I have multiple campuses and a Central Admin...I've created Groups for all, except I need a few devices within Central to be available to the Campus Admins... (ie..a Cisco WCS System) How do I allow a device to be put into multiple NDG groups?
View 1 RepliesIs it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
I'm working with a 1113 ACS device running the 4.2.0.124 software. I'm trying to get multiple network device groups to use an existing Remote Agent set up for authentication against our Windows domain. For instance, we want our infrastructure switches to authenticate agains the local Active Directory and our WLC to authenticate users agains the same Active Directory. When I try and set both network device groups to use the same remote agent, it fails and reports either the host name is already in use or the IP address overlaps with an existing remote agent.
The question is:
Can I have multiple network device groups use the same remote agent? Or do I have to install the remote agent software on separate Windows servers in order to have different types of devices authenticate against the Windows AD?
We have multiple RA VPN groups on a 3845 router.RADIUS authentication is currently happening between the 3845 and a single Windows 2008 server. We have a specific windows group that AD users are members of, and they are allowed to connect via VPN.
I'm creating a new RA VPN Group, which should only allow different AD users. Is it possible to create another RADIUS association to the same server, or do I need to authenticate against a different Windows server?
I have ACS 5.2 running as a VM. I'm AD, then local authentication successfully for device access, but I want to define ACS user groups to restrict login. I don;t see any way to do this. If I use AD groups, they don;t show up as selection options on the policy screens, just the ACS locallyy defined groups.
View 1 Replies View RelatedI am using ACS 5.3 What I am about is setting user authentication against existence of the user in specific AD group, not just being a member in any AD. What is happening now, users get authenticated as long as they exists in the AD, luckily they fail on authorization, as it is bound to specific AD group.
how can I bind the authentication aginst specific group in AD, not just using AD1 as the identity source.
3750 can not support multiple subnets in it's DHCP server pool config.
Is this an issue that can be fixed with a different iOS or is there a different Cisco switch that I can replace the 3750 with that will handle multiple subnets within an individual pool?
We having ACS version 5.2 0.26 with Active/Standby. We need to integrate active directory with ACS. Domain name given by Server team was as xyzcompy.local. When I tried to resolve the same domain name I got five servers ip address against the same domain name. however we given the ip reachability to only for two servers. We we try to save we get error saying that "Can not resolve the network address".
So my questions are;
- does ACS should have ip reachaibility to all five servers
- does the username/password we entered in the ACS should have domain admin rights?.
- the given AD is configured with windows NTP [URL] but when we configured ACS as windows NTP it was taking local server as active NTP..?
When we check the ACS logs, we saw the following error;
in acsLocalStore:
AdminName=acsadmin, DomainName=qatarconvention.local, ADOperationResult=unable to create secured connection against AD server, switching to non-secured connection. javax.naming.CommunicationException: simple bind failed: qnccad02.xxxxconvention.local:636 [Root exception is java.net.SocketException: Connection reset],
in ACSADAgent;
32484]: INFO dns.findsrv FindSrvFromDns failed: res_query failed _ldap._tcp.xxxxconvention.local
Sep 4 12:43:20 acs01-cc4 adjoin[32484]: INFO cli.adjoin Join to domain 'xxxxconvention.local', zone 'null' failed.
I attached some screen print which saw the error and output of nslookup for the domain name.
As we all know, MS has changed the default workgroup names in different versions of windows. Additionally, you can rename your workgroup anything you like. I have XP, Vista, and Win7 computers, a television, BluRay player, a Wii, two printers, and a NAS with two USB drives attached. All of these -except the Win7- are wired to one of two switches. I have wireless: iPad, the Win7 notebook, Nintendo DSs. I have friend, and non-friend machines (computers, tablets, and phones) that come and go that are wired or wireless. The 3 windows computers all have the same workgroup name. All of my other units do not use workgroup names. I have a router, and two unmanaged switches, and have, on occasion, a second router. The main router, which has wired, and dual band wireless (each with two named wireless networks) nets, sees everything, by name and/or MAC address. Win7 is blind, deaf, and dumb.: it shows its own workgroup name, but no other workgroup name(s) , and, consequently, no unit on these other workgroups. It will show some wired units not in a workgroups - the television, and the printers (not the Wii or NAS). It will not show the wired XP computer! No wireless units either in workgroups or not in workgroups appear. Additionally, Win7 only shows units on its wireless network, not on the other three. The wired units it does show are not on any of the wireless networks, though it lists them on its wireless network.I have left the Homegroup, and terminated the Homegroup services. I have allowed discovery, and unlimited sharing of everything on every computer on the router, and yet the Win7 unit does not share or see well at all.Why?
View 2 Replies View RelatedI have 2 routers ( Cisco 3845's) both running identical IOS's. Each router has identical 5 networks on it with one network each being different.I have HSRP set up on the identical 5 networks.Your standard Fail over senario.ON one of the routers one network is not seeing the other router in the same network, Will not Ping or traceroute.And HSRP stopped working ( both were thinking they were active. which of course brought the network to a halt. Non of the interfaces has any ACL on them, They are plugged into a Brand new Cisco 3560v2 switch. I have switches out the cables to eliminate that as an issues.
View 1 Replies View RelatedI currently have a content group as follows;
content My_Group
add service blade1
add service blade2
add service blade3
vip address 1.2.3.4
advanced-balance arrowpoint-cookie
[code]...
So I have 3 blades which are proxy servers and user go first to an MS ISA server then the VIP of the CSS and then the rules processes them give them a blade and chuck them out onto the Internet.
I want to leave the above rule, but remove one blade create an additional content group with that blade and have it process requests for a particular site so, I would create the following
content My_Group2
add service blade3
vip address 1.2.3.4
advanced-balance arrowpoint-cookie
[code]...
So my question is can I do that having the same VIP's etc so if a request comes in and it matches www.thewebsite.com that the second content rule matches it 'better' and therefore processes it or would it still be caught by the "/*" content group. I don't want to create more VIPS as I have a real ache getting firewall rules done.
We are in a warehouse type setting and have data centers on each side of warehouse with 5508 WLC's in each data center. Each side is on its own subnet with routing in between and a different set of SSID's for each set of WLC’s. Are goal is to have the ability to failover in the event that if one data center goes down AP’s will move to the controllers in the other DC and the clients will still be able to operate.
Our thought was to implement mobility groups between the controllers. While I saw documentation on setting this up when the controllers are on the same vlan, I didnt see any setup config when controllers are in different vlans. So I am wondering if mobility groups are even an option for what we want to accomplish. For the most part clients stay on their respected sides of the warehouse and so we are not necessarily needing roaming for clients between controllers in DC1 and DC2. But that does raise another question in that we do have a planned voice wlan that we would like to have the ability to roam between each side of the warehouse. But we have seen ip issues with this. In the past we have had both SSID's setup on each side and ran to issues with clients not renewing their IP address when moving to the controllers on the different subnets.
Can we setup mobility groups between controllers on different vlans/subnets? For failover purposes will mobility groups assist in our setup with 2 DC’s and different subnets/vlans? If the answer is yes we can setup mobility groups between different subnets, is there a way to setup the SSID's on all controllers and have the ability for clients to roam and renew their IP’s when moving to a different controller on a different subnet?
i have a question about multiple TACACS Groups. I want to archive the following:
A Cisco 888 is managed by me and a Provider Support Team. Since we both want to access our own TACACS Server, i want to create two TACACS Groups. Is it possible to me, to bind a Tacacs Group to one Interface, and the second TACACS Group to another ? Means that our stuff is connecting to the LAN Interface FastEthernet0 that is applied to the SVI in V LAN 1.
The service technicians from the Provider are connecting to the external Interface or through a possible Lo. (another IP). I do not want to mix our 2 TACACS+ Server and theirs together in one Group. So have anybody tried this before ?
I've run into an annoying issue with my ACS 5.2 install. I can no longer add directory groups in the AD settings, the ACS comes back with "The item you are trying to delete is referenced by other items.You must remove all references to this item before it can be deleted." but I am not deleting any group, just adding.
Could probably be cleared with removing the AD setup completely, which for obvious reasons is not something I want to do.
We are running two ACS appliances but we cannot figure out how we can add a user into 2 differents groups.Here's the context :We have a company A which is having devices, this company uses Group A.then we have a company B which is having devices, this company uses Group B.But the admin has to manage the devices for both companies A & B.We don't want to mix devices from company A with company B.Is there a way to add the user into both groups A & B.
View 5 Replies View RelatedAfter clicking on below path we are not getting option as should be reflected. Below is the snapshots for the issues.
Access Policies > Access Services > Default Device Admin > Identity
I have seen similar references to this issue, but no concrete solutions. My new ACS appears to join my domain with little or no issues, however, when I go to list the groups nothing is ever listed.Running ACS as a vm.I have set the ntp server on the ACS server to match my domain.I can ping all domain controllers/DNS servers.nslookup resolves hostnames of my domain controllers
***Update***
I verified that a computer account for my ACS is in fact being created, however, I am receiving some Kerberos errors on my DC with the FSMO roles:
Event Type: Error
Event Source: KDC
Event Category: None
Event ID: 26
Date: 8/5/2011
Time: 3:07:46 PM
User: N/A
Computer: <MY DC>
Description:While processing an AS request for target service krbtgt, the account <ACS SERVER> did not have a suitable key for generating a Kerberos ticket (the missing key has an ID of 1). The requested etypes were 17. The accounts available etypes were 23 -133 -128 3 1.
I have an ACS 5.1 and am trying to integrate with windows 2008 R1. The ACS has a valid AD account and indicates that its connected but when I try to list any directory groups my windows IE browser hangs?
View 2 Replies View RelatedI've configured three specific AD groups, Admin, Storage, and HelpDesk, with their own commands sets.
This seems to be working fine, but everyone can log into everything, but they can't do anything except exit.
My goal is to not allow anyone to login that is not part of the three AD groups I have specified with the respective command sets.
All the logins hit the Admin account, even though the id in AD is not in the that AD group. I have something screwed up.
Recently I've been working with the ACS 5.2 (Installed on VMWare). At the beginning I was using a Win Server 2003 Enterprise edition AD, and there was no problem with the AD and the CA Authority. Because some of my customers use Win Server 2008 I change the AD platform to Win Server 2008 Enterprise edition (x64).I don't really have a great experience with Win Server Platforms and, for what I've seen, the Win Server 2003 Services deployment is easier than the Win Server 2008 is.
So, when I used the Win server 2003 I could not only synchronize the ACS with the AD but also use some groups created on the AD to perform the Network Access Authentication. When I try to do the same with the Win Server 2008 AD the ACS and the Server get Synchronized but when I want to add the groups for the Authentication purposes there is no one, absolutely nothing... so I cannot do any test.Also I looked for information about the compatibility between the ACS 5.2 and the Win Server 2008 platforms and at the end the platforms are compatibles.
I have been tasked with migrating from ACS 4 to ACS 5.3. I havent had any training and so i am finding it a bit different. Currently i have this issue -
I have a group in the ACS 4 for users accessing via wireless on the ACS - Code...
We have ACS Engine 4.1 and want to upgrade it to 5.x.
Is the new version of ACS 5.2 allows a user to belong to several groups of AD ?
I'm trying to setup ACS 5.2 with an ASA v8.3.2 to lock users into VPN groups based on a users AD group. I've tried various combinations but the group lock isn't working. I've done steps 1 & 2 ...
1) Network Devices and AAA Clients -> Define VPN
2) Users and Identity Stores -> Setup AD and Directory Groups, test connection
Policy Elements:
Q1) Policy Elements - Do I need an authorization profile for each group:
Q2) What RADIUS attributes should I use to match my ASA tunnel-groups?
RADIUS-IETF attribute 25?RADIUS-Cisco VPN 3000/ASA/PIX 7.x 85 (Tunnel-Group-Lock)?Other?
Access Policies:
Q1) Do I need to enable and use group mapping?
Q2) Do I need a Network Access Authorization Policy for each group?
I am trying to set up RA VPN on ASA 8.4 with 2 groups - VPNGp1 and VPNGp2. VPNGp1 users will access 1.2.3.0/24 and VPNGp2 users will access 5.6.7.0/24. User authentication will happen using ACS 5.3 Radius.
On ASA, I have configured the IP pools, VPN ACLs, VPN groups, group policies for each group, and tunnel groups.
On ACS, I have created vpn-user1 and vpn-user2 for each of 2 groups.
I am not sure if some more configuration needs to be done on ASA and ACS... Do I need to add new users - vpn-user1 and vpn-user2 - on ASA, under each corresponding group policy, using vpn-group-policy command? Or I need to do something else on ACS?
Lastly, how can I configure authorization and accounting for the VPN users? Do I need to do this on ACS or on ASA?
Am trying to understand how we can have multiple IP addresses on a single NIC and what are the restrictions on the same. If i can have two IPs from two different networks present on a single NIC, then why would i ever get a new NIC?
Also, i want to understand the concept of virtual IP and how it fits into this picture.
I have an older DELL power edge 2800. Currently we have 2 NIC's one for the WAN one for the LAN. I wish to increase my users access speed. Can I team and or bond up to Four NIC's on the LAN side and leave the single NIC for the WAN? I am having trouble finding any info on the net for pulling this off. I have 67 users and throughput is getting a little rough.
View 1 Replies View RelatedWe are running ACS 4.0 so understandably so we are looking to upgrading to a Cisco supportable version of ACS. The limitation of our current version of ACS does not support nested AD groups. The latest version of ACS (I think it is 5.4) will?
View 1 Replies View RelatedI need to put a few cameras, without a server, on a static WAN ip address. Do I just assign them a static LAN ip address(for example 192.168.1.200), make sure the port they use is open, then type the WAN static ip address then colon and the last address? Like this.....I'm making up the WAN address....45.34.55.334:200
View 1 Replies View Relatedsome of the servers are not pinging from one switch but they are pingable from other redundant distribution switch. So I took the IP addresses from the redundant switch, with that I found MAC addresses from the access switch.But when I tried to see to which ports these MAC are addresses are connected to, multiple MAC addresses are resolving to the same switchport. like 5 MAC's are showing to 1 port and other 3 MAC's are showing to other port, like this there are many. All these MAC's belong to virtual servers.
View 11 Replies View RelatedI just want to keep one PC as a server and one switch connect to it (For LAN). I want to connect multiple client/screen to that server, so I can use single servers for multiple screen/client.(Client machine will not have any CPU, they will utilize servers memory.)
View 1 Replies View RelatedI currently have mutiple computers at my place. Once the computer turned on i want the option of which login for the current computer to use, it can login it current computer or the mutiples computer with their content/data all inside. So more like an computer linked. Example, it can only to A or B, A is the current computer data, while B have all the data of the different computer monitor datas, and if i login B it will show that current computer info. And same goes to the B computer, i can login to A or B on the B computer. What makes this very good is that, both the computer logins are sort of connected, for example if im on actual computer A, but logined to computer B and downloaded/changed some files/data on the B login, once i login on computer B to login B, the changes will apply even tho the changes are done in computer A.
View 1 Replies View RelatedI'm using cisco LMS 4.0, I've discovered the device and next plan is to collect the device configuration.I would like to know, How I can collect the configuration for single device.What configuration changes required on my LMS & Cisco device.
View 1 Replies View RelatedI have 2 gateway over my network provider to connect to internet.like Gateway1="1.1.1.2" and Gateway2 = "1.1.1.3".but i have only one network adapter with one wire.now i want program to create "Virtual Network adapter" assigned to my real network adapter to set secondary Gateway to it, and use it by "ForceBindip".
View 3 Replies View Related