addresses under it you MUST first determine what the devices are listed & power-down before you can delete the device. Also note that some wired devices will still show as connected so you must have to either power down the device by pulling Th power cord OR disconnect the ethernet cable.
Is it possible to have multiple public IP addresses that are from different subnets going through one router? I have been told that this is not possible with most routers and that I would have to spend a lot of money on a router to be able to do it. I am still not totally clear on what defines a subnet even after reading up on them. What I am trying to achieve:
-My office has 10 computers.
-All would be connected to one router.
-My internet service provider has provided me with 10 public IP addresses, that are all very varied (which I asked for)
We are in the process of installing time clocks at some of our sites around the USA. Our security department has asked that the time clocks be completely isolated from the rest of the network. The time clocks will be administered by ADP via a centralized firewall utilizing NAT. We have multiple subnets available at each site. Let me give an example to calrify what I would like to do. Example: Site A has 10.168.19.0 /24 user subnet and is configured for VLAN1 using 10.168.19.1 on the router as the default gateway. I would like to use subnet 10.168.20.0 /24 for the time clocks, configure it for VLAN2 and use 10.168.20.1 as the router gateway address for VLAN2. This should allow me to NAT one of our additional public IP addresses to the 10.168.20.1 gateway address thus completely isolating the time clocks from the remainder of the network. Problem is I have not done this before so I'm a little confused about how to configure it in the Cisco 3750 switches.
View 6 Replies View RelatedIs it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
I have two 1142n LWP ap converted into standalone, as client doesn't have any controller there. They just want to extend their network via wireless.
L3 switch (trunk port gig 1/48) -----> connected to AP1
L3 switch (trunk port 2/48) -----------> connected to AP2
client is looking for 3 vlans on the floor ( users might multiple vlans might associated same AP ). They have a dedicated DHCP/DNS server and he will be configuring 3 vlans on L3 switch with correct ip helper address on SVI interfaces.
I'm i allowed to created 3 SSID's on 1142n standalone AP ?
What would the various optiosn to achieve this requirement ? Is there any simplest way to achieve this ? Do i need to go for 802.1x ? I remember client told their users are authenticating by using AD for wired network. This is their first request for wireless environment
I read from this forum some discussion about the WLC VLAN Select feature. [URL]. I see that you can use this feature to have multiple VLANS (interfaces) to map to the same WLAN (SSID).
What I try to learn is under what scenarios would people need to have mutliple vlan mapped to single SSID?
In my environment, I have 50+ AP int he campus on 20+ Cisco 4500 switches. I have single WLAN and it is mapped to one subnet. All wireless users would be on that subnets, whereas wired users are on 20+ subnets of their own.
I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
I have a situation where a user needs more than one office extend AP in his home. My office extend controller is a 5508 running 7.0.220.0. Are there any issues NATing multiple OE APs to a single address? My initial lab results indicate that each of the AP's associate with the controller and establish a DTLS tunnel. I see the SSIDs get pushed to the AP and then it seems to restart the process never being fully operational. Is there a workaround that will allow me to run mutliple OE APs?
View 12 Replies View RelatedI would like to know how to setup QOS on the linksys EA6500 wireless router. I know about the media prioritization settings, however, thats not enough for me. I would like to setup upload and download speed limits for certain devices on my network, like, say 300kbps download for a certain device at all times.
View 3 Replies View Relatedprovide me with the latest (or one) release of 1.1.27 firmware for the EA6500. I am deeply disappointed in the last firmware upgrade and due to security and sudden lack of certain, or let's say all, functionality in bridge mode I need to downgrade or wait for an upgrade where that's fixed, but most likely not soon, or ever. Where could I find the firmware downgrade.
View 2 Replies View RelatedI use EA6500 I Don't find WOL OTL..
View 1 Replies View RelatedI was wondering if it's possible to use two EA6500 in the same network, one as main router and the other as anacess point?
View 2 Replies View RelatedI have an EA6500 which obviously has 4 Gigabit ethernet ports for my home network, but I need a DSL modem to get it working.What's the maximum speed current modems can supply from the Internet to my router, is there such a thing as a Gigabit capable DSL modem these days or am I dreaming ? Is it possible to even get Gigabit dowload speeds via DSL or would I have to go cable to achieve something like that ?My main concern is I don't want to buy a modem that will slow down or 'throttle' the capabilities of the new router I've just purchased or have I got the wrong idea ?
View 7 Replies View RelatedLooking to upgrade my old G router to the EA6500. I don't see anything about VPN pass through on the EA6500 or any linksys N router. Is this feature something they no longer include?
View 3 Replies View RelatedI would like to use the EA6500 in my network - but nor as primary router (or in fact routing at all). I would have thought, one could simply tell the device to use a particular gateway, but it does not seem to be easy. I have used many other home routers as combined switch/AP/USB-drive (latest a D-Link DIR-655), but the EA6500 seems very picky. The "easy" "Smart Wi-Fi" setup requires internet access through the WAN port - and that divides my home network, which then have two zones which cannot really "talk" to each other. Alternatively, I can reset the device and access it directly on the IP (initially 192.168.1.1). But then I can change only LAN and WLAN settings. Stuff like Guest Access, USB-devices etc. won't work. Do anybody have success with this device without using the WAN port and the DHCP server?
View 8 Replies View RelatedI have a new EA6500 and am failing at getting ftp to work. I have updated the firmware.My ftp folder is on a Seagate USB Go-Flex drive attached directly to the router via USB. I have set up shares which I can see and access via my computer which is attached to the router.FTP is configured to use port 21 and UTF-8.
View 9 Replies View RelatedI have a pair EA4500s that I am swapping out for a pair of EA6500s. One EA6500 is a router. The 2nd EA6500 is set as a bridge and us being used as an Access Point about 200ft and two floors above the main EA6500 router. The two units are connected via DECA (200MB Ethernet over DirecTV cable - an alternative for others with a cable provider is called MOCA). So, basically two EA6500s serving as two Access Points on opposite sides of the house and all wireless networks on different channels but all sharing the same SSID. Everything works GREAT except for one unusual issue.
The issue is with wired or wireless clients. If I try to use my PUBLIC address with port number to address a local client on the local network inside the NAT network the NAT redirection fails. In other words if I use 172.16.16.8 for a local web cam while inside my network from an iPhone or PC all works great. If I use the external public address, however, the connection times out. If I pop out the EA6500 doing the routing/NAt and swap it with the old EA4500 with basically the same config as the EA6500 everything works again. The EA6500 and the EA4500 are configured identical for the most part and with the EA4500 as the main router NAT redirection works great but with the EA6500 NAT redirection fails. I have the firewall setting to FILTER NAT REDIRECTION unchecked so that's not the problem.
Seems very odd.... and only seems to happen with the EA6500..... the work around is to use the local IP address when the client is on the inside and the public address when on the outside, but what a pain that is....
Any work around to enable reverse NAT or similar functionality on the EA6500? I recently upgraded from a Dlink that did support reverse NAT to my internal devices through a dynamic dns service. Now I have to know the IP address for all the devices.
View 1 Replies View Relatedi setup my new EA6500 with the ethernet cable from my cable modem plugged into the EA6500, but with my old E4200 still switched on, but disconnected, i seemed to have ended up with a ip address of 10.250.27.47, not the 192.168.1.1 i was expecting, which i had with the E4200, my question is, is 10.250.27.47 something i should expect with the EA6500, or do i need to do a factory reset on the EA6500 and start again with everything else switched off as a precaution ?
View 6 Replies View RelatedI set up EA6500. All kinds of problems with anything on the 2.4 MHz band. My wireless desktop on the 5.0 MHz band was flawless. So I ran Xirrus Wi-Fi Inspector (freeware). The router is transmitting two 2.4 MHz signals! One is the SSID I set up and named. The other one is identical in every way except that the BSSID is slightly different. It is a non-broadcasted SSID that shows up on every device as "Other Network." I was on the phone with Cisco Support tonite, and they were great as usual but had no answer. If you change the channel on the 2.4 MHz band, the shadow network also changes to the same channel (this blew the Tech's mind). We reset the router to factory settings and started over. They are calling me back tomorrow. This router has great features on paper, but so far, it has not delivered.
View 5 Replies View RelatedThe only way I could get my EA6500 to work as auto DHCP to my Roadrunner Motorola SBV5220 Surfboard cable modem was to disable IPv6 support on the router. It appears that the EA6500 attempts to issue the DHCP request for address assignment from the modem using IPv6. I could see the status of "Connecting" for IPv6 in the Diagnosis Reports and it would hang. Once I disabled IPv6, the modem assigned an IPv4 address and everything worked fine. However, am I giving up any functionality by having to do this? I bought this router and the WUMC710 Universal Media Connector for the 5GHz connectivity for streaming and just wondered if I'm impacting UMC performance or any other functions of the router by having to disable IPv6.
View 1 Replies View RelatedI am interested in running the EA6500 without all the Cloud Connect software etc. Is this possible? Is there a basic way to set this up without that requirement?
View 1 Replies View RelatedI just bought the EA6500 last week. Had to RMA it on Monday and got the new one today. The issue still persists. The power light is constantly blinking and my computer is unable to obtain an IP address from it. I contacted tech support and was unable to get the issue resolved so I had it exchanged believing it was defective. The new one does the same thing. When I connect my computer to it, the light on my Ethernet port stays a solid orange instead of green like it does for my usual router. The Cisco light is constantly blinking.
View 9 Replies View RelatedI have two USB drives connected to my EA6500. When I use the ip to connect to them everything works just fine, but I cant map the drives. If I access map drives, I cant do anything with the files. It looses connection all the time.
View 2 Replies View RelatedI've noticed that my pings on all my devices go up when I enable QOS.This even happens on the PC which has high priority.The ping times go up by an average of 6ms, so if I normally have a 14 ping to a host it will now be 21.I've tested this by turning media prioritization on and off and everytime its turned on this seems to happen, although sometimes it requires a router or pc reboot before the issue arrises.
View 8 Replies View RelatedI have it set up as Capri (2.4 GHz) and CapriHD (5 GHz). CapriHD was intended only for HD video traffic. My wife's iphone 4S can only use 2.4 GHz, and it suddenly quit connecting after 1-2 months of use. My iphone 5 can use either band and it can only connect on 5 GHz. This problem MIGHT correspond to the recent firmware upgrade? I was traveling a lot around that time so can't be sure that is a culprit.Really thought the problem was the hardware, so I replaced it with a new EA6500 and getting the same result.
View 2 Replies View Related
