I know that CSRs cannot be generated with multiple names, but if the SAN is added after the cert is ordered from Geo Trust, Veri sign, etc. can the CSS support using the cert?
View 1 RepliesIs the XFF [URL] on the Cisco CSS 11503? If not, is it on the roadmap for a future code release?
View 1 Replies View Relatedi need the MIB object names for monitoring the processor and Memory Utilization of CSS 11503 with software version 7.50 Where can I find it?
View 5 Replies View RelatedAm I able to use an SSL cert in the proxy list for the same VIP but on a different port?
View 1 Replies View RelatedI have a number of web sites that are currently being load balanced by CSS 11503s runninng 8x code. I was recently requested to configure HTTP --> HTTPS redirects on the CSS for every site. In the past, I have only configured the redirects for sites that had a requirement. Now it appears that the server teams want all content encrypted.
1) What impact will this have on the CPU?
2) What impact will this have on Memory utilization?
3) Is there a maximum nubmer on redirects?
4) Are there other things I should be concerned about?
i have two CSS-11503 in redundant mode running 8.20 code. We had an incident in our network where a layer 2 loop caused some high traffic through the CSS' and had to shutdown some network gear(including the CSS) to clear the problem. When the CSS' were powered back up, the SSL service was suspended, why this would occur? There rest of the config appeared normal. I am the only person on these boxes, the configs were written, and I have never had a reason to suspend the ssl service.
View 1 Replies View RelatedWe now have a new requirement . We are replacing existing pair of CSS with ACE 4710 appliances. The problem here is that I can see from the configuration that some SSL certificate installed in CSS .Is it possible to transfer the existing SSL certificate from the 11503 to the ACE? Or, do we need to generate a new key pair and CSR on the ACE? Is there any document available to know the steps for the same.
View 2 Replies View RelatedWe have several pairs of CSS11501 and 11503 in our network.This issue affects only one pair of CSS11503 in one of our data centres. [code] We use vrrp in one-armed mode for load balancing and they units have performed great for a number of years. We're obviously going to be migrating to ACE ... but not just yet.We have started to experience a problem with replicating the configurations between two CSS11503 in a pair.When running the commit-VipRedundConfig, it starts off happily enough, though slowly.Ending with "working" and the spinning cursor, even after 1 hour the script hasn't completed.We noted on the backup CSS that the APP configuration disappears during the process and I can't remember if this is normal behaviour.
Re-adding the app session configuration seems to interrupt the process, and when checking the configuration on the backup CSS approximately half of it is missing. Everything after the first owner is gone.
1. Configuration is too large, or just large enough to make the commit script take too long for realistic service.
2. Software bug?
3. Combination of both.
4. From now on manually add config to both CSS's and maintain it by process management.
I only have configured load balancing on apache with a very simple setup. I have to deploy 2 applications on my clients environment that run inside jboss. One of these applications needs session to be sticky to work properly. The other does not.
In apache I can configure is the sticky parameter is true or false, based on the url, like /appA/* is sticky and /appB/* is not sticky. Can I do that in a CSS 11503? My client insists that it is impossible. That the CSS is only ip based.
I copied the configuration below from the manual: owner arrowpoint # content ruleWapSticky
Am trying to verify performance figures for ACE 4710 as EOL replacement for a CSS 11503 Am sure that the ACE 4710 smokes the CSS but have to complete the due diligence
Pulling figures from data sheets, release notes etc.. I have only come up with the followingIs there any further figures available for the ACE 4710 to fill in the blanks in table?
I have a single cisco 11503 load balancer.There is a single Banner student information system which is load balanced on it with Virtual ip 10.3.20.101 which is working fine without any issues .I am now trying to add an Oracle ERP application with virtual IP 10.3.20.230 and physical ips 10.3.19.22 and 10.3.19.23 all on port 8003.When I just make the group ERP-Apps-Grp active , the vitual ip address 10.3.20.230 is pingable , but when I make the the content Erp_IAT active it stops pinging. [code]
View 6 Replies View Relatedwhat is the "passdetect" command equivalent in CSS 11503 load balancer. software version 8.20.
View 3 Replies View RelatedI currently have a content group as follows;
content My_Group
add service blade1
add service blade2
add service blade3
vip address 1.2.3.4
advanced-balance arrowpoint-cookie
[code]...
So I have 3 blades which are proxy servers and user go first to an MS ISA server then the VIP of the CSS and then the rules processes them give them a blade and chuck them out onto the Internet.
I want to leave the above rule, but remove one blade create an additional content group with that blade and have it process requests for a particular site so, I would create the following
content My_Group2
add service blade3
vip address 1.2.3.4
advanced-balance arrowpoint-cookie
[code]...
So my question is can I do that having the same VIP's etc so if a request comes in and it matches www.thewebsite.com that the second content rule matches it 'better' and therefore processes it or would it still be caught by the "/*" content group. I don't want to create more VIPS as I have a real ache getting firewall rules done.
I'm not sure if my terminology is correct when using hairpinning but i was wondering if there is any special config needed when you try to access a content rule VIP from a server that's configured as a member of a source group on the same CSS?
So say i have a content rule with a VIP 20.20.20.20 and i also have two servers 192.168.1.1 and 192.168.1.2 that are part of a source group with VIP of 20.20.20.21. My problem at the moment is if from the servers 192.168.1.x i try to ping the other VIP 20.20.20.20 that's configured on the same CSS then it doesn't work and ping fails. The same happens with HTTP traffic to the 20.20.20.20 VIP.
I would have thought that the NAT of the source group would happen before the routing so the 192.168.1.x IP's would be natted to 20.20.20.21 and then passed over for routing where the CSS would see that the VIP 20.20.20.20 is local and it would send it on it's way.
I thought it might be ACL related but i increased the verbosity of acl logging and couldn't see anything in the logs.The source group works fine on it's own and from the CSS itself i can ping the 20.20.20.20 VIP fine. It just seems that from the source group members i can't ping the VIP.
what is the OID for See the hit status of the spefic VIP and RIP coming under the VIP .apeart from this CSS box having any module to moniter the hit status or VIP's and RIP's
View 2 Replies View RelatedI recently "inherited" a CSS 11503 - I've only used ACEs before - and I want to get HTTP keepalives working.To start, I created a test service:
lb-1# show run service sunbird-http-7025-test
!************************** SERVICE **************************
service sunbird-http-7025-test
port 7025
ip address 141.211.229.168
[code].....
I have a CSS 11503 with a basic content rule for TCP 10000 going to a few backend servers. I was looking into the default timeout values for flows and when testing using telnet the flow didn't terminate as expected?
For example, i have no 'timeout multiplier' specified in the config and when i look at the output of 'show flow-timeout default' it tells me the default 16 seconds timeout is in effect for *. With that in mind, i telnet to the content rule vip on TCP 10000 and on the backend server using wireshark i can see the TCP threeway handshake. With no data passing i'd expect the CSS to terminate this flow after 16 seconds.. yet it takes exactly 128 seconds before wireshark shows the RST and the flow is terminated. 128 being 8 times the default 16 second flow timeout.
If i try to force the connection to close early by specifiying 'flow-timeout-multiplier 2' in the content rule, or even a multiplier of 40, it still waits 128 seconds to close the telnet connection.
Is it possible on the CSS11503 to create a layer 5 content rule that matches a url "/*/_edit".
View 3 Replies View RelatedI have already raised this discussion on "LAN, Switching and Routing" group. But I guess this is the right group for my queries. So I am sending my queries in this group again.
We are using CSS 11503 with one 16FE line card. We have connected 3 servers with redundant link. So FE1-2 in Server1, FE 3-4 in Server2 and FE5-6 in Server3. Our system team has configured APA in their servers as they are using HP-Ux.
1) Do we need to do any configuration at line card.
2) Do we need to do ether-channel at loadbalancer end. if yes, can you share me any cisco doc on how to do it.
We have a pair of CSS 11503 installed in our DC. Stickiness is configured for one of the application since long back and was working pretty fine till last couple of months. Since last two months, we observed that CSS is not distributing sessions the way it suppose to be. Mostly, it forwards the session to same server even though request is coming from different sources. Once we refresh the sessions manually, it starts working fine. We have to do this exercise manually every alternate day.
View 1 Replies View RelatedI have 2 pair of 11501 switches and 1 pair of 11503 switches on 3 sites(LA, China, Taiwan).Each site has a pair of 1105x switch running as redundancy between them and is a standalone which will not interact with others.Recently a series of interfaces(ports) down happened to every active 1150x switches without any reason and log.Especially today, it happened to active switches at 5:39 AM meanwhile on 3 sites.
View 3 Replies View RelatedI am trying to get a sample command output of "show chassis inventory" for:
CSS 11501
CSS 11503
CSS 11506
I'm trying to design a CSS configuration that allows servers in the same vlan to be the source and destination of load-balanced traffic. My thought is to add two new vlans, one for the VIPs and one for the servers, then NAT the source IPs going from the LB to the servers.
Is this the right way to do it?I've never NATted using CSSs, so I wanted to verify what I'm thinking.Our current config trunks the vlans -
interface 1/1
trunk
vlan 1
default-vlan
vlan 555
[code]....
I want to deploy a high availability solution for web servers in two data centers. In the primary data center I have deployed a group of web server and I want two deploy additional servers in a secondary data center for disaster recovery and high availability. Reviewing the documentation, looks like the GSS4492 is the solution for my company needs but I am not sure if I have to implement just the GSS or if I need a ACE4700 integrated with the GSS?.
View 1 Replies View RelatedACE20 module with A2(3.3)I have tried to config a NAT-pool with two adresses, but only one is used.
View 6 Replies View RelatedI have a pair of ACE30 in Active/Standby mode. I can ssh to all active contexts. I can also ssh to all standby contexts except one.
View 6 Replies View RelatedThe below is the display that I get on the screen when i boot the device.There are two error's one is when the daughter card is found and device give us login access after which it reboot’s. The second is stated below (this is a screen copy of the error)
INIT: version 2.85 booting/mnt/cf/TN-CONFIG on /TN-CONFIG type ext3 (rw,sync,loop=/dev/loop0)/mnt/cf/TN-CERTKEY-STORAGE on /TN-CERTKEY-STORAGE type ext3 (rw,sync,loop=/dev/loop1)/mnt/cf/TN-LOGFILE on /TN-LOGFILE type ext3 (rw,sync,loop=/dev/loop2)/mnt/cf/TN-HOME on /TN-HOME type ext3 (rw,sync,loop=/dev/loop3)/mnt/cf/TN-COREFILE on /TN-COREFILE type ext3 (rw,sync,loop=/dev/loop4)insmod: error inserting
[Code]...
I'm working on a small scale Cisco WAAS deployment. I want to know if it's possible to use the entry level Cisco WAVE-294-K9 as Central Manager.Also about licensing, does this appliance model come with the enterprise level license
View 2 Replies View RelatedDo you know if it is possible in ACE 4710 appliance to configure a SIP TLS ?The SIP probe we have in the configuration guide it is only for clear text. for Lync 2013 we need to establish first a TLS session and then within it, send an SIP request..IS it possible in any version? I tried also to configure a HTTPS probe but it fails as it sends a GET which the Lync SIP server doesn't understand.
View 1 Replies View RelatedI want to use the ACE blade in CAT6500 to loadbalancing SYSLOG events towards (SIEM) collectors. Servers and network devices will sent there syslog messages to different collectors after being loadbalanced by ACE. I was just wondering, since a lot of clients are going to sent there complete syslog events to the VIP and thus introducing a high connection rate. (+/- 200.000 CPS) According to the specs, the ACE blade has a limitation of 325.000 connection per second. I suppose this is a limitation at device level. (not on a per context basis, and does that include both TCP and UDP packets?) Could the UDP BOOST feature might come in handy allowing very high rate UDP syslog packet loadbalancing?
View 2 Replies View Relatedif ACE SM in L2 mode need the default gateway? We're running v. 3.2a.
View 8 Replies View RelatedWe are evaluating the one-arm design for the ACE 4700 and need some clarifications:
1. Are there any limitations in the one-arm design and the SSL offloading
2. Can the ACE be configured with an IN and an OUT vlan to the router
CLIENT -> Router -> ACE IN -> ACE OUT -> Router -> Server Vlan
so that the SSL and the clear text traffic is in a separate Vlan?
3. In some sample configuration i saw SNAT configuration on the ACE to modify the client IP. This i assume is for instructing the return traffic from the server to go through ACE? Using SNAT we eliminate the requirement for NAT or PBR on the router? Will i still be able to insert the client IP address after the SSL offload?
Will ACE 4710 support for IPS features?
View 1 Replies View Related