It appears that there are two different types of log information generated by the WLC-5508. The stuff that can be sent directly to syslog seems to be very basic while most of the good log information is sent via snmp trap. Does this setup to log to a SIEM in a manner that gives a good security view into the wireless controller?
View 4 RepliesI am trying to log every connection (Build, deny, etc).But for some reason I don't see them sh log.
[Code]...
How to set up logging of commands on syslog server ? (cisco nexus 7010)
View 2 Replies View RelatedI found a new bug in cisco IOS 15.1(4)M3 when running EEM script with syslog event detector.If system logging performed using the "logging discriminator" and run concurrently EEM script with syslog event detector, then Cisco router crash and goes to reboot.
Cisco ISR G2 3925E.
I am sending TACACS administration logging to a syslog server. When the messages show up on the syslog server, they are 5 hours ahead of the actual time. Time on the ACS is correct - local logging shows the correct time. Time on the syslog server is correct...all other devices/systems sending syslog messages to it are coming through with the correct time. why the ACS syslog messages would be 5 hours ahead?
View 3 Replies View RelatedWe have a firewall service environment where logging is handled with UDP at the moment. Recently we have noticed that some messages get lost on the way to the server (Since the server doesn't seem to be under huge stress from syslog traffic). We decided to try sending the syslog via TCP. You can imagine my surprise when I enabled the "logging host <interface name> <server ip> tcp/1470" on an ASA Security context and find out that all the connections through that firewall are now being blocked. Granted, I could have checked the command reference for this specific command but I never even thought of the possibility of a logging command being able to stop all traffic on a firewall.
The TCP syslog connection failing was caused by a mismatched TCP port on the server which got corrected quickly. Even though I could now view log messages from the firewall in question in real time, the only message logged was the blocking of new connections with the following syslog message: "%ASA-3-201008: Disallowing new connections."
Here start my questions:
- New connections are supposed to be blocked when the the TCP Syslog server are not reachable. How is it possible that I am seeing the TCP syslog sent to the server and the ASA Security Context is still blocking the traffic?
- I configured the "logging permit-host down" after I found the command and it supposedly should prevent the above problem/situation from happening. Yet after issuing this command on the Security Context in question, connections were still being blocked with the same syslog message. Why is this?
- Eventually I changed the logging back to UDP. This yet again caused no change to the situation. All the customer connections were still being blocked. Why is this?
- After all the above I removed all possible logging configurations from the Security Context. This had absolutely no effect on the situation either.
- As a last measure I changed to the system context of the ASA and totally removed the syslog interface from the Security Context. This also had absolutely no effect on the situation.
At the end I was forced to save the configuration on the ASAs Flash -memory, remove the Security Context, create the SC again, attach the interfaces again and load the configuration from the flash into the Security Context. This in the end corrected the problem. Seems to me this is some sort of bug since the syslog server was receiving the syslog messages from the SC but the ASA was still blocking all new connections. Even the command "logging permit-host down" command didn't wor or changing back to UDP.
It seems the Security Context in question just simply got stuck and continued blocking all connections even though in the end it didn't have ANY logging configurations on. Seems to me that this is quite a risky configuration if you are possibly facing cutting all traffic for hundreds of customers when the syslog connection is lost or the above situation happens and isn't corrected by any of the above measures we took (like the command "logging permit-host down" which is supposed to avoid this situation altogether).
logging buffered 4096 warnings The above causes router to log all the events with severity level 4 or below in buffer.What about logging console warnings command?will the above command cause router to send log messages with severity level 4( warnings severity level) to console only or will the router send all the log messages with severity level 4 or below to console ?
View 3 Replies View RelatedI'm looking to configure a syslog server for all of my cisco device logging. I've had a look at CNA and can't find any options to define a syslog server for my switches.
What's the best way to define a syslog server and the severity of the notifications? Also, i'm looking to clear all previous Syste mmessages fon my devices?
I'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
For WLC 5508 software version 7.0.235.0, which command is needed to get the WLC send syslog messages everytime a wireless client associate and desassociate?
View 2 Replies View RelatedAdd the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies View RelatedRecently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies View RelatedI'm encountering what I think is an issue on logging system on FW ASA 5520 - Asa Version 8.4(2), ASDM version 6.4(5). When I disabled the logging inside a rule from ASDM, or from console with the "log disable" option inside ACL, If I check in ASDM logging real time window I continue to see all the entry related to disabled rules. This is a correct behaviour about ASA logging ? How I can "hide" the entry related to disabled rules (this is what I need for troubleshooting purposes) ?
View 1 Replies View Relatedwhen we try to configure syslog to run over tcp it seems Cisco routers (12.4) do not send proper messages as syslog server does not record anything!Tested with syslog-ng (Linux) and Kiwi (windows) and both syslog servers have the same problem.These are some indications of the possible syslog tcp problems:
[URL]
Apparently Cisco ASA (8.2) seem to process this well!
Doing systems work now, but today I am busy troubleshooting a site-to-site VPN endpoint on an ASA.
I find it hard to believe, but I've spent over an hour just trying to login and get some debugging info on the key exchange, etc. It seems almost impossible. I've tried "term mon", "debug crypto isakmp", "logging console", "debug crypto ipsec", and a gazillion other things.
Can't I just see the debug info for the site-to site VPN?
I have an ACS 5.2 VM that went down during an ESX host issue. Since it has no VMWare tools, it didn't migrate to another host very nicely. When the box came up, I had to delete the Virtual nic and re-add it and then set up the IP info again to get the VM communicating on the network.Currently the ACS box is not logging anything. There are no logs visable. What can I do to check why there are no logs visable? Authentication is working because wireless uses are still getting on the wireless network, but there are no logs that show passed or failed attempts.
View 4 Replies View RelatedGot this little RV22OW router working at home. I thought this box woudl provide me the facilities i needed t be able to securly manage a home with several expert children.
What I need to do now is to configure URL logging. i.e I want to log the URL's going out of the LAN. Dont want to block them neccessarily. Just want to log whats going on.
I have an issue with rme 4.2 from LMS 3.1 When I try to generate a syslog report this shows me nothing. I locate SyslogCollector.log file and I see sometnig wrong.
View 4 Replies View RelatedI am only able to get InfoAlarm messages sent to via email notifications.My switch is sending logs to Cisco Works.Example:
13. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 UNBUNDLE Interface GigabitEthernet1/4 left the port-channel Port-channel2 *
14. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 BUNDLE Interface GigabitEthernet1/4 joined port-channel Port-channel2
But I only recieve infoalarm messages:
ALERT ID = 00000UE
TIME = Fri 04-Apr-2008 11:04:00 PST
STATUS = Active
SEVERITY = Informational
MANAGED OBJECT = 10.10.0.1
MANAGED OBJECT TYPE = Switches and Hubs
EVENT DESCRIPTION = 10.10.0.1: Cisco Configuration Management Trap:InformAlarm; 10.10.0.1: Authentication Failure:MinorAlarm;
My switch is setup as:
logging source-interface Loopback0
logging 10.10.100.111
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps syslog
I do not recieve critical or warning syslog messages.
I have a WCS working on version 7.0.172.0.Is there a way to send the alarms produced by WCS to another Syslog Server?
View 4 Replies View RelatedI have a new install of LMS 4.2 on a virtual appliance. No syslog messages are getting into LMS. They are being received by the server, but are showing up in /var/adm/CSCOpx/log/dmgtd.log, and aren't getting processed by SyslogAnalyser.
View 3 Replies View RelatedI received a syslog message on my cisco 3845 router, what is that message mean. 11 13:36:06.265 UTC: ASSERTION FAILED: file "../les/if_ng_dslsar_tx.c", line 385
View 2 Replies View RelatedI have a 6509 on my network and also have LMS4.1 for management. My 6509 is listed in my lms as a device. The config is in LMS. But I am not getting any syslog messages in LMS for my 6509. I have logging turned on and I have my LMS server listed in the config using the logging IP address command. What could be missing that would prevent the syslog messages from showing up in LMS. I have other devices that send syslog messages fine.
View 2 Replies View RelatedI am trying to setup syslog server on LMS 4.0.Everything seems to be working fine but I have a lot of stragne logs in my syslog.log file.Every single day I receive logs like :
Mar 05 09:31:03 127.0.0.1 100: <30> dmgt[1136]: 3007(I):Started application(1015) "e:CSCOpxincwjava.exe -cw:jre lib/jre -cp e:CSCOpxMDC omcatsharedlibMICE.jar;e:CSCOpxMDC omcatsharedlibNATIVE.jar;e:CSCOpxMDC omcatsharedlibjdom.jar;e:CSCOpxMDC omcatsharedlibxalan.jar;e:CSCOpxMDC omcatsharedlibxerces.jar;e:CSCOpxMDC omcatcommonlibservlet.jar;e:CSCOpxMDC omcatsharedlibcastor-0.9.5.jar;e:CSCOpxMDC omcatsharedlibcastor-0.9.5-xml.jar;e:CSCOpxlibclasspath;e:CSCOpxwwwclasspath;wwwclasspathvbjorb.jar;MDC omcatwebappsupmWEB-INFclasses;libjrelibendorsedjacorb.jar;MDC omcatwebappsupmWEB-INFlibctm.jar;MDC omcatwebappsupmWEB-INFliblog4j.jar;MDC omcatwebappsupmWEB-INFlibjep-3.2.0.jar;MDC omcatwebappsupmWEB-
[code]....
I dont want to get any logs from 127.0.0.1. Is it possible to filter out logs from server ?
LMS 4.1 is not showing any valid syslog messages, only invalid messages. Is there anything different in 4.1 that needs to be set?
View 2 Replies View RelatedI am using LMS3.2, but it is not able to collect running config, and startup config from asa 5520. LMS is able to collect all syslog from asa.
View 4 Replies View RelatedMy Cisco devices send syslog messages to LMS but it wont`t show any messages from device. Older LMS 3.2 and other collector showe all syslog messages. What to do with LMS 4.0.1?
View 2 Replies View RelatedI want send ACS logs to a syslog server .I have configured syslog under System Administration --> Configuration -->Remote Log Targets .
Name : Syslog Server
IP : x.x.x.x
Port : 514
Facility Code:Local 6
Maximum length :1024
I have open the respective ports also in firewall .But Syslog server is not getting any logs from ACS .I have another log target ,which is ACS secondary server to collect the log from primary and secondary with below config.whch is working fine
Name :Logcollector
IP : x.x.x.x
Port : 20514
Facility Code:Local 6
Maximum length :1024
I have a newly installed LMS 4.1 that had the Syslog feature working for a while.
Recently, the Syslog is no longer displaying any records (neither new or old messages).
Below are the steps I have tried to troubleshoot the problem:
- Installed wireshark : Syslog messages are being received by the LMS server on time
- In the Syslog.log file, I can see that all the Syslog messages are being logged properly
- I tried to disable all the "Syslog Message Filters" but nothing changed
In the SyslogCollector.log, I can find the below logs:
NMSROOT is C:/PROGRA~2/CSCOpx
propFileC:/PROGRA~2/CSCOpxMDC omcatwebapps
meWEB-INFclassesC:PROGRA~2CSCOpxMDC omcatwebapps
[Code]....
I get the following error:
SyslogCollector - [Thread: SyslogObjectForwarder] ERROR, 27 Mar 2012 09:02:12,254, Could not send syslogs, removing the subscriber...Connection refused: connect
SyslogCollector - [Thread: SyslogObjectForwarder] ERROR, 27 Mar 2012 09:03:15,223, Could not send syslogs, removing the subscriber...Connection refused: connect
Syslog subscription seems ok but syslog messages are dropped and not forwarded:
I attached SyslogCollector.log, SyslogAnalyzer.log, AnalyzerDebug.log
I have a small problem with a lot of invalid syslog messages in LMS 3.2. Something about 30% of all messages are invalid.
Is there any posibility to get out from which devices those messages are?
Is it a big problem for the application if there are such a lot of invalid messages? I have a lot of devices in my LMS and don't want to get high load because of such unneeded messages.
How do I turn off "logging esm config"? I tried conft no logging esm config and that worked for the moment, but when the switch reboots, or I run reload, it comes back.What does that do anyway? This switch was giving an out of memory error and seemed to be flooded with messages, so I trying to turn logging off/lower the log level.
View 5 Replies View RelatedI've got a ASA5510 with ASA8.3(1), and it's working fine with several group policies, currently handling IPSec and SSL connections. It is authenticating against our AD servers (radius) and I am wondering if it is possible to simply disallow members of a certain OU from connecting. We have a "portal" OU in AD for users who need certain AD functionality, but we wish to disallow them from having VPN access.
View 5 Replies View Related