It is a Customer requirement to send 802.11 client association/disassociation logs to the Syslog server in a Unified Wireless system. (AIR-CT5508 + LAP1142) [code] Unfortunately I didn't find such logs even in Msg Log with the severity level set to debugging.I was able to do client assoc/disassoc logging with SNMP trap + trap receiver software, BUT is there any way to do this with Syslog?
View 1 Replies
Recently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies View RelatedI'm trying to do some basic troubleshooting on our WiSMS. Some clients on a working network are unable to connect in the afternoons, debugging the client on the wism shows this message:
*apfMsConnTask_2: Dec 05 14:23:44.018: Association request from the P2P Client Process P2P Ie and Upadte CB
It keeps repeating with the Task_X changing.What does that mean?We have two controllers in our 6500's running this software ver. 7.3.101.0
I have been noticing in my trap logs that there are an excessive amount of Client Association/Authentication Failures. I cannot figure out why. I have a Cisco 5508 WLC with 81 AP's (1131ag, 1142abgn, 1262N) models. The wireless devices are on a Windows Domain and use 802.1x EAP authentication, authenticating the user and computer info with a RADIUS Server. I look at the logs and all it can tell me is Reason:Unspecified ReasonCode:1. I read that the Reason Code is due to "Client associated but no longer authorized" but to be honest I am not sure what that means.
View 9 Replies View RelatedNow I'm trying to write software that get information from Syslog message, but I'm facing with the problem about getting statistic of client de-authenticated in a WLC (Software Version: 7.0.98.0), because I cannot find any log about this information on WLC except only this SNMP trap:
Tue Aug 23 09:52:28 2011Client Deauthenticated: MACAddress:00:xx:77:2c:06:db Base Radio MAC:00:xx:5d:0c:fc:30 Slot: 0 User Name: unknown Ip Address: 10.2xx.47.15 Reason:Unspecified ReasonCode: 1
So, is there any way that I can configure WLC to convert this SNMP trap to send to Syslog server as a normal Syslog message?
I'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan controller 5500 controller with AP (aironet 3500). I want to detect for rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to detect this behavior.
Authorize AP's against AAA function to make sure that all the AP's registering to your WLC are authorized AP's of the network.By enabling this feature, only those AP's whose mac-addresses are present in the authorization list, will be able to register to the WLC. url...
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it. url...the forum I have seen other talks about the same issue and saying that if I have any APs in "Rogue Detection" mode sitting on the trunk port on the switch then only, this AP will detect the Rogue on Wired.
I am running WLC 5508 and WCS version 7.0.98. We are noticing with some of our handheld devices that have Sychip Wireless cards that they constantly have issues communicating. The error I see on the WCS side is shown below:
Client '00:0b:6c:2f:d0:32 (0.0.0.0)' failed to associate with interface '802.11b/g' of AP 'HO-BRSales'. The reason code is '0(null)'.
I received a syslog message on my cisco 3845 router, what is that message mean. 11 13:36:06.265 UTC: ASSERTION FAILED: file "../les/if_ng_dslsar_tx.c", line 385
View 2 Replies View RelatedWe have 2 Cat 6509 connected to 1 Gbps Ethernet WAN Link. On each 6509 we use 2 Gbps IPSec SPA Encryption cards for Encryption. The encrypted traffic goes to a GRE Tunnel. This morning I found some error messages in syslog.
%CONST_DIAG-SP-3-HM_TEST_FAIL: Module 1 TestIPSecEncrypDecrypPkt consecutive failure count:2
There were also several short tunnel downs/ups. I wonder if there is a bug in the new IOS image 12.2(33)SXI2a. We upgraded to this image last weekend.
I want to use an EEM applet on a Cisco IOS 2431 voice gateway running 15.1(2)T to take action upon expiration of a SIP registration (with its sip registrar). I thought that it might be possible to use existing error messages generated by the ios sip application to trigger an EEM applet.Is there a reference that lists all SYSLOG messages that SIP can generates, and their error levels? Can you show me how to turn on syslog messages, so that I can cause a SIP registration expiration on my GW and then see what SYSLOG messages are produced?
I think I understand how to write an applet and its event trigger from a SYSLOG message pattern, but I am having trouble seeing any SIP error messages at all, except if I turn on Debug, which usually produces way too many messages and may impact performance.
I keep getting an error message, i've tried several things to resolve it but still no success.This is the exact error message:
regular translation creation failed for protocol 41 src Customer: dst outside:
I would like to send my ASA 5500 logs to more than one syslog server - is this possible? I can't seem to find it in the documentation.
View 3 Replies View RelatedWe use multiple ASA 5500/5580 cluster systems running 8.3 software versions.Actually we send all our FW syslog data to a SIEM appliance in a DMZ on a remote firewall (non-asa). Recently we suffered a strange incident while implementing a new SIEM collection station now situated in a dmz that is located on one of the ASA contexts. We redirected the syslog streams to the new client for one of the contexts on the ASA cluster that holds the new SIEM agent DMZ..since we did this and redirected the syslog we see double traffic and spoofing errors on that context
a/ the ASA keeps sending out the syslog traffic to the OLD SIEM agent server ip (there is however no trace of its ip in the config)
b/ the traffic leaving the interconnection interface towards the OLD SIEM agent gets a SPOOFING error on the traffic
c/ strangely the data gets also correctly forwarded to the new SIEM collection stations.
We started out with redirecting traffic on only one of the 5 contexts to the new environment and kept logging the others to the old system.I finally got out of the issue by reconfiguring al the other contexts to forward their syslog towards the same new server , since that moment we no longer have the double logging and spoofing error , all syslog traffic goes correctly to the new SIEM agent. It looked like some remenants of the old syslog config remainded on the asa event after deleting and introducing a new config line (we used the asdm to execute the action) as said either it kept the old config or it looked in the other context and "decided" to keep sending to the old server also mentioned in that syslog can find the behaviour in any buglists either way.
I'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan controller 5500 controller with AP (aironet 3500). I want to detect for rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to detect this behavior. I'm doing this step.
Authorize AP's against AAA function to make sure that all the AP's registering to your WLC are authorized AP's of the network.By enabling this feature, only those AP's whose mac-addresses are present in the authorization list, will be able to register to the URL
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it.URL
NOTE: from the forum I have seen other talks about the same issue and saying that if I have any APs in "Rogue Detection" mode sitting on the trunk port on the switch then only, this AP will detect the Rogue on Wired
I don't think i completely understand this statement, by sitting does it mean that it is passively sniffing coming in/out on trunk link?
Considering the above steps are accurate, after this will i be able to see rogue detection behavior in syslogs? What exactly would be the messages that would produce this behavior.
I'm fine tuning some of our ASA logging config, and am having an issue with one particular syslog ID.The message is: syslog 106100: default-level informational (enabled)and the log settings are:
Syslog logging: enabled
Facility: 20
Timestamp logging: enabled
Standby logging: disabled
Debug-trace logging: disabled
[code]....
This ACE log entry is generated by explicit deny any any statements at the end of all the ACLs, e.g.access-list inside_access_in extended deny ip any any log interval 600 Based on the config, I would expect to see this being logged to the syslog server, but not to the local buffer, but am still seeing them locally in the buffer:
Feb 22 2012 10:58:20: %ASA-4-106100: access-list inside_access_in denied udp INSIDE/HOSTABC(52629) -> OUTSIDE/HOSTXXX(162) hit-cnt 5 300-second interval [0x3baecf1e, 0x0]
It also still shows these as level "warning", %ASA-4-106100, instead of the default %ASA-6-106100 I've tried removing and re-applying the config at different levels but it still reports in the buffer log as level "warning", %ASA-4-106100 This also doesnt affect every 106100 log that is generated. Most messages are generated at the correct level 6 severity but some seem to randomly log at level 4. There doesn't seem to be any pattern to this. The same access-list line can produce severity level 4 and 6 106100 messages.
Receiving the following syslog message from a 4402 WLC:
%CAPWAP-3-AP_DB_ALLOC: capwap_ac_db.c:145
Unable to allot AP entry in database. We receive this message about once a minute on average. I can't find any documentation saying what it is. It looks like a database error, which makes think it might be a memory issue or an issue with having too many AP's on the WLC. However, that controller has less than 30 AP's on it.
logging buffered 4096 warnings The above causes router to log all the events with severity level 4 or below in buffer.What about logging console warnings command?will the above command cause router to send log messages with severity level 4( warnings severity level) to console only or will the router send all the log messages with severity level 4 or below to console ?
View 3 Replies View RelatedI recently upgraded a few 2960 switches to 15.0(1)SE, and while they are working fine, I did notice a strange syslog message upon boot-up that wasn't previously there. [code] I did some cursory searching via google but nothing useful presented itself.
View 7 Replies View RelatedI have a pair of 3750E-24PD-S stacked together, it seems after stacked together the stacked switch always flood the console screen with these messages which are not true: [code] Switch-2 is the stack member, Switch-1 is the stack master. The RPS fan failed refers to RPS2300 or the internal power supply of 3750E? Even when I turned on the RPS2300 the stacked switch still display the messages. Also I have two RPS2300 serving stack master and stack member respectively both RPS2300 were switched off why the messages only refer to Switch-2 and not Switch-1? [code]
View 1 Replies View RelatedThe Release Notes for 7.0.116.0 of WLC 5500 has a table which title is "Client Type", and it shows wireless adapters. My question is,
what kind of customer means? Wireless clients or clients for an specific application? If it was the first option, does it mean tha just this adapters could connect to my wireless network?
I have cisco 5550 Firewall, one messages appear in syslog server from Firewall, (warning) i want to stop this message from appearing syslog traps.
View 2 Replies View RelatedThe message ID I can use to filter VPN clients connecting and disconnecting from the Firewall?
View 1 Replies View RelatedI have been trying to conect a Cisco VPN client through an ASA and it makes the connection but doesn't allow any traffic through. The ASA does have a site to site VPN attached to the outside interface.I suppose the first question is it possible to allow VPN client to connect through an ASA 5500 from the inside network when there are Site to Site VPN's already attached to the outside interfaces?If possible then what have I missed. I have tried adding NAT exempt for the traffic between the internal networks and "an IPSEC pass thru Inspect Map".
View 4 Replies View Relatedtying to connect CSM client to CSM server (ver 4.0) and getting attached error message. The server is running, no errors reported while installation, all services are up and fine. I tried to install client locally on the server and connect it that way with no luck. CSM server runs on Win 2008, firewall disabled.
View 0 Replies View RelatedHaving an issue with my WLC 5500 and client connectivity. This just started today. Clients will connect for a short period of time and then drop off. WLC appears fine with the exception of a bunch of trap errors. I've rebooted the WLC but this did not clear the issue.
View 3 Replies View Relatedi am trying to configure static ip on remote client user side , i am using the following doc as an example but i am not getting the ip which i am mentiong in the user .[url]...
View 10 Replies View RelatedUsing AnyConnect Secure Mobility Client, logging into ASA5540. After I put my credentials in, I get the banner message (from group policies). After I accept that, I get another pop message stating:It looks like a pre-set message. Where can I disable and/or edit this message?
View 4 Replies View RelatedAdd the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies View RelatedHad some problems with the association of the MSE with the WCS.Licenses already loaded context aware and WCS-PLUSThe two machines are within the same network segment WCS (10.16.0.28) and MSE (10.16.0.89), including IP connectivity exists and which tests ping.When I do a / etc / init.d / mse status throws me the following error:
root@xxxxx# /etc/init.d/msed statusSTATUS:MSE Platform is up, getting the statusUnable to get MSE status. Error: (400)Bad RequestRetrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status.
[code]......
I have Dell Inspiron 15 3520 laptop bought in December 2012 with Windows 8 Pro. It was working fine until two days ago. I am unable to obtain DHCP lease either through wireless or wired network. After troubleshooting, I found DHCP service is not running and try to restart but of no avail.I ran sfc /scannow and the results are OK.
View 2 Replies View RelatedHas used the "Planned AP association" feature in WCS 7 planning mode? I haven't been able to find any documentation on it, but I was hoping that it allowed you to map your planning AP's and locations to freshly deployed AP's and place them on the floorplan when doing a synchronize, but I can't get it to complete successfully.
View 3 Replies View RelatedI just upgraded a 1812w from 15.1 to 15.2 and did NOT change any configs/passwords or anything else.
My WiFi Clients are not able to associate any more. Failure is:
Sep 20 13:59:19.384: %DOT11-7-AUTH_FAILED: Station 0001.0203.0405 Authentication failed
I can't find either a WLAN-configuration guide for 15.2.
relevant config:
dot11 ssid wlan2
vlan 2
max-associations 16
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 0 password2(code)
-WLC 2504
-AP1602
-SW 7.4.100.0
We have 22 x AP1602.5 of them show up in the WLC with Controller Association Latency of around 1 minute and 10 seconds.The other 17 all have latency around 10 seconds.
1. What are possibile causes for high value of association latency?
2. Could high-value association latency be an indication of badly working wifi for data traffic?
