logging buffered 4096 warnings The above causes router to log all the events with severity level 4 or below in buffer.What about logging console warnings command?will the above command cause router to send log messages with severity level 4( warnings severity level) to console only or will the router send all the log messages with severity level 4 or below to console ?
View 3 RepliesI'm looking to configure a syslog server for all of my cisco device logging. I've had a look at CNA and can't find any options to define a syslog server for my switches.
What's the best way to define a syslog server and the severity of the notifications? Also, i'm looking to clear all previous Syste mmessages fon my devices?
I'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
I recently upgraded a few 2960 switches to 15.0(1)SE, and while they are working fine, I did notice a strange syslog message upon boot-up that wasn't previously there. [code] I did some cursory searching via google but nothing useful presented itself.
View 7 Replies View RelatedI have a pair of 3750E-24PD-S stacked together, it seems after stacked together the stacked switch always flood the console screen with these messages which are not true: [code] Switch-2 is the stack member, Switch-1 is the stack master. The RPS fan failed refers to RPS2300 or the internal power supply of 3750E? Even when I turned on the RPS2300 the stacked switch still display the messages. Also I have two RPS2300 serving stack master and stack member respectively both RPS2300 were switched off why the messages only refer to Switch-2 and not Switch-1? [code]
View 1 Replies View Relatedknow Cisco IOS command, how to show when Catalyst 2960 was shut down (power off)?
View 2 Replies View Relateda number of vlan on trunk is 4096, can I limit this number? I need trunk pass only 10 vlans.
View 1 Replies View RelatedMay I know how to manually set the priority (root ID and bridge ID priority) and for spanning tree? Which one should I use based on the command below? and how does it affect the path cost of it?
set spantree root 1
spanning vlan1 priority 4096
Any switch that supports 4096 multicast groups?I am working on a system that includes over a dozen catalyst 2960 switches. The customer has pointed out the 2960 switch does not satisfy the requirement to support 4096 multicast groups (even though it is more than adequate for the number of active multicast groups). It looks like the 3560 supports more multicast groups than the 2960, but is still far less than the requirement.
View 1 Replies View RelatedIt appears that there are two different types of log information generated by the WLC-5508. The stuff that can be sent directly to syslog seems to be very basic while most of the good log information is sent via snmp trap. Does this setup to log to a SIEM in a manner that gives a good security view into the wireless controller?
View 4 Replies View RelatedI am trying to log every connection (Build, deny, etc).But for some reason I don't see them sh log.
[Code]...
How to set up logging of commands on syslog server ? (cisco nexus 7010)
View 2 Replies View RelatedI found a new bug in cisco IOS 15.1(4)M3 when running EEM script with syslog event detector.If system logging performed using the "logging discriminator" and run concurrently EEM script with syslog event detector, then Cisco router crash and goes to reboot.
Cisco ISR G2 3925E.
I am sending TACACS administration logging to a syslog server. When the messages show up on the syslog server, they are 5 hours ahead of the actual time. Time on the ACS is correct - local logging shows the correct time. Time on the syslog server is correct...all other devices/systems sending syslog messages to it are coming through with the correct time. why the ACS syslog messages would be 5 hours ahead?
View 3 Replies View RelatedWe have a firewall service environment where logging is handled with UDP at the moment. Recently we have noticed that some messages get lost on the way to the server (Since the server doesn't seem to be under huge stress from syslog traffic). We decided to try sending the syslog via TCP. You can imagine my surprise when I enabled the "logging host <interface name> <server ip> tcp/1470" on an ASA Security context and find out that all the connections through that firewall are now being blocked. Granted, I could have checked the command reference for this specific command but I never even thought of the possibility of a logging command being able to stop all traffic on a firewall.
The TCP syslog connection failing was caused by a mismatched TCP port on the server which got corrected quickly. Even though I could now view log messages from the firewall in question in real time, the only message logged was the blocking of new connections with the following syslog message: "%ASA-3-201008: Disallowing new connections."
Here start my questions:
- New connections are supposed to be blocked when the the TCP Syslog server are not reachable. How is it possible that I am seeing the TCP syslog sent to the server and the ASA Security Context is still blocking the traffic?
- I configured the "logging permit-host down" after I found the command and it supposedly should prevent the above problem/situation from happening. Yet after issuing this command on the Security Context in question, connections were still being blocked with the same syslog message. Why is this?
- Eventually I changed the logging back to UDP. This yet again caused no change to the situation. All the customer connections were still being blocked. Why is this?
- After all the above I removed all possible logging configurations from the Security Context. This had absolutely no effect on the situation either.
- As a last measure I changed to the system context of the ASA and totally removed the syslog interface from the Security Context. This also had absolutely no effect on the situation.
At the end I was forced to save the configuration on the ASAs Flash -memory, remove the Security Context, create the SC again, attach the interfaces again and load the configuration from the flash into the Security Context. This in the end corrected the problem. Seems to me this is some sort of bug since the syslog server was receiving the syslog messages from the SC but the ASA was still blocking all new connections. Even the command "logging permit-host down" command didn't wor or changing back to UDP.
It seems the Security Context in question just simply got stuck and continued blocking all connections even though in the end it didn't have ANY logging configurations on. Seems to me that this is quite a risky configuration if you are possibly facing cutting all traffic for hundreds of customers when the syslog connection is lost or the above situation happens and isn't corrected by any of the above measures we took (like the command "logging permit-host down" which is supposed to avoid this situation altogether).
I received a syslog message on my cisco 3845 router, what is that message mean. 11 13:36:06.265 UTC: ASSERTION FAILED: file "../les/if_ng_dslsar_tx.c", line 385
View 2 Replies View RelatedWe have 2 Cat 6509 connected to 1 Gbps Ethernet WAN Link. On each 6509 we use 2 Gbps IPSec SPA Encryption cards for Encryption. The encrypted traffic goes to a GRE Tunnel. This morning I found some error messages in syslog.
%CONST_DIAG-SP-3-HM_TEST_FAIL: Module 1 TestIPSecEncrypDecrypPkt consecutive failure count:2
There were also several short tunnel downs/ups. I wonder if there is a bug in the new IOS image 12.2(33)SXI2a. We upgraded to this image last weekend.
I want to use an EEM applet on a Cisco IOS 2431 voice gateway running 15.1(2)T to take action upon expiration of a SIP registration (with its sip registrar). I thought that it might be possible to use existing error messages generated by the ios sip application to trigger an EEM applet.Is there a reference that lists all SYSLOG messages that SIP can generates, and their error levels? Can you show me how to turn on syslog messages, so that I can cause a SIP registration expiration on my GW and then see what SYSLOG messages are produced?
I think I understand how to write an applet and its event trigger from a SYSLOG message pattern, but I am having trouble seeing any SIP error messages at all, except if I turn on Debug, which usually produces way too many messages and may impact performance.
I keep getting an error message, i've tried several things to resolve it but still no success.This is the exact error message:
regular translation creation failed for protocol 41 src Customer: dst outside:
It is a Customer requirement to send 802.11 client association/disassociation logs to the Syslog server in a Unified Wireless system. (AIR-CT5508 + LAP1142) [code] Unfortunately I didn't find such logs even in Msg Log with the severity level set to debugging.I was able to do client assoc/disassoc logging with SNMP trap + trap receiver software, BUT is there any way to do this with Syslog?
View 1 Replies View RelatedNow I'm trying to write software that get information from Syslog message, but I'm facing with the problem about getting statistic of client de-authenticated in a WLC (Software Version: 7.0.98.0), because I cannot find any log about this information on WLC except only this SNMP trap:
Tue Aug 23 09:52:28 2011Client Deauthenticated: MACAddress:00:xx:77:2c:06:db Base Radio MAC:00:xx:5d:0c:fc:30 Slot: 0 User Name: unknown Ip Address: 10.2xx.47.15 Reason:Unspecified ReasonCode: 1
So, is there any way that I can configure WLC to convert this SNMP trap to send to Syslog server as a normal Syslog message?
I'm fine tuning some of our ASA logging config, and am having an issue with one particular syslog ID.The message is: syslog 106100: default-level informational (enabled)and the log settings are:
Syslog logging: enabled
Facility: 20
Timestamp logging: enabled
Standby logging: disabled
Debug-trace logging: disabled
[code]....
This ACE log entry is generated by explicit deny any any statements at the end of all the ACLs, e.g.access-list inside_access_in extended deny ip any any log interval 600 Based on the config, I would expect to see this being logged to the syslog server, but not to the local buffer, but am still seeing them locally in the buffer:
Feb 22 2012 10:58:20: %ASA-4-106100: access-list inside_access_in denied udp INSIDE/HOSTABC(52629) -> OUTSIDE/HOSTXXX(162) hit-cnt 5 300-second interval [0x3baecf1e, 0x0]
It also still shows these as level "warning", %ASA-4-106100, instead of the default %ASA-6-106100 I've tried removing and re-applying the config at different levels but it still reports in the buffer log as level "warning", %ASA-4-106100 This also doesnt affect every 106100 log that is generated. Most messages are generated at the correct level 6 severity but some seem to randomly log at level 4. There doesn't seem to be any pattern to this. The same access-list line can produce severity level 4 and 6 106100 messages.
Receiving the following syslog message from a 4402 WLC:
%CAPWAP-3-AP_DB_ALLOC: capwap_ac_db.c:145
Unable to allot AP entry in database. We receive this message about once a minute on average. I can't find any documentation saying what it is. It looks like a database error, which makes think it might be a memory issue or an issue with having too many AP's on the WLC. However, that controller has less than 30 AP's on it.
For some reason I am unable to retain the system message logging and config archive references after a reboot of the router. I need to be able track config changes and retain the ability for the customer to recover the original config should they destroy the config through any misguided fiddling on their part. There is no remote management and these router need to be recoverable. I know this used to configured by default on earlier routers as I've checked on teh ones we have, but checking through the configuration has not worked and i have everything configured the same but system messages are still lost on reboot. Im using Cisco 3845 running IPbase 12.4(3) and the config i have is shown below.
Logging buffered 4096 debugging
no logging console
!
!
Archive
Log config
Logging enable
Logging size 100
Notify syslog
Hidekeys
Path flash:archive-config
!
Logging history size 200
Logging facility local6
Unable to see the logging message on the user context on ACE,but able to view the logging on the Admin Context.
Admin# sh logging
Message logging: none
Buffered logging: enabled (level - debugging) maximum size 1048576
Buffer info: current size - 1048576 global pool - 1048576 used pool - 1048576
min - 0 max - 1048576
cur ptr = 916918 wrapped - yes
[code]....
For WLC 5508 software version 7.0.235.0, which command is needed to get the WLC send syslog messages everytime a wireless client associate and desassociate?
View 2 Replies View RelatedI'm running a home network with 3 computers via a linksys router attached to a westell modem. Is there a local network messaging system I can use to pop a message on a screen to one of the other computers? Can I use DOS?
View 1 Replies View RelatedAfter setting thru set time command, error message is display on server 'synthetic time issued'.
View 2 Replies View Relatedhow do i broadcast a message on my network using command prompt?
View 2 Replies View Relatednet send command not working. Even after starting messenger. Error : The Message Alias could not be found on the network
View 3 Replies View RelatedIs there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.
View 2 Replies View RelatedI am looking for a way to see packets that are matched on certain ACLs in a CoPP policy map. I have read that it is not a good thing to add the log keyword at the end of an ACL when using that ACL for CoPP. I initially tried to use a logging policy map but the 6500 12.2sx doesn't support this.
how I can see source/destination IP for a certain class in a CoPP policy map?
I am looking for soem best-practice and useful logging commands on 6500 and 3750 platforms. Some of them I have listed below. Is there any important ones I am missing Also, I need to know what kind of recommended logging level is for buffer and what is loggign level for syslog server?
View 1 Replies View Related