Cisco :: LMS 3.2 Is Able To Collect All Syslog From ASA 5520
Dec 27, 2011I am using LMS3.2, but it is not able to collect running config, and startup config from asa 5520. LMS is able to collect all syslog from asa.
View 4 RepliesI am using LMS3.2, but it is not able to collect running config, and startup config from asa 5520. LMS is able to collect all syslog from asa.
View 4 RepliesWe started getting the below syslog messages from one of our ASA5520 which was recently upgraded to 8.4(2). Any bugs on 8.4(2) that cause this or its simply the RAM failure?
%ASA-3-105010: (Primary) Failover message block alloc failed
%ASA-3-321007: System is low on free memory blocks of size 1550 (0 CNT out of 18709 MAX)
I'm trying to configure an ASA firewall (FW2) for syslog and tacacs and am experiencing strange behavior. Both the syslog and ACS server are on the inside of another firewall (CoreFW). Whenever a log message is generated on FW2 the request is dropped by CoreFW and message '%ASA-4-313004: Denied ICMP type=0, from laddr FW2 on interface outside-b2b to syslog01: no matching session' is displayed. The same thing occurs for tacacs.
It appears that the syslog and ACS requests are generating ICMP echo replies, which the core firewall drops since no session exists on a lower security interface. I have access lists configured on CoreFW to allow the syslog and tacacs requests.
FW2 is running asa825-k8.bin, CoreFW is asa824-k8.bin
I've just taken over a new network with a Cisco ASA5520. Everything is working fine, except I am being bombarded with 106001 alerts from a few internal hosts to one specific internal host. The description in general is "Inbound TCP connection denied from 10.1.0.1 to 10.1.0.5 - both of those are valid internal hosts and the TCP ports are also valid. I tried looking at the log and getting it me to tell me which rule was causing these alerts, but it just came back with 'It's not possible for these type of alerts'
- How is it possible for the ASA to even pick up on this when, in theory, the source host wouldn't be going near the ASA since it's on the same subnet?
- What might be causing this?
- How can I turn it off!! (I guess that'd be fixed by point 2)
Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies View RelatedRecently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies View RelatedAny step by step guide to setup syslog for site to site VPN.(in ASA 5520)Just send me the step to monitor site to site vpn using that in ASA 5520.
View 2 Replies View RelatedThere are 3 newly installed Cat4506-E.SSH and SNMPv3 access are verificated. Devices are managable in every way only the inventory is missing.If I try to collect manually then they fail but I can't figure it out why.
View 2 Replies View RelatedI have turned on 'Local log' and 'output blocking event log' on my WRVS4400N v2 with latest fw.When I am clicking 'view log' button I can't see anything in empty fields. When I am trying to change logs genre I have empty fields all time.
View 1 Replies View RelatedI'm using LMS 4.0.1 and VPN hw client 3002 with software 4.7.2.L.I'm not able to collect the first configuration and sync jobs end with these errors.
View 2 Replies View RelatedWe have just installed lms 4.2 and are having problems collecting config and inventory from ws-svc-wism2-k9. The response from TAC was that this is not supported. And it also says this in
[URL]
Is this really the case ? Will there be released packeges to support this. It would be really useful if this was supported in lms4.2.
I'm using cisco LMS 4.0, I've discovered the device and next plan is to collect the device configuration.I would like to know, How I can collect the configuration for single device.What configuration changes required on my LMS & Cisco device.
View 1 Replies View RelatedHow can I collect the data about the traffic on my Cisco 2960S? Have I use only the snmp? Any workaround for simulate a netflow? The IOS c2960s-universalk9-mz.150-1.SE2.bin.
View 2 Replies View Relatedi have an issue for collect data on adapter 1, that don´t collect data but see that adapter 2 if collect data on module 4.
monitor session 1 source vlan 102 rx
monitor session 1 destination analysis-module 4 data-port 1
monitor session 2 source vlan 106 rx
monitor session 2 destination analysis-module 4 data-port 2
I reconfigured newly monitor and continues with that issue. Always ok by data-port 2.
- show version Cisco 6513
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
. show version NAM
NAM application image version: 3.5(1b)
- sh module
Ports Card Type Model
----- -------------------------------------- ------------------
8 Network Analysis Module WS-SVC-NAM-2
Hw Fw Sw Status
------ ------------ ------------ -------
2.0 7.2(1) 3.5(1b) Ok
when we try to configure syslog to run over tcp it seems Cisco routers (12.4) do not send proper messages as syslog server does not record anything!Tested with syslog-ng (Linux) and Kiwi (windows) and both syslog servers have the same problem.These are some indications of the possible syslog tcp problems:
[URL]
Apparently Cisco ASA (8.2) seem to process this well!
I have an issue with rme 4.2 from LMS 3.1 When I try to generate a syslog report this shows me nothing. I locate SyslogCollector.log file and I see sometnig wrong.
View 4 Replies View RelatedI am only able to get InfoAlarm messages sent to via email notifications.My switch is sending logs to Cisco Works.Example:
13. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 UNBUNDLE Interface GigabitEthernet1/4 left the port-channel Port-channel2 *
14. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 BUNDLE Interface GigabitEthernet1/4 joined port-channel Port-channel2
But I only recieve infoalarm messages:
ALERT ID = 00000UE
TIME = Fri 04-Apr-2008 11:04:00 PST
STATUS = Active
SEVERITY = Informational
MANAGED OBJECT = 10.10.0.1
MANAGED OBJECT TYPE = Switches and Hubs
EVENT DESCRIPTION = 10.10.0.1: Cisco Configuration Management Trap:InformAlarm; 10.10.0.1: Authentication Failure:MinorAlarm;
My switch is setup as:
logging source-interface Loopback0
logging 10.10.100.111
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps syslog
I do not recieve critical or warning syslog messages.
I have a WCS working on version 7.0.172.0.Is there a way to send the alarms produced by WCS to another Syslog Server?
View 4 Replies View RelatedI have a new install of LMS 4.2 on a virtual appliance. No syslog messages are getting into LMS. They are being received by the server, but are showing up in /var/adm/CSCOpx/log/dmgtd.log, and aren't getting processed by SyslogAnalyser.
View 3 Replies View RelatedI received a syslog message on my cisco 3845 router, what is that message mean. 11 13:36:06.265 UTC: ASSERTION FAILED: file "../les/if_ng_dslsar_tx.c", line 385
View 2 Replies View RelatedI have a 6509 on my network and also have LMS4.1 for management. My 6509 is listed in my lms as a device. The config is in LMS. But I am not getting any syslog messages in LMS for my 6509. I have logging turned on and I have my LMS server listed in the config using the logging IP address command. What could be missing that would prevent the syslog messages from showing up in LMS. I have other devices that send syslog messages fine.
View 2 Replies View RelatedI am trying to setup syslog server on LMS 4.0.Everything seems to be working fine but I have a lot of stragne logs in my syslog.log file.Every single day I receive logs like :
Mar 05 09:31:03 127.0.0.1 100: <30> dmgt[1136]: 3007(I):Started application(1015) "e:CSCOpxincwjava.exe -cw:jre lib/jre -cp e:CSCOpxMDC omcatsharedlibMICE.jar;e:CSCOpxMDC omcatsharedlibNATIVE.jar;e:CSCOpxMDC omcatsharedlibjdom.jar;e:CSCOpxMDC omcatsharedlibxalan.jar;e:CSCOpxMDC omcatsharedlibxerces.jar;e:CSCOpxMDC omcatcommonlibservlet.jar;e:CSCOpxMDC omcatsharedlibcastor-0.9.5.jar;e:CSCOpxMDC omcatsharedlibcastor-0.9.5-xml.jar;e:CSCOpxlibclasspath;e:CSCOpxwwwclasspath;wwwclasspathvbjorb.jar;MDC omcatwebappsupmWEB-INFclasses;libjrelibendorsedjacorb.jar;MDC omcatwebappsupmWEB-INFlibctm.jar;MDC omcatwebappsupmWEB-INFliblog4j.jar;MDC omcatwebappsupmWEB-INFlibjep-3.2.0.jar;MDC omcatwebappsupmWEB-
[code]....
I dont want to get any logs from 127.0.0.1. Is it possible to filter out logs from server ?
It appears that there are two different types of log information generated by the WLC-5508. The stuff that can be sent directly to syslog seems to be very basic while most of the good log information is sent via snmp trap. Does this setup to log to a SIEM in a manner that gives a good security view into the wireless controller?
View 4 Replies View RelatedLMS 4.1 is not showing any valid syslog messages, only invalid messages. Is there anything different in 4.1 that needs to be set?
View 2 Replies View RelatedMy Cisco devices send syslog messages to LMS but it wont`t show any messages from device. Older LMS 3.2 and other collector showe all syslog messages. What to do with LMS 4.0.1?
View 2 Replies View RelatedI want send ACS logs to a syslog server .I have configured syslog under System Administration --> Configuration -->Remote Log Targets .
Name : Syslog Server
IP : x.x.x.x
Port : 514
Facility Code:Local 6
Maximum length :1024
I have open the respective ports also in firewall .But Syslog server is not getting any logs from ACS .I have another log target ,which is ACS secondary server to collect the log from primary and secondary with below config.whch is working fine
Name :Logcollector
IP : x.x.x.x
Port : 20514
Facility Code:Local 6
Maximum length :1024
I have a newly installed LMS 4.1 that had the Syslog feature working for a while.
Recently, the Syslog is no longer displaying any records (neither new or old messages).
Below are the steps I have tried to troubleshoot the problem:
- Installed wireshark : Syslog messages are being received by the LMS server on time
- In the Syslog.log file, I can see that all the Syslog messages are being logged properly
- I tried to disable all the "Syslog Message Filters" but nothing changed
In the SyslogCollector.log, I can find the below logs:
NMSROOT is C:/PROGRA~2/CSCOpx
propFileC:/PROGRA~2/CSCOpxMDC omcatwebapps
meWEB-INFclassesC:PROGRA~2CSCOpxMDC omcatwebapps
[Code]....
I get the following error:
SyslogCollector - [Thread: SyslogObjectForwarder] ERROR, 27 Mar 2012 09:02:12,254, Could not send syslogs, removing the subscriber...Connection refused: connect
SyslogCollector - [Thread: SyslogObjectForwarder] ERROR, 27 Mar 2012 09:03:15,223, Could not send syslogs, removing the subscriber...Connection refused: connect
Syslog subscription seems ok but syslog messages are dropped and not forwarded:
I attached SyslogCollector.log, SyslogAnalyzer.log, AnalyzerDebug.log
I have a small problem with a lot of invalid syslog messages in LMS 3.2. Something about 30% of all messages are invalid.
Is there any posibility to get out from which devices those messages are?
Is it a big problem for the application if there are such a lot of invalid messages? I have a lot of devices in my LMS and don't want to get high load because of such unneeded messages.
I'm getting the Syslog messages frequently on daily basis.
View 4 Replies View RelatedIs there a way to debug syslog messages? Something like "debug ip syslog"?
View 11 Replies View RelatedI am trying to log every connection (Build, deny, etc).But for some reason I don't see them sh log.
[Code]...
my LMS 4.2, syslog collector on LMS doesnt working even service syslog collector running normaly and also i saw in syslog_info is working to collect syslog from all router but not show up in dashboard monitoring.I have setting on every router to logging (ip address LMS) but on LMS no any syslog from router can collect.i did a selftest from LMS there are all PASS except nslookup fail, it is has relation with syslog not show up on dashboard?
View 5 Replies View Related