I'm using cisco LMS 4.0, I've discovered the device and next plan is to collect the device configuration.I would like to know, How I can collect the configuration for single device.What configuration changes required on my LMS & Cisco device.
View 1 RepliesI'm using LMS 4.0.1 and VPN hw client 3002 with software 4.7.2.L.I'm not able to collect the first configuration and sync jobs end with these errors.
View 2 Replies View RelatedWe have just installed lms 4.2 and are having problems collecting config and inventory from ws-svc-wism2-k9. The response from TAC was that this is not supported. And it also says this in
[URL]
Is this really the case ? Will there be released packeges to support this. It would be really useful if this was supported in lms4.2.
I have multiple campuses and a Central Admin...I've created Groups for all, except I need a few devices within Central to be available to the Campus Admins... (ie..a Cisco WCS System) How do I allow a device to be put into multiple NDG groups?
View 1 Replies View RelatedWe have LMS Prime 4.2. I know how to view the running config on a single device. How do I run a report that will pull all the running configs of all my devices in one report? I'd be able to same them as one big pdf or text file. ]
View 1 Replies View RelatedRegion : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.31 Build 130319 Rel.57876n
ISP : Antel
I have a WDR4300 which works perfect with all devices in my house, but in my personal notebook (samsung 530U4B) wireless transfer speed is very slow in 2.4 GHz mode. 5.0 ghz works fine. I've tried everything, but I can not get good performance. at this moment I have to use a 741nd working with my wdr4300 in wds mode to use 2.4 ghz band properly.
3750 can not support multiple subnets in it's DHCP server pool config.
Is this an issue that can be fixed with a different iOS or is there a different Cisco switch that I can replace the 3750 with that will handle multiple subnets within an individual pool?
In the LAN network 4507R as core switch configured with several vlans.One vlan connects to the dual homed routers which in turn connecting to the single isp. I need to configure the HSRP for the internal vlans and the same time to use the load balancing or failover using the dual homed routers to the isp.
View 7 Replies View RelatedWe have recently aquired a remote location which has a pre-existing flat network (172.16.X.X/16). Before we are able to convert them over to our new IP scheme, they have a need to have wireless connectivity on site. We have 4 1142's which I need to configure for them. I have experience configuring WLC's and autonomous AP's for networks with multiple vlans but have never configured AP's for a flat, single subnet network. I need to configure them for either guest access (internet only) or corporate access to network resources with radius authentication. Do I configure a native vlan as I would for a typical multi vlan network? Do I configure the switch port as an access port as opposed to a trunk beacause of the lack of layer 3? I basically need a sample configuration for this situation.
View 1 Replies View RelatedI am using LMS3.2, but it is not able to collect running config, and startup config from asa 5520. LMS is able to collect all syslog from asa.
View 4 Replies View RelatedThere are 3 newly installed Cat4506-E.SSH and SNMPv3 access are verificated. Devices are managable in every way only the inventory is missing.If I try to collect manually then they fail but I can't figure it out why.
View 2 Replies View RelatedI have turned on 'Local log' and 'output blocking event log' on my WRVS4400N v2 with latest fw.When I am clicking 'view log' button I can't see anything in empty fields. When I am trying to change logs genre I have empty fields all time.
View 1 Replies View RelatedHow can I collect the data about the traffic on my Cisco 2960S? Have I use only the snmp? Any workaround for simulate a netflow? The IOS c2960s-universalk9-mz.150-1.SE2.bin.
View 2 Replies View Relatedi have an issue for collect data on adapter 1, that don´t collect data but see that adapter 2 if collect data on module 4.
monitor session 1 source vlan 102 rx
monitor session 1 destination analysis-module 4 data-port 1
monitor session 2 source vlan 106 rx
monitor session 2 destination analysis-module 4 data-port 2
I reconfigured newly monitor and continues with that issue. Always ok by data-port 2.
- show version Cisco 6513
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
. show version NAM
NAM application image version: 3.5(1b)
- sh module
Ports Card Type Model
----- -------------------------------------- ------------------
8 Network Analysis Module WS-SVC-NAM-2
Hw Fw Sw Status
------ ------------ ------------ -------
2.0 7.2(1) 3.5(1b) Ok
I have 10 AIR-LAP1131AG-A-K9 connected to a 4402 controller. I have a couple of questions:
- When I go into CONFIGURE/ACCESS POINT, one of the AP's has the message "**Configuration is different on the Device**". How do I connect directly to the device to check the settings? I tried to telnet but that didn't work.
- Are these access points capable of acting as a DHCP server? If so, where can I check this setting? I have workstations that are unable to pull an IP address from my DHCP server running on a Windows server. I want to make sure the AP's and/or the controller are not the issue. The clients see the SSID and the signal is strong, but when they connect they get limited network connectivity message and the IP addr is 169.254.97.123 (which is wrong).
Yesterday, myself and local support team has been engaged to perform troubleshooting the issue of some web site accessing .Mos of this case is cased by MTU issue, So, I've tried to configure the following configuration on interface tunnel 0.Device: Cisco 7609 with IOS s72033-adventerprisek9_wan-mz.122-18.SXF8.bin
I've tried to figure out what the supporting command after 'ip tcp' in tunnel 0 and following likes..ip tcp ?compression-connections Maximum number of compressed connectionsheader-compression Enable TCP header compression.there is no such command about 'ip tcp adjust-mss.So, my questions is that what is the replace command for 'ip tcp adjust-mss' ? Is this only support on Router? such as Cisco 7200. or not, to take effect same functional on C7609, what is the command for that?
Is it possible to create a job what automatically export the devices configs that are in the folder CSCOpxfiles medemushadow? It would be wonderdul if CW could export the .cfg files into a .rar and send in email or something like this.
View 1 Replies View RelatedHow do i copy the configuration file from a switch to a storage device (USB)
View 1 Replies View RelatedI have a problem exporting the config from a 1112 appliance. It does not boot up properly. GUI logon and authentication is not possible. I can console and SSH to it but the only thing i get is the commands below and nothing else.
login as: admin
admin@10.10.1.126's password:
Last login: Wed May 30 11:11:42 2012 from jsmith
Could not chdir to home directory /home/admin: No such file or directory
acs>
API called before initialised at V:ismg_israel_acsAcsEndPointCoreendpoint.cpp:395
Command Description
----------------------------------------------------
? List commands
exit Log off
help List commands
csutil -dumpadmin Dump Admin Audit Information
csutil -dumpgroups Dump Group Audit Information
csutil -dumpusers Dump User Audit Information
csdbsync -syncnow RDBMS synchronization
i did a reset on my asa by stopping the boot process because i could not remember what my enable password was, i had no problems with the reset the asa came backup as it should and i started configuring the device again. My problem is when the device is powered off and back on i lose all configuration that were made, i save the changes with "write me" before the restart and they are still being over wrote.
View 4 Replies View Relatedwe just replace 6500 with N7K, after migration there're some device (server,pc,printer) change its ip address configuration (subnet and gateway) by it self. can N7K did it?
View 6 Replies View RelatedWhen trying to view the status in the Monitor tab and the Config tab after you log in to the ACE 4710 Device Manager A5 (1.2) management GUI tool, I could not retrieve the status data and the following message appeared.
"Faild to upload Adimn configuration: There is error in loading configuration: Error in loading RMO config from DB:The given index XXXXXXXXX.bak does not match table index definition"
Other features include all normal, so I can get information by using the CLI.In addition, this configuration is redundant in the Primary / Secondary, this event occurs only on the Primary.
Other:-XXXXXXXXX.bak is a backup that you created in the checkpoint, and it does not already exist.
-When I'm logged on to the GUI, the above message is displayed in the status bar always.
-It was not recovered by ACE restart it.
-When I try to create the same configuration in a different environment, it did not reproduce.
This is IOS 15.1(4)M3 on a 1921 router. The LAN is 192.168.42.1/24. (DHCP config is further down.) We have a small range that we want to assign via DHCP to devices; .200 through .220 . At the same time, we have a handful of Macintosh systems to which we want to assign a specific address that is not in that 200-220 range. I don't want to configure the assignment based on the Ethernet MAC addresses because these systems might connect via UTP or wireless; that is to say, they have more than one MAC address. They only ever connect using one interface/MAC address at a time, but it's their choice; in some areas wi-fi is available, and in some areas they have to cable-up.
The Mac OSX network settings has a field for "DHCP Client ID". It would be much easier to tell the users of these systems to put their Mac's name in the Client ID field for both their wired and wireless DHCP configs. (As opposed to having them all lookup, and then give me their Ethernet MAC addresses for both of their interfaces.) I tried this with my Mac's (named "shrike") wi-fi interface, but I don't get the 192.168.42.14 address that I expected. I get an address from the .200 to .220 range.
Here's the DHCP-related config from the router:
router#sh run | s dhcp
ip dhcp excluded-address 192.168.42.1 192.168.42.199
ip dhcp excluded-address 192.168.42.221 192.168.42.254
ip dhcp pool OurOffice
network 192.168.42.0 255.255.255.0
[code]....
Is "client-name" the wrong place to configure the DHCP Client ID?
This is regarding CISCO logging configuration.We palnned to implement enable logging on all the cisco nexus switchs.we are running HP arc sight in our DC this device monitor all the CISCO devices.We want to enable logging with this Arc sight device.Just I would like to know about config commands for Nexus device, what is the command to enable logs which is include "who is login & logout?, interface down information?,who was did conf t ? & every logs"
View 8 Replies View RelatedWe are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies View RelatedMy BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies View RelatedThe problem: I need to track a bus from city to city in real time.I'm thinking of a gps device without screen or apps, it only sends the current location to a server. Is this possible? What device can be useful?
View 1 Replies View RelatedI am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
I have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem. So, out with the paperclip to do the big reset, causing me to lose my configuration. When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams. Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP. I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either. I tried EVERYTHING. Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move. UPnP had always been checked off in the router. So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?
View 2 Replies View RelatedQuestion: how would STP or RSTP behave in a star topology with a hub in the middle?i.e. you have four switches all linked to the same central hub. Single links, no loops.Each switch would then get BPDUs from everybody.Going by theory, it should be OK since it still sees the root's BPDU and will see the link to the hub as the root port, despite presence of other BPDUs from other switches? No different from receiving an inferior BPDU from an upstream switch and a superior BPDU from a further upstream root switch.I guess I could lab it by turning off spanning tree on a switch to simulate a hub? I've never previously had to deal with STP issues where there are hubs that aren't strictly point to point bridging so to speak (ok they're not bridging but you get the drift).I've got a scenario I'm examining at the moment where this is the topology, except all switches have bpdufilter running hence effectively no spanning tree. I'm curious to know what would happen should I remove the bpdufilter.I realise there is zero benefit in spanning tree in this instance as I don't have any redundant loops to fall back on, but I'm reluctant to turn off STP on those vlans (since obviously theres stuff behind those switches). The BPDUfilter method seems like an elegant solution but I wonder if its actually necessary.(the hub is actually a VPLS mesh, most sites terminate PE to CE router but I'm playing around with switches as the termination points – run our own Q in Q, split vlans off before it gets to layer 3 as separation, etc.)
View 1 Replies View RelatedI have a client that requires a single router with POE for placement at an economical price. I was considering the Linksys WAPPOE12, but that is discontinued. What would work with that router?
View 2 Replies View RelatedWe are trying to upgrade our ASR1006 with single RP. We got an Warning message as "superpackage install over superpackage not allowed on active RP"
how to do the upgrade properly?
I have got a cisco 1841 router. I need to do many nat. I have got a lots of virtual interface on this router. How many nat inside and outside does it supports ? Can I do more than one nat insdie and outside in different virual interfaces on the same single router.
View 2 Replies View Related