Cisco Application :: CSS 11503 - Multiple Content Groups?
Oct 4, 2011
I currently have a content group as follows;
content My_Group
add service blade1
add service blade2
add service blade3
vip address 1.2.3.4
advanced-balance arrowpoint-cookie
[code]...
So I have 3 blades which are proxy servers and user go first to an MS ISA server then the VIP of the CSS and then the rules processes them give them a blade and chuck them out onto the Internet.
I want to leave the above rule, but remove one blade create an additional content group with that blade and have it process requests for a particular site so, I would create the following
content My_Group2
add service blade3
vip address 1.2.3.4
advanced-balance arrowpoint-cookie
[code]...
So my question is can I do that having the same VIP's etc so if a request comes in and it matches www.thewebsite.com that the second content rule matches it 'better' and therefore processes it or would it still be caught by the "/*" content group. I don't want to create more VIPS as I have a real ache getting firewall rules done.
View 9 Replies
ADVERTISEMENT
Oct 2, 2011
Is it possible on the CSS11503 to create a layer 5 content rule that matches a url "/*/_edit".
View 3 Replies
View Related
Mar 27, 2013
I have 2 pair of 11501 switches and 1 pair of 11503 switches on 3 sites(LA, China, Taiwan).Each site has a pair of 1105x switch running as redundancy between them and is a standalone which will not interact with others.Recently a series of interfaces(ports) down happened to every active 1150x switches without any reason and log.Especially today, it happened to active switches at 5:39 AM meanwhile on 3 sites.
View 3 Replies
View Related
Jun 26, 2011
I'm not sure if my terminology is correct when using hairpinning but i was wondering if there is any special config needed when you try to access a content rule VIP from a server that's configured as a member of a source group on the same CSS?
So say i have a content rule with a VIP 20.20.20.20 and i also have two servers 192.168.1.1 and 192.168.1.2 that are part of a source group with VIP of 20.20.20.21. My problem at the moment is if from the servers 192.168.1.x i try to ping the other VIP 20.20.20.20 that's configured on the same CSS then it doesn't work and ping fails. The same happens with HTTP traffic to the 20.20.20.20 VIP.
I would have thought that the NAT of the source group would happen before the routing so the 192.168.1.x IP's would be natted to 20.20.20.21 and then passed over for routing where the CSS would see that the VIP 20.20.20.20 is local and it would send it on it's way.
I thought it might be ACL related but i increased the verbosity of acl logging and couldn't see anything in the logs.The source group works fine on it's own and from the CSS itself i can ping the 20.20.20.20 VIP fine. It just seems that from the source group members i can't ping the VIP.
View 1 Replies
View Related
Aug 26, 2012
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
View 4 Replies
View Related
Aug 1, 2011
Is the XFF [URL] on the Cisco CSS 11503? If not, is it on the roadmap for a future code release?
View 1 Replies
View Related
Jun 9, 2009
i need the MIB object names for monitoring the processor and Memory Utilization of CSS 11503 with software version 7.50 Where can I find it?
View 5 Replies
View Related
Jul 19, 2011
I have a number of web sites that are currently being load balanced by CSS 11503s runninng 8x code. I was recently requested to configure HTTP --> HTTPS redirects on the CSS for every site. In the past, I have only configured the redirects for sites that had a requirement. Now it appears that the server teams want all content encrypted.
1) What impact will this have on the CPU?
2) What impact will this have on Memory utilization?
3) Is there a maximum nubmer on redirects?
4) Are there other things I should be concerned about?
View 3 Replies
View Related
Mar 24, 2013
i have two CSS-11503 in redundant mode running 8.20 code. We had an incident in our network where a layer 2 loop caused some high traffic through the CSS' and had to shutdown some network gear(including the CSS) to clear the problem. When the CSS' were powered back up, the SSL service was suspended, why this would occur? There rest of the config appeared normal. I am the only person on these boxes, the configs were written, and I have never had a reason to suspend the ssl service.
View 1 Replies
View Related
Oct 14, 2012
I know that CSRs cannot be generated with multiple names, but if the SAN is added after the cert is ordered from Geo Trust, Veri sign, etc. can the CSS support using the cert?
View 1 Replies
View Related
Jun 2, 2012
We now have a new requirement . We are replacing existing pair of CSS with ACE 4710 appliances. The problem here is that I can see from the configuration that some SSL certificate installed in CSS .Is it possible to transfer the existing SSL certificate from the 11503 to the ACE? Or, do we need to generate a new key pair and CSR on the ACE? Is there any document available to know the steps for the same.
View 2 Replies
View Related
May 21, 2012
We have several pairs of CSS11501 and 11503 in our network.This issue affects only one pair of CSS11503 in one of our data centres. [code] We use vrrp in one-armed mode for load balancing and they units have performed great for a number of years. We're obviously going to be migrating to ACE ... but not just yet.We have started to experience a problem with replicating the configurations between two CSS11503 in a pair.When running the commit-VipRedundConfig, it starts off happily enough, though slowly.Ending with "working" and the spinning cursor, even after 1 hour the script hasn't completed.We noted on the backup CSS that the APP configuration disappears during the process and I can't remember if this is normal behaviour.
Re-adding the app session configuration seems to interrupt the process, and when checking the configuration on the backup CSS approximately half of it is missing. Everything after the first owner is gone.
1. Configuration is too large, or just large enough to make the commit script take too long for realistic service.
2. Software bug?
3. Combination of both.
4. From now on manually add config to both CSS's and maintain it by process management.
View 5 Replies
View Related
Sep 17, 2012
I only have configured load balancing on apache with a very simple setup. I have to deploy 2 applications on my clients environment that run inside jboss. One of these applications needs session to be sticky to work properly. The other does not.
In apache I can configure is the sticky parameter is true or false, based on the url, like /appA/* is sticky and /appB/* is not sticky. Can I do that in a CSS 11503? My client insists that it is impossible. That the CSS is only ip based.
I copied the configuration below from the manual: owner arrowpoint # content ruleWapSticky
View 14 Replies
View Related
Mar 20, 2012
Am trying to verify performance figures for ACE 4710 as EOL replacement for a CSS 11503 Am sure that the ACE 4710 smokes the CSS but have to complete the due diligence
Pulling figures from data sheets, release notes etc.. I have only come up with the followingIs there any further figures available for the ACE 4710 to fill in the blanks in table?
View 1 Replies
View Related
Apr 27, 2013
I have a single cisco 11503 load balancer.There is a single Banner student information system which is load balanced on it with Virtual ip 10.3.20.101 which is working fine without any issues .I am now trying to add an Oracle ERP application with virtual IP 10.3.20.230 and physical ips 10.3.19.22 and 10.3.19.23 all on port 8003.When I just make the group ERP-Apps-Grp active , the vitual ip address 10.3.20.230 is pingable , but when I make the the content Erp_IAT active it stops pinging. [code]
View 6 Replies
View Related
Sep 11, 2011
what is the "passdetect" command equivalent in CSS 11503 load balancer. software version 8.20.
View 3 Replies
View Related
Sep 26, 2011
what is the OID for See the hit status of the spefic VIP and RIP coming under the VIP .apeart from this CSS box having any module to moniter the hit status or VIP's and RIP's
View 2 Replies
View Related
Nov 29, 2011
I recently "inherited" a CSS 11503 - I've only used ACEs before - and I want to get HTTP keepalives working.To start, I created a test service:
lb-1# show run service sunbird-http-7025-test
!************************** SERVICE **************************
service sunbird-http-7025-test
port 7025
ip address 141.211.229.168
[code].....
View 2 Replies
View Related
Jan 20, 2012
I have a CSS 11503 with a basic content rule for TCP 10000 going to a few backend servers. I was looking into the default timeout values for flows and when testing using telnet the flow didn't terminate as expected?
For example, i have no 'timeout multiplier' specified in the config and when i look at the output of 'show flow-timeout default' it tells me the default 16 seconds timeout is in effect for *. With that in mind, i telnet to the content rule vip on TCP 10000 and on the backend server using wireshark i can see the TCP threeway handshake. With no data passing i'd expect the CSS to terminate this flow after 16 seconds.. yet it takes exactly 128 seconds before wireshark shows the RST and the flow is terminated. 128 being 8 times the default 16 second flow timeout.
If i try to force the connection to close early by specifiying 'flow-timeout-multiplier 2' in the content rule, or even a multiplier of 40, it still waits 128 seconds to close the telnet connection.
View 1 Replies
View Related
Jun 18, 2011
I have already raised this discussion on "LAN, Switching and Routing" group. But I guess this is the right group for my queries. So I am sending my queries in this group again.
We are using CSS 11503 with one 16FE line card. We have connected 3 servers with redundant link. So FE1-2 in Server1, FE 3-4 in Server2 and FE5-6 in Server3. Our system team has configured APA in their servers as they are using HP-Ux.
1) Do we need to do any configuration at line card.
2) Do we need to do ether-channel at loadbalancer end. if yes, can you share me any cisco doc on how to do it.
View 1 Replies
View Related
Sep 11, 2012
We have a pair of CSS 11503 installed in our DC. Stickiness is configured for one of the application since long back and was working pretty fine till last couple of months. Since last two months, we observed that CSS is not distributing sessions the way it suppose to be. Mostly, it forwards the session to same server even though request is coming from different sources. Once we refresh the sessions manually, it starts working fine. We have to do this exercise manually every alternate day.
View 1 Replies
View Related
May 23, 2011
I had meeting with security auditor for a customer, he told me that i need to enable SSL3 on content switch as his scanning found that all network is working on SSL2.I could not understand his view and then when i found the content switch documentation, it is mentioned that SSL3 is default enable on content switch."By default, the SSL version is SSL version 3 and TLS version 1. The SSL module sends a ClientHello that has an SSL version 3 header with the ClientHello message set to TLS version 1." Do i have to do some kind of configuration to enable SSL3 or its enable by default ?
View 3 Replies
View Related
Oct 30, 2011
I am trying to get a sample command output of "show chassis inventory" for:
CSS 11501
CSS 11503
CSS 11506
View 1 Replies
View Related
Jan 23, 2013
I have Cisco 871 router with 12.3. OS version.
1. I'm interested if it's possible to block certain contetn only at certain time ? e.g. We would like to block facebook from 7:00 to 10:00 and from 11:00 to 15:00. I was going through cisco manuals but can't find the right answer to this.
2. Cisco 871 has 4 LAN interfaces and one WAN interface. Currently WAN interface is connected to adsl modem in bridge mode and LAN 0 interface is connected to switch.
I'm interested if I could use remaining 3 LAN interfaces for adsl connections same as I'm using WAN interface. Then I would create vlans that would use LAN interface 0. Each of those VLAN's would use different adsl connection.I would assign different IP to each VLAN's so users would be able to change their gateway and use different ADSL connection.
View 1 Replies
View Related
Oct 24, 2011
As we all know, MS has changed the default workgroup names in different versions of windows. Additionally, you can rename your workgroup anything you like. I have XP, Vista, and Win7 computers, a television, BluRay player, a Wii, two printers, and a NAS with two USB drives attached. All of these -except the Win7- are wired to one of two switches. I have wireless: iPad, the Win7 notebook, Nintendo DSs. I have friend, and non-friend machines (computers, tablets, and phones) that come and go that are wired or wireless. The 3 windows computers all have the same workgroup name. All of my other units do not use workgroup names. I have a router, and two unmanaged switches, and have, on occasion, a second router. The main router, which has wired, and dual band wireless (each with two named wireless networks) nets, sees everything, by name and/or MAC address. Win7 is blind, deaf, and dumb.: it shows its own workgroup name, but no other workgroup name(s) , and, consequently, no unit on these other workgroups. It will show some wired units not in a workgroups - the television, and the printers (not the Wii or NAS). It will not show the wired XP computer! No wireless units either in workgroups or not in workgroups appear. Additionally, Win7 only shows units on its wireless network, not on the other three. The wired units it does show are not on any of the wireless networks, though it lists them on its wireless network.I have left the Homegroup, and terminated the Homegroup services. I have allowed discovery, and unlimited sharing of everything on every computer on the router, and yet the Win7 unit does not share or see well at all.Why?
View 2 Replies
View Related
Feb 16, 2012
I'm trying to design a CSS configuration that allows servers in the same vlan to be the source and destination of load-balanced traffic. My thought is to add two new vlans, one for the VIPs and one for the servers, then NAT the source IPs going from the LB to the servers.
Is this the right way to do it?I've never NATted using CSSs, so I wanted to verify what I'm thinking.Our current config trunks the vlans -
interface 1/1
trunk
vlan 1
default-vlan
vlan 555
[code]....
View 3 Replies
View Related
Jan 24, 2011
I have 2 routers ( Cisco 3845's) both running identical IOS's. Each router has identical 5 networks on it with one network each being different.I have HSRP set up on the identical 5 networks.Your standard Fail over senario.ON one of the routers one network is not seeing the other router in the same network, Will not Ping or traceroute.And HSRP stopped working ( both were thinking they were active. which of course brought the network to a halt. Non of the interfaces has any ACL on them, They are plugged into a Brand new Cisco 3560v2 switch. I have switches out the cables to eliminate that as an issues.
View 1 Replies
View Related
Jan 14, 2013
I have multiple campuses and a Central Admin...I've created Groups for all, except I need a few devices within Central to be available to the Campus Admins... (ie..a Cisco WCS System) How do I allow a device to be put into multiple NDG groups?
View 1 Replies
View Related
Feb 14, 2013
We are in a warehouse type setting and have data centers on each side of warehouse with 5508 WLC's in each data center. Each side is on its own subnet with routing in between and a different set of SSID's for each set of WLC’s. Are goal is to have the ability to failover in the event that if one data center goes down AP’s will move to the controllers in the other DC and the clients will still be able to operate.
Our thought was to implement mobility groups between the controllers. While I saw documentation on setting this up when the controllers are on the same vlan, I didnt see any setup config when controllers are in different vlans. So I am wondering if mobility groups are even an option for what we want to accomplish. For the most part clients stay on their respected sides of the warehouse and so we are not necessarily needing roaming for clients between controllers in DC1 and DC2. But that does raise another question in that we do have a planned voice wlan that we would like to have the ability to roam between each side of the warehouse. But we have seen ip issues with this. In the past we have had both SSID's setup on each side and ran to issues with clients not renewing their IP address when moving to the controllers on the different subnets.
Can we setup mobility groups between controllers on different vlans/subnets? For failover purposes will mobility groups assist in our setup with 2 DC’s and different subnets/vlans? If the answer is yes we can setup mobility groups between different subnets, is there a way to setup the SSID's on all controllers and have the ability for clients to roam and renew their IP’s when moving to a different controller on a different subnet?
View 3 Replies
View Related
Feb 24, 2013
i have a question about multiple TACACS Groups. I want to archive the following:
A Cisco 888 is managed by me and a Provider Support Team. Since we both want to access our own TACACS Server, i want to create two TACACS Groups. Is it possible to me, to bind a Tacacs Group to one Interface, and the second TACACS Group to another ? Means that our stuff is connecting to the LAN Interface FastEthernet0 that is applied to the SVI in V LAN 1.
The service technicians from the Provider are connecting to the external Interface or through a possible Lo. (another IP). I do not want to mix our 2 TACACS+ Server and theirs together in one Group. So have anybody tried this before ?
View 8 Replies
View Related
Feb 15, 2011
We have multiple RA VPN groups on a 3845 router.RADIUS authentication is currently happening between the 3845 and a single Windows 2008 server. We have a specific windows group that AD users are members of, and they are allowed to connect via VPN.
I'm creating a new RA VPN Group, which should only allow different AD users. Is it possible to create another RADIUS association to the same server, or do I need to authenticate against a different Windows server?
View 1 Replies
View Related
May 4, 2011
I'm working with a 1113 ACS device running the 4.2.0.124 software. I'm trying to get multiple network device groups to use an existing Remote Agent set up for authentication against our Windows domain. For instance, we want our infrastructure switches to authenticate agains the local Active Directory and our WLC to authenticate users agains the same Active Directory. When I try and set both network device groups to use the same remote agent, it fails and reports either the host name is already in use or the IP address overlaps with an existing remote agent.
The question is:
Can I have multiple network device groups use the same remote agent? Or do I have to install the remote agent software on separate Windows servers in order to have different types of devices authenticate against the Windows AD?
View 1 Replies
View Related
Dec 12, 2011
I created some User Defined Groups in LMS 4.1, now I want to apply certain fault notification groups to Event Sets.
Unfortunately the Groups I configured are not in the Group Selector of the Fault Notification Group: Admin > Network > Notification and Action Settings > Fault Notification Group
View 3 Replies
View Related
