I have a number of web sites that are currently being load balanced by CSS 11503s runninng 8x code. I was recently requested to configure HTTP --> HTTPS redirects on the CSS for every site. In the past, I have only configured the redirects for sites that had a requirement. Now it appears that the server teams want all content encrypted.
1) What impact will this have on the CPU? 2) What impact will this have on Memory utilization? 3) Is there a maximum nubmer on redirects? 4) Are there other things I should be concerned about?
i have two CSS-11503 in redundant mode running 8.20 code. We had an incident in our network where a layer 2 loop caused some high traffic through the CSS' and had to shutdown some network gear(including the CSS) to clear the problem. When the CSS' were powered back up, the SSL service was suspended, why this would occur? There rest of the config appeared normal. I am the only person on these boxes, the configs were written, and I have never had a reason to suspend the ssl service.
We now have a new requirement . We are replacing existing pair of CSS with ACE 4710 appliances. The problem here is that I can see from the configuration that some SSL certificate installed in CSS .Is it possible to transfer the existing SSL certificate from the 11503 to the ACE? Or, do we need to generate a new key pair and CSR on the ACE? Is there any document available to know the steps for the same.
We have several pairs of CSS11501 and 11503 in our network.This issue affects only one pair of CSS11503 in one of our data centres. [code] We use vrrp in one-armed mode for load balancing and they units have performed great for a number of years. We're obviously going to be migrating to ACE ... but not just yet.We have started to experience a problem with replicating the configurations between two CSS11503 in a pair.When running the commit-VipRedundConfig, it starts off happily enough, though slowly.Ending with "working" and the spinning cursor, even after 1 hour the script hasn't completed.We noted on the backup CSS that the APP configuration disappears during the process and I can't remember if this is normal behaviour.
Re-adding the app session configuration seems to interrupt the process, and when checking the configuration on the backup CSS approximately half of it is missing. Everything after the first owner is gone.
1. Configuration is too large, or just large enough to make the commit script take too long for realistic service. 2. Software bug? 3. Combination of both. 4. From now on manually add config to both CSS's and maintain it by process management.
I only have configured load balancing on apache with a very simple setup. I have to deploy 2 applications on my clients environment that run inside jboss. One of these applications needs session to be sticky to work properly. The other does not.
In apache I can configure is the sticky parameter is true or false, based on the url, like /appA/* is sticky and /appB/* is not sticky. Can I do that in a CSS 11503? My client insists that it is impossible. That the CSS is only ip based.
I copied the configuration below from the manual: owner arrowpoint # content ruleWapSticky
I have a single cisco 11503 load balancer.There is a single Banner student information system which is load balanced on it with Virtual ip 10.3.20.101 which is working fine without any issues .I am now trying to add an Oracle ERP application with virtual IP 10.3.20.230 and physical ips 10.3.19.22 and 10.3.19.23 all on port 8003.When I just make the group ERP-Apps-Grp active , the vitual ip address 10.3.20.230 is pingable , but when I make the the content Erp_IAT active it stops pinging. [code]
content My_Group add service blade1 add service blade2 add service blade3 vip address 188.8.131.52 advanced-balance arrowpoint-cookie
So I have 3 blades which are proxy servers and user go first to an MS ISA server then the VIP of the CSS and then the rules processes them give them a blade and chuck them out onto the Internet.
I want to leave the above rule, but remove one blade create an additional content group with that blade and have it process requests for a particular site so, I would create the following
content My_Group2 add service blade3 vip address 184.108.40.206 advanced-balance arrowpoint-cookie
So my question is can I do that having the same VIP's etc so if a request comes in and it matches www.thewebsite.com that the second content rule matches it 'better' and therefore processes it or would it still be caught by the "/*" content group. I don't want to create more VIPS as I have a real ache getting firewall rules done.
I'm not sure if my terminology is correct when using hairpinning but i was wondering if there is any special config needed when you try to access a content rule VIP from a server that's configured as a member of a source group on the same CSS?
So say i have a content rule with a VIP 220.127.116.11 and i also have two servers 192.168.1.1 and 192.168.1.2 that are part of a source group with VIP of 18.104.22.168. My problem at the moment is if from the servers 192.168.1.x i try to ping the other VIP 22.214.171.124 that's configured on the same CSS then it doesn't work and ping fails. The same happens with HTTP traffic to the 126.96.36.199 VIP.
I would have thought that the NAT of the source group would happen before the routing so the 192.168.1.x IP's would be natted to 188.8.131.52 and then passed over for routing where the CSS would see that the VIP 184.108.40.206 is local and it would send it on it's way.
I thought it might be ACL related but i increased the verbosity of acl logging and couldn't see anything in the logs.The source group works fine on it's own and from the CSS itself i can ping the 220.127.116.11 VIP fine. It just seems that from the source group members i can't ping the VIP.
I have a CSS 11503 with a basic content rule for TCP 10000 going to a few backend servers. I was looking into the default timeout values for flows and when testing using telnet the flow didn't terminate as expected?
For example, i have no 'timeout multiplier' specified in the config and when i look at the output of 'show flow-timeout default' it tells me the default 16 seconds timeout is in effect for *. With that in mind, i telnet to the content rule vip on TCP 10000 and on the backend server using wireshark i can see the TCP threeway handshake. With no data passing i'd expect the CSS to terminate this flow after 16 seconds.. yet it takes exactly 128 seconds before wireshark shows the RST and the flow is terminated. 128 being 8 times the default 16 second flow timeout.
If i try to force the connection to close early by specifiying 'flow-timeout-multiplier 2' in the content rule, or even a multiplier of 40, it still waits 128 seconds to close the telnet connection.
I have already raised this discussion on "LAN, Switching and Routing" group. But I guess this is the right group for my queries. So I am sending my queries in this group again.
We are using CSS 11503 with one 16FE line card. We have connected 3 servers with redundant link. So FE1-2 in Server1, FE 3-4 in Server2 and FE5-6 in Server3. Our system team has configured APA in their servers as they are using HP-Ux.
1) Do we need to do any configuration at line card.
2) Do we need to do ether-channel at loadbalancer end. if yes, can you share me any cisco doc on how to do it.
We have a pair of CSS 11503 installed in our DC. Stickiness is configured for one of the application since long back and was working pretty fine till last couple of months. Since last two months, we observed that CSS is not distributing sessions the way it suppose to be. Mostly, it forwards the session to same server even though request is coming from different sources. Once we refresh the sessions manually, it starts working fine. We have to do this exercise manually every alternate day.
I have 2 pair of 11501 switches and 1 pair of 11503 switches on 3 sites(LA, China, Taiwan).Each site has a pair of 1105x switch running as redundancy between them and is a standalone which will not interact with others.Recently a series of interfaces(ports) down happened to every active 1150x switches without any reason and log.Especially today, it happened to active switches at 5:39 AM meanwhile on 3 sites.
I'm trying to design a CSS configuration that allows servers in the same vlan to be the source and destination of load-balanced traffic. My thought is to add two new vlans, one for the VIPs and one for the servers, then NAT the source IPs going from the LB to the servers.
Is this the right way to do it?I've never NATted using CSSs, so I wanted to verify what I'm thinking.Our current config trunks the vlans -
Report run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.
I am taking an introduction class to CCNA and we are focusing on the Application Layer,and I'm having some difficulty in understanding what is an Application Layer Service. Is the Application Layer Service the same as Application Layer Software?
Is it possible to upgrade ACE 4710 from A3 to A4? What does this actualy means by A3, A4 & A5.
I want to upgrade ACE from A3 to A4 becase I want to enable switch-mode on ACE. Current S/W version is A3 2.0 which is not supporting this command. While reffering the command refernce guide saw that this command is supported in A2 & A4 version from 2.0 itself but for A3 in 2.7 (which is the latest) also this is not supporting this feature.
We've got an application that broke after upgrading our ACEs from A5(2.1) to A5(2.2); the problem lies in how the ACE handles URLs with embedded backslash characters in them - e.g.: URL
Prior to the upgrade the ACE would forward these to the back-end servers; after the upgrade the ACE resets the client connection. (We're doing SSL offload on the ACE; the back-end connection is HTTP over port 80, only the client-side traffic is over SSL.)
Some browsers will convert these to percent-encoded form - i.e. URL
and things work for these; but other browsers won't do this. So I'd like to set up a rewrite rule in the ACE that will replace any (or at least the first) '' with the string '%5C'. Just how to do this isn't clear from the command ref, and the config guide is a tad shy on similar examples.
As per CISCO QoS document URL, IOS from 12.2(13)T support drop command in policy map. But our CISCO ASR 1013 having IOS of Version 15.2(1)S1 doesn't have drop syntax.How can we drop specific application using QoS in ASR 1013 of IOS version 15.2 and higher?,Can I allow few users for a particular application (like P2P) and drop other users based on users source IP?
I want to deploy a high availability solution for web servers in two data centers. In the primary data center I have deployed a group of web server and I want two deploy additional servers in a secondary data center for disaster recovery and high availability. Reviewing the documentation, looks like the GSS4492 is the solution for my company needs but I am not sure if I have to implement just the GSS or if I need a ACE4700 integrated with the GSS?.