Cisco Application :: CSS 11503 SSL Service Suspended
Mar 24, 2013
i have two CSS-11503 in redundant mode running 8.20 code. We had an incident in our network where a layer 2 loop caused some high traffic through the CSS' and had to shutdown some network gear(including the CSS) to clear the problem. When the CSS' were powered back up, the SSL service was suspended, why this would occur? There rest of the config appeared normal. I am the only person on these boxes, the configs were written, and I have never had a reason to suspend the ssl service.
View 1 Replies
ADVERTISEMENT
Aug 1, 2011
Is the XFF [URL] on the Cisco CSS 11503? If not, is it on the roadmap for a future code release?
View 1 Replies
View Related
Jun 9, 2009
i need the MIB object names for monitoring the processor and Memory Utilization of CSS 11503 with software version 7.50 Where can I find it?
View 5 Replies
View Related
Jul 19, 2011
I have a number of web sites that are currently being load balanced by CSS 11503s runninng 8x code. I was recently requested to configure HTTP --> HTTPS redirects on the CSS for every site. In the past, I have only configured the redirects for sites that had a requirement. Now it appears that the server teams want all content encrypted.
1) What impact will this have on the CPU?
2) What impact will this have on Memory utilization?
3) Is there a maximum nubmer on redirects?
4) Are there other things I should be concerned about?
View 3 Replies
View Related
Oct 14, 2012
I know that CSRs cannot be generated with multiple names, but if the SAN is added after the cert is ordered from Geo Trust, Veri sign, etc. can the CSS support using the cert?
View 1 Replies
View Related
Jun 2, 2012
We now have a new requirement . We are replacing existing pair of CSS with ACE 4710 appliances. The problem here is that I can see from the configuration that some SSL certificate installed in CSS .Is it possible to transfer the existing SSL certificate from the 11503 to the ACE? Or, do we need to generate a new key pair and CSR on the ACE? Is there any document available to know the steps for the same.
View 2 Replies
View Related
May 21, 2012
We have several pairs of CSS11501 and 11503 in our network.This issue affects only one pair of CSS11503 in one of our data centres. [code] We use vrrp in one-armed mode for load balancing and they units have performed great for a number of years. We're obviously going to be migrating to ACE ... but not just yet.We have started to experience a problem with replicating the configurations between two CSS11503 in a pair.When running the commit-VipRedundConfig, it starts off happily enough, though slowly.Ending with "working" and the spinning cursor, even after 1 hour the script hasn't completed.We noted on the backup CSS that the APP configuration disappears during the process and I can't remember if this is normal behaviour.
Re-adding the app session configuration seems to interrupt the process, and when checking the configuration on the backup CSS approximately half of it is missing. Everything after the first owner is gone.
1. Configuration is too large, or just large enough to make the commit script take too long for realistic service.
2. Software bug?
3. Combination of both.
4. From now on manually add config to both CSS's and maintain it by process management.
View 5 Replies
View Related
Sep 17, 2012
I only have configured load balancing on apache with a very simple setup. I have to deploy 2 applications on my clients environment that run inside jboss. One of these applications needs session to be sticky to work properly. The other does not.
In apache I can configure is the sticky parameter is true or false, based on the url, like /appA/* is sticky and /appB/* is not sticky. Can I do that in a CSS 11503? My client insists that it is impossible. That the CSS is only ip based.
I copied the configuration below from the manual: owner arrowpoint # content ruleWapSticky
View 14 Replies
View Related
Mar 20, 2012
Am trying to verify performance figures for ACE 4710 as EOL replacement for a CSS 11503 Am sure that the ACE 4710 smokes the CSS but have to complete the due diligence
Pulling figures from data sheets, release notes etc.. I have only come up with the followingIs there any further figures available for the ACE 4710 to fill in the blanks in table?
View 1 Replies
View Related
Apr 27, 2013
I have a single cisco 11503 load balancer.There is a single Banner student information system which is load balanced on it with Virtual ip 10.3.20.101 which is working fine without any issues .I am now trying to add an Oracle ERP application with virtual IP 10.3.20.230 and physical ips 10.3.19.22 and 10.3.19.23 all on port 8003.When I just make the group ERP-Apps-Grp active , the vitual ip address 10.3.20.230 is pingable , but when I make the the content Erp_IAT active it stops pinging. [code]
View 6 Replies
View Related
Sep 11, 2011
what is the "passdetect" command equivalent in CSS 11503 load balancer. software version 8.20.
View 3 Replies
View Related
Oct 4, 2011
I currently have a content group as follows;
content My_Group
add service blade1
add service blade2
add service blade3
vip address 1.2.3.4
advanced-balance arrowpoint-cookie
[code]...
So I have 3 blades which are proxy servers and user go first to an MS ISA server then the VIP of the CSS and then the rules processes them give them a blade and chuck them out onto the Internet.
I want to leave the above rule, but remove one blade create an additional content group with that blade and have it process requests for a particular site so, I would create the following
content My_Group2
add service blade3
vip address 1.2.3.4
advanced-balance arrowpoint-cookie
[code]...
So my question is can I do that having the same VIP's etc so if a request comes in and it matches www.thewebsite.com that the second content rule matches it 'better' and therefore processes it or would it still be caught by the "/*" content group. I don't want to create more VIPS as I have a real ache getting firewall rules done.
View 9 Replies
View Related
Jun 26, 2011
I'm not sure if my terminology is correct when using hairpinning but i was wondering if there is any special config needed when you try to access a content rule VIP from a server that's configured as a member of a source group on the same CSS?
So say i have a content rule with a VIP 20.20.20.20 and i also have two servers 192.168.1.1 and 192.168.1.2 that are part of a source group with VIP of 20.20.20.21. My problem at the moment is if from the servers 192.168.1.x i try to ping the other VIP 20.20.20.20 that's configured on the same CSS then it doesn't work and ping fails. The same happens with HTTP traffic to the 20.20.20.20 VIP.
I would have thought that the NAT of the source group would happen before the routing so the 192.168.1.x IP's would be natted to 20.20.20.21 and then passed over for routing where the CSS would see that the VIP 20.20.20.20 is local and it would send it on it's way.
I thought it might be ACL related but i increased the verbosity of acl logging and couldn't see anything in the logs.The source group works fine on it's own and from the CSS itself i can ping the 20.20.20.20 VIP fine. It just seems that from the source group members i can't ping the VIP.
View 1 Replies
View Related
Sep 26, 2011
what is the OID for See the hit status of the spefic VIP and RIP coming under the VIP .apeart from this CSS box having any module to moniter the hit status or VIP's and RIP's
View 2 Replies
View Related
Feb 28, 2012
We have a situation where services are stopped on the real servers. The probes fail and we confirm the services are not running on the server. We cannot access the ports from the ACE directly. We can still however acces the VIP on the TCP port (L4 VIP class-map). So we can still telnet to the VIP on the port from thr Client side of the network.This is on ACE 20 Modules deployed in Routed mode. The version of software is A2(3.3).
Tried removing multi-match and loadbalance policies as well as class-map and re-applying then re-appyling the service policy to interface. Same behavior,This is a problem at another level as some services are being monitored by GSS via TCP keep-Alive and this obviuosly causes a problem as the service then never goes off-line.
View 10 Replies
View Related
Nov 29, 2011
I recently "inherited" a CSS 11503 - I've only used ACEs before - and I want to get HTTP keepalives working.To start, I created a test service:
lb-1# show run service sunbird-http-7025-test
!************************** SERVICE **************************
service sunbird-http-7025-test
port 7025
ip address 141.211.229.168
[code].....
View 2 Replies
View Related
Jan 20, 2012
I have a CSS 11503 with a basic content rule for TCP 10000 going to a few backend servers. I was looking into the default timeout values for flows and when testing using telnet the flow didn't terminate as expected?
For example, i have no 'timeout multiplier' specified in the config and when i look at the output of 'show flow-timeout default' it tells me the default 16 seconds timeout is in effect for *. With that in mind, i telnet to the content rule vip on TCP 10000 and on the backend server using wireshark i can see the TCP threeway handshake. With no data passing i'd expect the CSS to terminate this flow after 16 seconds.. yet it takes exactly 128 seconds before wireshark shows the RST and the flow is terminated. 128 being 8 times the default 16 second flow timeout.
If i try to force the connection to close early by specifiying 'flow-timeout-multiplier 2' in the content rule, or even a multiplier of 40, it still waits 128 seconds to close the telnet connection.
View 1 Replies
View Related
Oct 2, 2011
Is it possible on the CSS11503 to create a layer 5 content rule that matches a url "/*/_edit".
View 3 Replies
View Related
Jun 18, 2011
I have already raised this discussion on "LAN, Switching and Routing" group. But I guess this is the right group for my queries. So I am sending my queries in this group again.
We are using CSS 11503 with one 16FE line card. We have connected 3 servers with redundant link. So FE1-2 in Server1, FE 3-4 in Server2 and FE5-6 in Server3. Our system team has configured APA in their servers as they are using HP-Ux.
1) Do we need to do any configuration at line card.
2) Do we need to do ether-channel at loadbalancer end. if yes, can you share me any cisco doc on how to do it.
View 1 Replies
View Related
Sep 11, 2012
We have a pair of CSS 11503 installed in our DC. Stickiness is configured for one of the application since long back and was working pretty fine till last couple of months. Since last two months, we observed that CSS is not distributing sessions the way it suppose to be. Mostly, it forwards the session to same server even though request is coming from different sources. Once we refresh the sessions manually, it starts working fine. We have to do this exercise manually every alternate day.
View 1 Replies
View Related
Mar 27, 2013
I have 2 pair of 11501 switches and 1 pair of 11503 switches on 3 sites(LA, China, Taiwan).Each site has a pair of 1105x switch running as redundancy between them and is a standalone which will not interact with others.Recently a series of interfaces(ports) down happened to every active 1150x switches without any reason and log.Especially today, it happened to active switches at 5:39 AM meanwhile on 3 sites.
View 3 Replies
View Related
Oct 30, 2011
I am trying to get a sample command output of "show chassis inventory" for:
CSS 11501
CSS 11503
CSS 11506
View 1 Replies
View Related
Feb 16, 2012
I'm trying to design a CSS configuration that allows servers in the same vlan to be the source and destination of load-balanced traffic. My thought is to add two new vlans, one for the VIPs and one for the servers, then NAT the source IPs going from the LB to the servers.
Is this the right way to do it?I've never NATted using CSSs, so I wanted to verify what I'm thinking.Our current config trunks the vlans -
interface 1/1
trunk
vlan 1
default-vlan
vlan 555
[code]....
View 3 Replies
View Related
Apr 3, 2012
I am taking an introduction class to CCNA and we are focusing on the Application Layer,and I'm having some difficulty in understanding what is an Application Layer Service. Is the Application Layer Service the same as Application Layer Software?
View 3 Replies
View Related
Oct 14, 2012
some misconfiguration (?) may be the reason for an undesired behaviour we are experiencing with our Cisco CSS 11501s. Balancing mechanisms work fine, however if a service transitions to the "down" state, the corresponding flows remain "alive" leading to a temporary outage of our service. Subsequent client requests are still being sent to the "down" frontend which is unresponsive.
View 4 Replies
View Related
Nov 28, 2012
I have an ACE4710 with a few basic farms running and it works great however I now need to implement an SSL proxy service for the first time. The requirement is that clients who are already using FQDN's need to be sent to diffent real server IP addresses as each client will have their own VM. All the clients will use the same global IP address with different A records.
View 1 Replies
View Related
Dec 27, 2011
I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?
View 2 Replies
View Related
Sep 1, 2010
Does ACE service module support SHA2(256) certificates? I see that private key generation defaults to SHA1 and does not provide any option, also the cipher suites in SSL parameters map do not show SHA2 options. Can it handle SHA2 in any software release? I am currently running A2(2.3) build 3.00
View 6 Replies
View Related
Dec 2, 2012
My ACE module ACE30-MOD-K9 crashed today, and at the show ver output i see "last boot reason: Service "cfgmgr" ".the curent version we running is Version A5(1.2) [build 3.0(0)A5(1.2).
After doing some research i found known bug that supposed to be fixed in this version: CSCtu36146
CSCtu36146—The ACE becomes unresponsive due to a configuration manager (Cfgmgr) process failure with the last boot reason: Service "cfgmgr."
View 2 Replies
View Related
Dec 20, 2011
i need to be able to find out what application/service is sending out net bios broadcasts on a network segment the requests are for machines that no longer are on the network but something is trying to obtain there ip address as they are not in dns any more i am assuming this is why they are resorting to netbios broadcasts i need to some how isolate what application or service is trying to find out.
View 7 Replies
View Related
Jan 25, 2012
I just bought 4 units of Cisco ESW-520 24Ports switches. I did some testing and found out for PORTS 1 and 12 is in "Suspended" mode and thus not able to use.This not happened to 1 but all 4 switches. Why is this so? How to disable the ports from going into "suspended" mode automatically ? I wouldn't want the ports to be in "Suspension" mode when it goes live and thus block the desktops from having internet access.
View 2 Replies
View Related
Nov 9, 2011
if a Cisco router or switch can handle wccp redirection enabled for both waas and some other web content filtering appliance using a different service group?
seems like the priority value would come into play determining which service group gets handled first?
we currently do WCCP for WaaS on our 3945s.
I am going to advocate to my customer that we separate this out for CPU load issues, config complexity issues, IOS issues, etc... but the question is going to come up - "can we do WCCP for different applications on our Catalyst 3750 core switch, or our 3945 WAN routers?"
View 2 Replies
View Related
Dec 23, 2012
I describe an issue when i need to performe an L2 or L3 Etherchannel from a Catalyst 4948 IOS Enterprise and 2 xCatalyst 6506E bandled with VSS.
From the VSS Side when i plug cables i see on the physicals and Etherchannel that Physical and protocole layer are up. On the 4948 side, I see that physical layer is up and protocol and Etherchannel interfaces are down.
On the Etherchannel port summary i see that the port state is supended.
On the first attempt, i have test with a L3 etherchannel on both side using no switchport with two IP addresses one at each side on etherchannel interfaces.
The etherchannel are bundled with LACP mode active and on the second attempt with PAGP mode ON.
The same configured on VSS 6506E work fine with Catalyst 3560E.
View 3 Replies
View Related
