Cisco Application :: CSS 11503 Ether-channel Configuration For Redundant Server Link
Jun 18, 2011
I have already raised this discussion on "LAN, Switching and Routing" group. But I guess this is the right group for my queries. So I am sending my queries in this group again.
We are using CSS 11503 with one 16FE line card. We have connected 3 servers with redundant link. So FE1-2 in Server1, FE 3-4 in Server2 and FE5-6 in Server3. Our system team has configured APA in their servers as they are using HP-Ux.
1) Do we need to do any configuration at line card.
2) Do we need to do ether-channel at loadbalancer end. if yes, can you share me any cisco doc on how to do it.
View 1 Replies
ADVERTISEMENT
Dec 1, 2011
I came across a Catalyst 6509 switch configuration and have noticed some strange thing on the ether channel configuration side, it appears that it have interface port-channel 2 and port-channel 2A, what was that mean? its the ether channel not forming and joined together?
What wrong with the below configuration that cause it to automatic created another port-channel (2A) interface in this case?
[code]...
View 3 Replies
View Related
Feb 16, 2012
I'm trying to design a CSS configuration that allows servers in the same vlan to be the source and destination of load-balanced traffic. My thought is to add two new vlans, one for the VIPs and one for the servers, then NAT the source IPs going from the LB to the servers.
Is this the right way to do it?I've never NATted using CSSs, so I wanted to verify what I'm thinking.Our current config trunks the vlans -
interface 1/1
trunk
vlan 1
default-vlan
vlan 555
[code]....
View 3 Replies
View Related
Sep 17, 2012
I only have configured load balancing on apache with a very simple setup. I have to deploy 2 applications on my clients environment that run inside jboss. One of these applications needs session to be sticky to work properly. The other does not.
In apache I can configure is the sticky parameter is true or false, based on the url, like /appA/* is sticky and /appB/* is not sticky. Can I do that in a CSS 11503? My client insists that it is impossible. That the CSS is only ip based.
I copied the configuration below from the manual: owner arrowpoint # content ruleWapSticky
View 14 Replies
View Related
Nov 29, 2011
I recently "inherited" a CSS 11503 - I've only used ACEs before - and I want to get HTTP keepalives working.To start, I created a test service:
lb-1# show run service sunbird-http-7025-test
!************************** SERVICE **************************
service sunbird-http-7025-test
port 7025
ip address 141.211.229.168
[code].....
View 2 Replies
View Related
Mar 19, 2013
We are running ACE 20 modules in highly available active / standby (all active contexts on one module) mode. Currently they are on A2 (2.4) version. We are going to upgrade them to A2 (3.6a). The question is that how ling can we run them in two different SW levels? In otherwords can we have few days between upgrading both modules?
View 1 Replies
View Related
Mar 27, 2013
I have 2 pair of 11501 switches and 1 pair of 11503 switches on 3 sites(LA, China, Taiwan).Each site has a pair of 1105x switch running as redundancy between them and is a standalone which will not interact with others.Recently a series of interfaces(ports) down happened to every active 1150x switches without any reason and log.Especially today, it happened to active switches at 5:39 AM meanwhile on 3 sites.
View 3 Replies
View Related
Sep 23, 2012
I was configured ether channel between two cisco 2960s series switches. It is working properly. I was replaced two cables in etherchannel. Now one link working remaining link is down(both cables are working cables only). Below are ether channel details.
View 9 Replies
View Related
Jan 10, 2012
running ether-channel mode on. I have a 3120G Blade Switch (stacked). The blade switch connects to the blade servers (internal). Gi1 /0/1 connects to eth0 and gi2/0/1 connects to eth1 on the blade server. [code]
The issue is when is shutdown eth0 on the server, the corresponding interface on the switch (gi1/0/1) does not go down, show up and running.
View 3 Replies
View Related
Dec 25, 2012
I have trunk etherchannel ports 47,48 which both have Vlans allowed on trunk 70,71. Everything works pretty fine. Now I am trying to add a new VLAN 72 to these ports.
conf t
interface FastEthernet0/47
switchport trunk allowed vlan add 72
exit
exit
So far so good. But when making the same command for port FastEthernet0/48 my switch stuck.
View 8 Replies
View Related
May 3, 2012
I know there are some line cards on the 6500 that do not play well with each other when trying to setup an etherchannel using two different line cards on the same chassis. I always thought it was line cards of different type, i.e. 6400 with a 6700 but these two line cards are exactly the same model with the same code level.
1) Are the error messages below from this incompatibility between line cards and etherchannel creation?
2) How to fix if the answer to #1 is yes?
3) What line cards work with which for etherchannel creation?
View 11 Replies
View Related
Jan 17, 2013
Is it possible to configure a cross stack etherchannel between 2 SG500 (in stack) and 1 SG200/SG300?
View 13 Replies
View Related
May 19, 2013
We were going to create a 2 port, layer 3 etherchannel between a 1002 router and a 3750X layer 3 core switch. We wanted to create bunled link between them but, now we are going to be putting a Riverbed device between the router and core switch. Because of this, would it be best to abandon the idea of creating a layer 3 etherchannel and just have 2 links from the router and core switch and have traffic load balance between the 2 links?The Riverbed will have 2 connections into it from the Core switch and 2 connections into it from the 1002 router. I was hoping to keep the layer 3 etherchannel but, do you think it would be best to create 2, /29 nets and have the router/Riverbed and Core Switch/Riverbed load balance.
View 5 Replies
View Related
Feb 22, 2012
i want to realize a 20gb ring stp with 6 3750x stacked by 2. I want to install 2 3750x stacked configured in hsrp mode with other 2 3750 stacked. These 2 different stack are interconnected by a cross-stack ether channel 20Gb fiber. On the other side of the room i want to create a new stack with 2 3750x with cross-stack ether channel 20gb connected with the previous 2 stacks. So, in total 3 different cross-stack ether channel 20Gb stacks interconnected creating a ring stp of 20 Gb.
View 4 Replies
View Related
Mar 15, 2011
I have an 891W that I initially configured using CCP Express (2.5). So it has a WAN IP set, and through CCP Express I had enabled via the checkboxes the various default settings for security. This includes zone-based firewall. I then added a number of NAT entries in the setup wizard.
What never occured to me at the time was that I should have added entries that allow for remote access. So it seems I've locked myself out of accessing the router via the WAN interface even though I know it's IP. I'm sure it's just a matter of adding port exceptions for SSH and/or whatever port(s) CCP uses.
So I"m wondering what the proces woudl be. In the IOS while showing the running config., I see pages and pages of class-map stuff which at present I don't know enough about to risk editing anything directly. But maybe I don't have to? What would be the best way to, for example, enable SSH access through the firewall? I already have transport input ssh set on the interface itself so I believe it's ready to allow the connection, just that I can't get to it via WAN int. so I assume it's the firewall.
View 3 Replies
View Related
Aug 6, 2012
I try to connect a cisco blade switch 3020 to Nexus 2232 with etherchannel, but when I connect the second link a obtain flapping on vlans. [code] why the vlans are flapping ? it's something wrong on the config ? [code]
View 7 Replies
View Related
Oct 8, 2012
I have 4 cisco 2960 switches to which many users are connected. No vlans are the only default vlan 1 is there. Now I want to make ether channel on switch 1 whcih has 24 fast etherenet ports. Can I make port 1- 8 as one ether channel which are connected to users or i can only make ethere channel of ports that are connectd to other switchs. If I can, how the other switchs will comnicate with the switch ports bundalled in the ether channel in switch 1.
View 6 Replies
View Related
Mar 9, 2012
I have two switch SG300-10 that need to be interconnect togheter with a simple redundant "cable fail safe" configuration.My idea is use the two uplink copper port of the first switch, connected to the two uplink copper port of the second switch.
How to create a working setup configuration? The first setup that i need, is with only one VLAN1 for all ports,
The second setup is with the VLAN1 assigned to the ports 1-2-3-4 of all the two switch, (linked togheter by uplink ports)
and the VLAN2 assigned to the ports 5-6-7-8 always linked togheter with the same uplink ports.
Is possible use the two uplink port at the same time, as cable fail safe? or use a uplink port 1 for the first group and the second uplink port for second group?
I need to use this configuration for audio cobranet transport, and i need to test the correct configuration for the primary and secondary audio stream, if can work togheter on the same VLAN or i need to separate the two stream, from start to the end.
View 1 Replies
View Related
Aug 1, 2011
Is the XFF [URL] on the Cisco CSS 11503? If not, is it on the roadmap for a future code release?
View 1 Replies
View Related
Jun 9, 2009
i need the MIB object names for monitoring the processor and Memory Utilization of CSS 11503 with software version 7.50 Where can I find it?
View 5 Replies
View Related
Feb 24, 2013
I have a two fiber connection from our Central Office(6513) to Remote office (6509). I have a requirement that on the remote office if one of the fiber goes down, the second fiber should work as a failover. I am planning to use SUP720-3B SFP to connect to the CO.
Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G5/2? or Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G6/2? I am running EIGRP between sites. Any sample config.
sup-bootflash:s72033-pk9sv-mz.122-18.SXD7b.bin"
View 4 Replies
View Related
Sep 24, 2012
A site that i am responsible for has the following equipment installed:
2 x 3750G Switches configured as a stack using Stackwise - Collapsed Core/Distribution Layer
5 x 2960G Switches as Access Layer switches
WAN connections into the Core/Distribution Layer are all Gigabit Ethernet over Fibre.This is a dedicated CCTV Network with 50 Cameras all streaming video into the Core (decoders connected to access switches)Each 2960G has 2 links to the Core/Distribution 3750G Switches, 1 to each switch - Gigabit.I'm running rapid-pvst on all switches, so spanning tree is blocking one of the ports and effectively halving the 2 gig bandwidth. Next year our customer is going to add in a further 50 - 60 cameras.After monitoring the current loading on the ports in use, we have suggested to the customer that the 2 connections to each should be Ether-channeled together. [code]
First interface takes commands no problem, keep getting the message that etherchannel cannot be configured across different switches in a stack when i try to put the second interface commands on.
View 8 Replies
View Related
Jul 19, 2011
I have a number of web sites that are currently being load balanced by CSS 11503s runninng 8x code. I was recently requested to configure HTTP --> HTTPS redirects on the CSS for every site. In the past, I have only configured the redirects for sites that had a requirement. Now it appears that the server teams want all content encrypted.
1) What impact will this have on the CPU?
2) What impact will this have on Memory utilization?
3) Is there a maximum nubmer on redirects?
4) Are there other things I should be concerned about?
View 3 Replies
View Related
Mar 24, 2013
i have two CSS-11503 in redundant mode running 8.20 code. We had an incident in our network where a layer 2 loop caused some high traffic through the CSS' and had to shutdown some network gear(including the CSS) to clear the problem. When the CSS' were powered back up, the SSL service was suspended, why this would occur? There rest of the config appeared normal. I am the only person on these boxes, the configs were written, and I have never had a reason to suspend the ssl service.
View 1 Replies
View Related
Oct 14, 2012
I know that CSRs cannot be generated with multiple names, but if the SAN is added after the cert is ordered from Geo Trust, Veri sign, etc. can the CSS support using the cert?
View 1 Replies
View Related
Jun 2, 2012
We now have a new requirement . We are replacing existing pair of CSS with ACE 4710 appliances. The problem here is that I can see from the configuration that some SSL certificate installed in CSS .Is it possible to transfer the existing SSL certificate from the 11503 to the ACE? Or, do we need to generate a new key pair and CSR on the ACE? Is there any document available to know the steps for the same.
View 2 Replies
View Related
May 21, 2012
We have several pairs of CSS11501 and 11503 in our network.This issue affects only one pair of CSS11503 in one of our data centres. [code] We use vrrp in one-armed mode for load balancing and they units have performed great for a number of years. We're obviously going to be migrating to ACE ... but not just yet.We have started to experience a problem with replicating the configurations between two CSS11503 in a pair.When running the commit-VipRedundConfig, it starts off happily enough, though slowly.Ending with "working" and the spinning cursor, even after 1 hour the script hasn't completed.We noted on the backup CSS that the APP configuration disappears during the process and I can't remember if this is normal behaviour.
Re-adding the app session configuration seems to interrupt the process, and when checking the configuration on the backup CSS approximately half of it is missing. Everything after the first owner is gone.
1. Configuration is too large, or just large enough to make the commit script take too long for realistic service.
2. Software bug?
3. Combination of both.
4. From now on manually add config to both CSS's and maintain it by process management.
View 5 Replies
View Related
Mar 20, 2012
Am trying to verify performance figures for ACE 4710 as EOL replacement for a CSS 11503 Am sure that the ACE 4710 smokes the CSS but have to complete the due diligence
Pulling figures from data sheets, release notes etc.. I have only come up with the followingIs there any further figures available for the ACE 4710 to fill in the blanks in table?
View 1 Replies
View Related
Apr 27, 2013
I have a single cisco 11503 load balancer.There is a single Banner student information system which is load balanced on it with Virtual ip 10.3.20.101 which is working fine without any issues .I am now trying to add an Oracle ERP application with virtual IP 10.3.20.230 and physical ips 10.3.19.22 and 10.3.19.23 all on port 8003.When I just make the group ERP-Apps-Grp active , the vitual ip address 10.3.20.230 is pingable , but when I make the the content Erp_IAT active it stops pinging. [code]
View 6 Replies
View Related
Sep 11, 2011
what is the "passdetect" command equivalent in CSS 11503 load balancer. software version 8.20.
View 3 Replies
View Related
Oct 4, 2011
I currently have a content group as follows;
content My_Group
add service blade1
add service blade2
add service blade3
vip address 1.2.3.4
advanced-balance arrowpoint-cookie
[code]...
So I have 3 blades which are proxy servers and user go first to an MS ISA server then the VIP of the CSS and then the rules processes them give them a blade and chuck them out onto the Internet.
I want to leave the above rule, but remove one blade create an additional content group with that blade and have it process requests for a particular site so, I would create the following
content My_Group2
add service blade3
vip address 1.2.3.4
advanced-balance arrowpoint-cookie
[code]...
So my question is can I do that having the same VIP's etc so if a request comes in and it matches www.thewebsite.com that the second content rule matches it 'better' and therefore processes it or would it still be caught by the "/*" content group. I don't want to create more VIPS as I have a real ache getting firewall rules done.
View 9 Replies
View Related
Jun 26, 2011
I'm not sure if my terminology is correct when using hairpinning but i was wondering if there is any special config needed when you try to access a content rule VIP from a server that's configured as a member of a source group on the same CSS?
So say i have a content rule with a VIP 20.20.20.20 and i also have two servers 192.168.1.1 and 192.168.1.2 that are part of a source group with VIP of 20.20.20.21. My problem at the moment is if from the servers 192.168.1.x i try to ping the other VIP 20.20.20.20 that's configured on the same CSS then it doesn't work and ping fails. The same happens with HTTP traffic to the 20.20.20.20 VIP.
I would have thought that the NAT of the source group would happen before the routing so the 192.168.1.x IP's would be natted to 20.20.20.21 and then passed over for routing where the CSS would see that the VIP 20.20.20.20 is local and it would send it on it's way.
I thought it might be ACL related but i increased the verbosity of acl logging and couldn't see anything in the logs.The source group works fine on it's own and from the CSS itself i can ping the 20.20.20.20 VIP fine. It just seems that from the source group members i can't ping the VIP.
View 1 Replies
View Related
Sep 26, 2011
what is the OID for See the hit status of the spefic VIP and RIP coming under the VIP .apeart from this CSS box having any module to moniter the hit status or VIP's and RIP's
View 2 Replies
View Related
